hursst Posted January 23, 2021 Share Posted January 23, 2021 Hello, I saved a Stromburg Model WW from the junkyard recycle pile (see photo). I can clearly see "Stromburg WW" and the Bendix logo near all the patent numbers, but I can't fine the specific part number that will tell me what it fits. I did some preliminary research, and I think there may have been a tag attached (it is missing) with it, but I see no other numbers on the carb. Does anyone know what car(s) this fits and/or can someone tell me where the part number may be, if there is one? Thanks! -Chris Link to comment Share on other sites More sharing options...
carbking Posted January 24, 2021 Share Posted January 24, 2021 From my website thecarburetorshop.com: Jon Stromberg The following applies to Stromberg-USA carburetors, and does not apply to Stromberg carburetors produced elsewhere: Stromberg began stamping a ‘code’ number on virtually all O.E. (original equipment) carburetors beginning in 1935 up through the end of production in 1974. Most of the carburetors produced in the late 1930’s were stamped on the throttle body. Others were stamped on the airhorn. After 1940 this trend was reversed, and most carburetors were stamped on the top surface of the airhorn along one of the edges. Replacement carburetors produced during this period were generally identified by tag only (although a few replacements were stamped). The stamped ‘code’ is in the format ‘ccc-nnne’ where ccc is a one, two, or three digit code representing the company for which the carburetor was produced (ie 2=Ford, 4=Chrysler, 7=Buick, etc.); nnn is a one, two, or three digit number representing the next sequential number of carburetor sold to the company in ‘ccc’; and e is a letter (if present) representing the engineering change status of the carburetor. An example would be 7-69A which is decoded as 7 (Buick); 69 (the sixty-ninth type of carburetor sold to Buick – this one fits a 40 series in 1949); and ‘A’ meaning one engineering change to the original specifications. A second change would be 7-69B. Stromberg used both rectangular (held in place by a screw) and round (riveted in place) tags during this period, on those units which were tagged. Stromberg carburetors produced prior to 1935 can easily be identified as to type, as it is cast onto the carburetor; however complete identification is impossible unless one has prior knowledge of the carburetor being identified; and can be quite difficult and time consuming for even someone with the original prints. Link to comment Share on other sites More sharing options...
hursst Posted January 24, 2021 Author Share Posted January 24, 2021 I greatly appreciate the response, but this is not helpful. I need to find out where the code number may be on the carb, other than the "WW." If it may have been just a tag that was affixed to the carb, then it is missing from it, so I won't be able to tell, unless someone else can identify the specific model of the carb. Thanks. Link to comment Share on other sites More sharing options...
carbking Posted January 24, 2021 Share Posted January 24, 2021 From above: "After 1940 this trend was reversed, and most carburetors were stamped on the top surface of the airhorn along one of the edges. " Jon Link to comment Share on other sites More sharing options...
hursst Posted January 24, 2021 Author Share Posted January 24, 2021 Thanks again, yes I read this, but again, this is too vague. Specifically where on the airhorn? I see no numbers anywhere on mine, but I could be overlooking it, or there may be no number at all, which is most likely the case. If I know exactly where to look, I can confirm whether or not have have a number on mine or not. I do appreciate the effort to assist. Link to comment Share on other sites More sharing options...
roysboystoys Posted January 24, 2021 Share Posted January 24, 2021 2 hours ago, hursst said: Thanks again, yes I read this, but again, this is too vague. Specifically where on the airhorn? I see no numbers anywhere on mine, but I could be overlooking it, or there may be no number at all, which is most likely the case. If I know exactly where to look, I can confirm whether or not have have a number on mine or not. I do appreciate the effort to assist. It varies with production years. Some are on top of the float bowl , hard to miss. Some are on the edge of the air horn cover , usually passenger side. If the area is clean you will find it , unless it's the one made on Monday after a holiday and it was not stamped. Link to comment Share on other sites More sharing options...
hursst Posted January 24, 2021 Author Share Posted January 24, 2021 (edited) Carb and Roy, thank you very much for your posts. The "top of the float bowl" was the tip I needed. Had to use a magnifying glass, but was able to find it with a little more effort; numbers are there. It is a 3-164. There is one on ebay that says it is for a 1958 Dodge truck. Another ad says 1956-1959 Dodge Coronet D66, 67, 70, 71, 72 LD2 1956-1959 Dodge D-63-1 Red Ram 1956-1959 Dodge D-62-2-3 Super Red Ram Would anyone know if there are other applications? Thanks again! Edited January 24, 2021 by hursst (see edit history) Link to comment Share on other sites More sharing options...
pkhammer Posted January 24, 2021 Share Posted January 24, 2021 Dodge 8 cyl 1956 - 59 D-63-1 RED RAM, D-63-2-3 SUPER RED RAM, D-66, D-67-1, D-70, D-71, D-72, LD2-L CORONET 3-135, A, B, 3-136, A, B, 3-137, A, B, 3-138, A, B, C, D, 3-139, A, B, C, D, 3-140, A, B, C, D, 3-149, A, B, 3-150, A, B, C, 3-163, 3-164, 3- 181, 3-182, 3-183, A, B Link to comment Share on other sites More sharing options...
hursst Posted January 24, 2021 Author Share Posted January 24, 2021 pkhammer, thanks for the info, but not sure how to read this. It shows a large amount of other carb numbers besides just 3-164. Does 3-164 have a specific application, or will 3-164 and all the other model numbers listed fit all the 1956-59 applications listed? Not sure if you know either, you may just be passing on what you have. -Chris Link to comment Share on other sites More sharing options...
carbking Posted January 24, 2021 Share Posted January 24, 2021 Ebay isn't always correct. https://www.thecarburetorshop.com/Kdodge.htm Jon Link to comment Share on other sites More sharing options...
hursst Posted January 24, 2021 Author Share Posted January 24, 2021 Jon, Fantastic! That answers all the questions, 1958 325 LD2-L and Coronet. Greatly appreciate all the help, hope I can return the favor with other folks' questions in the future. I also know where to go when I need carburetor rebuilds now, too. Chris Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now