jdshott Posted April 7, 2019 Share Posted April 7, 2019 Vintiage Pontiac Flathead Owners: In another thread Paul asked if I had a 1937 Pontiac timing hole cover and, if so, could I share pictures. I think that I have a two part answer: (1) Yes, I have a timing hole cover and (2) No, it is not from a 1937. Here is a picture of the metal timing hole cover that I have: It measures 1 9/16" in length and 1 5/16" in width (approximately). I have also included a side and oblique view to show a bit more detail. Finally, I have included the drawing of the clutch housing from my collection of multi-year Pontiac Master Parts books. The drawing for the 1937-38 clutch housing does not show the actual timing hole cover (part group 0.714), but it does show that all 1926-1936 Pontiac engines used part number 487833. It then lists 1938-1939 as part number 501383. The 1939 clutch housing drawing shows a rubber timing hole cover ... so the 1938 (and, I suspect, the 1937) used the rubber timing hole cover. Finally, the drawing for the 1041-1942 clutch housing shows the metal timing hole cover that I appear to incorrectly have on my 1937 6-cylinder engine. I don't know how far beyond 1942 they used the same metal timing hole cover. If anyone has more details, I'm sure we'd appreciate learning something further. Thanks, John Link to comment Share on other sites More sharing options...
kookie1 Posted April 7, 2019 Share Posted April 7, 2019 Nice sleuth work on the rubber timing hole cover John. I've looked into it in the past and found that Steele Rubber doesn't make a reproduction of the rubber cover. I was figuring they for sure would have one on their rubber item list since that's their specialty but I guess not. I also looked into California Pontiac Restoration and Kanter Auto Parts out east but they don't have it either. I was hoping someone made a reproduction of it but I guess I'll still be looking. I imagine few timing hole covers survived due to years of under the hood heat that dries out the rubber and makes it stiff and brittle. Which is probably why they simply shrink a bit and fall out of the hole over time. I'll keep looking though anyway. Thanks for the research. Maybe someone will chime in with more insight!! Paul Link to comment Share on other sites More sharing options...
john hess Posted April 15, 2019 Share Posted April 15, 2019 My 53 l8 4 door has the metal hole cover just like your pictures.... John Link to comment Share on other sites More sharing options...
jdshott Posted April 16, 2019 Author Share Posted April 16, 2019 John: Thanks for that input. At this point, my working theory is that Pontiac 6 and 8 used the metal timing hole cover starting in ‘41 through the end of the flathead era. I also thing that the ‘37-‘39 used the rubber cover, with 1940 being unknown. Of course, I may be wrong and hope that anyone who knows differently will enlighten me. Thanks again, John, for your response. John Link to comment Share on other sites More sharing options...
PETEPONTIAC-1 Posted April 16, 2019 Share Posted April 16, 2019 here are pictures of my timing hole cover off my 38 Pontiac ,, PP Link to comment Share on other sites More sharing options...
PETEPONTIAC-1 Posted April 16, 2019 Share Posted April 16, 2019 more pic's Link to comment Share on other sites More sharing options...
kookie1 Posted April 17, 2019 Share Posted April 17, 2019 Thanks for the pix, PP. You've shown us these before in a previous post but this time with measurements. That definitely helps! I'm wondering if the strap across the front, which I assume is to pull it out of the timing hole, is made of the same foam rubber or is it made of something else? It's hard to tell from the pix. I'm also wondering if one could fabricate a copy with a 3D printer using a denser plastic that can be printed, which requires some serious heating of the plastic to liquefy it, and end up with a hole cover that can handle the under-the-hood heat buildup? Guess I'd have to know more about 3D printers and certain plastic's properties. Anyway, just a thought. I'm amazed your timing hole cover looks that good with almost no deterioration after all these years. Paul Link to comment Share on other sites More sharing options...
PETEPONTIAC-1 Posted April 17, 2019 Share Posted April 17, 2019 Well if you find someone with a 3 D printer maybe we can have some made !!! PP Link to comment Share on other sites More sharing options...
jdshott Posted April 18, 2019 Author Share Posted April 18, 2019 PP and Paul: Thanks for those nice photos and discussion. When I have a chance, I’m going to talk to some folks that know a lot about 3D printing. I’m not sure they will do something like this for me. However, if I am not mistaken, the process is roughly: 1. Use a 3D printer to print a model in just about any material. 2. Send the model to someone like Steele Rubber. They make a mold from the original model and then use that to make parts out of their standard rubber material. I don’t know what they charge for setup … and what the resulting per part would cost, but it seems as if it is worth exploring … Thanks again for those photos. John Link to comment Share on other sites More sharing options...
SixPack77 Posted August 21, 2019 Share Posted August 21, 2019 I am trying to find the timing hole or pointer on my 1952 Pontiac Chieftain 268.2 cu in straight eight. Could anyone tell me the approximate location? Thanks! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now