Kean Thompson

Thanks Mike.

WANTED. Hi there, does anyone have a radiator and surround for a 745 Packard? Also need side mount brackets that bolt to the chassis. Both of these are unique to a 745 If anyone has a 745 rolling chassis or 745 parts car or project 745, I'd be interested. speedster1930@hotmail.com

WANTED - Myself and two friends have Mitchell Model S, 6 cylinder and Model T, 4 cylinder cars. These are rare in Australia (and obviously rare anywhere it seems). We are seeking parts - almost anything would be useful. What have you - we can use motor parts, transmission, radiator - just about anything. All information in confidence. speedster1930@hotmail.com

WANTED - Myself and two friends have Mitchell Model S, 6 cylinder and Model T, 4 cylinder cars. These are rare in Australia (and obviously rare anywhere it seems). We are seeking parts - almost anything would be useful. What have you - we can use motor parts, transmission, radiator - just about anything. All information in confidence. speedster1930@hotmail.com

I got this steering wheel years ago with some Packard parts. There were also some Cord parts but someone went to a lot of trouble to package this up. Does anyone know what it is from? speedster1930@hotmail.com

Are 1929 La Salle wire wheel caps the same - that is Buffalo #5?

Good thinking. Thanks.

Does anyone have access to large shipping crates in the PA or close by area? Need a couple approximately 45 X 45 X 45 and a couple 45 X 45 X 90. speedster1930@hotmail.com

Can some suggest who might move a Packard motor and transmission, still mounted in a cut-off chassis frame. It need to go from Montana to Long Beach. I have tried U-ship - no replies. Photo for reference. This is urgent. speedster1930@hotmail.com

http://www.ebay.com.au/itm/292406732621?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649

I have a set of these rather nice wheels. Diameter at front = 24" Hub Diameter = 8 1/4" Rear Brake Drum Diameter = 13" Hub bolts = 3" between and 6 1/4" across the centre If anyone knows what rims are required to attach to these, please let me know so I can 'begin the hunt'

Still needed. What have you got?

WANTED. I need a 1931 Packard 840 engine - complete or just major parts. speedster1930@hotmail.com

WANTED. I need a 1931 Packard 840 engine - complete or just major parts. speedster1930@hotmail.com

Mike, Do you still have these?

A direct e-mail sent minutes have you made the listing.

PM sent.

Private message sent.

I am confident there's a radiator out there. Please check your spares. I would even buy a job lot of parts or a project car 1929-1931. What have you? HELP!!! Parts can be collected your location. I ship with USA to OZ out of West Coast or East Coast.

In addition to the radiators, I also need (1) LHS front fender for an 840 Packard.

G'day Ben, The 645 radiator is a couple of inches taller and, therefore, the hood. Since I need one of each, I wasn't going into that and complicating things. I am delighted to get your reply - the first. Now I just need one offering me a radiator. I have several Std 8 radiators and cores but hold out hope that there is one out there. I also need a 745 and that's going to be harder than the 645. I do have tonnes of spares and could swap or pay good $. Thanks again Ben.

I need a radiator for 1929 Su 8 Packard. Can anyone help?

Don't seem to have had a reply to my PM. Could I ask that you let me know when and where you advertise the Manual? Thanks.

Hi, Just sent you a Private Message. speedster1930@hotmail.com

I will add some measurements tomorrow.