Riviera63

You are welcome. They aren't that bad. Just take getting used to. Once you get the hang of it, it is a piece of cake. These are the Cadillac of wheel covers compared to the cheap flimsy crap on other makes and models. Just the weight of them is impressive. Bill

I am sure others have their methods. This is mine. Attached are pictures of my weapon of choice. I first put a piece of cardboard underneath the tire. As gungeey pointed out they can fly off and hit the cement floor. They are heavy too, which makes a sudden grab more difficult if they come off. Slow and easy is the trick. The wheel covers can be easily damaged if you pry too hard or use something with sharp edges, such as a tire iron. I wrap the end of my pry tool with duct tape to keep this from happening. I also insert a 3" X 3" piece of 1/4" thick paneling between the rubber head of the tool and the tire. You do exert a lot of pressure and this keeps the rubber head from sinking into the tire making it harder to pry. As gungeey said go around around a little at a time. You can tell when it starts to come loose. Once you get it free in one spot, removal is pretty easy. Once you do it a few times you will get the hang of it. When you put them back on use the heel of your hand. They will seat just fine. Again once you do it a few times you will get the hang of getting them on. Do not pound them back on, even with a rubber mallet. They can be damaged. Hope this helps. Bill

Sold

UPDATED I have purchased two 1963 Rivieras and an assortment of miscellaneous parts. I will list some things here but, if there is something specific you are looking for PM me and I will see if I have what you are looking for. Thanks. 1.) 10 very nice right hand thread lug nuts 3.) Parking brake adjustment bracket and parking brake spring pin 4.) 2-1963 & 1964(?) standard interior rear quarter panel stainless trim pieces, enough for one side, can be used on either side 11.) Passenger side console plastic kick panel plate-I have 2 54.) 1965 console shifter bezel and shifter guide 57.) 1965 Front upper bumper brackets with attaching hardware 59.) 1965 lower front bumper support bar 68.) Console heater/AC air spring hose clamps 89.) Suction Throttle Valve bracket with attaching hardware 95.) 1965 front bumper filler panel/lower tie panel 105.) Blower motor-AC car-tested working 112.) 1965 Headlight Switch 118.) Driver's door long stainless beltline trim molding 119.) Upper cowl panel 122.) AC receiver/dehydrator brackets, clamps and attaching hardware 128.) Passenger side lower dash pad 130.) 4 access panel attaching clips-2 needed per panel 134.) Blower motor to firewall ground wire 136.) 1963 dash pad defroster grill with attaching hardware-I have 2 138.) 1965 speedometer cable with housing and connectors 141.) Master cylinder with screw on cap 144.) Air distribution duct that connects to evaporator 146.) 1965 Brake booster 148.) Throttle operating lever with throttle return spring 151.) Passenger's side rear quarter window stainless beltline trim molding 152.) SOLD-Driver's side rear quarter window stainless beltline molding 155.) Passenger's door long stainless beltline trim molding 156.) Heater box with gasket 157.) SOLD-Miscellaneous 1965 horn and steering wheel components 160.) Inner fender door hinge cover filler panels-for car without electric windows 161.) Power Steering gear box 167.) 1963 left side dash access panel-have 2 168.) 1963-1965 rear seat below speaker filler panel-for back seat without a center armrest 171.) 1963-1965 middle lower rear seat filler panel 172.) Pair very nice 1963-1965 upper back seat side filler panels 173.) Rear quarter window leading edge weatherstrip stainless trim molding-have 2-will fit either side 174.) 1963-1965 deluxe interior door armrest pads-have 2-will fit either side 177.) Passenger side front console kick panel extension-have 2 178.) Horn bracket with attaching hardware-for horn(s) behind grill 179.) SOLD-Pair console rear heat vents 180.) Passenger deluxe interior armrest power window switch bezel 181.) SOLD-Driver deluxe interior armrest bezel with power windows and power seat 182.) Steering column ribbed aluminum trim for non-tilt wheel 183.) 1963 fuse box bracket 186.) Steering column support brackets 188.) 1965 trunk wiring harness 193.) 1963-1964 radio knobs 194.) 1963-1964 headlight switch knob, stem and bezels-have 2 sets 195.) SOLD-Two tone red steering wheel 198.) Passenger vent window beltline stainless trim molding-have 2 199.) Driver vent window beltline stainless trim molding-have 2 200.) Rear quarter stainless trim molding-will fit either side-have 2 201.) 1963-1964 Vacuum trunk release controller, actuator and mounting bracket-tested-working 202.) 1963-1964 Vacuum trunk release actuator-tested-working 203.) 1963-1965 4-way power seat-under seat wire harness-deluxe interior 204.) SOLD-4-way power seat motor-commutator bars cleaned and sanded smooth-shaft relubed-tested-runs smoothly both directions 205.) 4-way power seat transmission-completely cleaned, degreased and relubed 206.) Standard interior door armrest pads 207.) Power window wiring harness-passenger door-deluxe interior (work for standard interior?) 209.) 1963 Glovebox door script 210.) SOLD-Turn signal and high beam lenses and assembly-1 left 211.) 1965 lighter element and knob 212.) 1963 heater/AC switch dash cover plate 213.) 1963 glovebox light and lens 215.) Complete set dash cluster light sockets with bulbs-all bulbs tested-good 216.) Driver's side lower dash trim 217.) SOLD-Passenger front seat outside chrome trim piece 218.) Front seat inner chrome trim pieces 219.) Power antenna-tested motor runs both directions-no mast 220.) Console carpet aluminum trim piece-passenger and driver 221.) Driver's side dash face aluminum-non AC car 222.) Shifter black plastic dust shield 223.) Passenger side upper dash trim 224.) Passenger side lower dash trim 226.) Console courtesy light brackets and attaching hardware 228.) Trunk lid hinge bolts 230.) Dash clock mounting bracket 231.) Firewall vacuum diaphragm mounting bracket and attaching hardware 232.) Console/sail panel courtesy light bezels 233.) Pair vent window cranks, plastic washers and attaching clips 234.) Deluxe interior passenger's side armrest end caps with attaching screws 235.) SOLD-Driver's seat outside trim chrome trim molding 236.) Driver's side upper dash trim 237.) SOLD-1965 speedometer lens and bezel 238.) 1963-1964 speedometer lens and bezel 239.) SOLD-1963-1964 gauge cluster lens and bezel 240.) Passenger seat stop lanyard and hardware 244.) Driver's front fender stainless trim molding 245.) Lower door stainless trim molding-will fit either door 246.) 1963 firewall to trunk ribbon wire harness-have 2-tested 247.) 1963 back seat rear speaker grill-also have speakers 248.) 4-way power seat slave track with 4 delrin glides 249.) Miscellaneous 4-way power seat pieces 250.) Set of 4 stainless headlight retainer rings 251.) Trunk lid latch with attaching hardware 252.) Trunk lid catch with attaching hardware 253.) 1963-1964 speedometer head with trip odometer cable-have 2 254.) 1965 speedometer head with trip odometer cable 256.) Passenger outside A-pillar stainless trim molding 257.) Passenger outside A-pillar stainless trim molding 258.) Console compartment lid hinge 259.) Driver's side rear quarter power window switch wiring harness 260.) Passenger's side rear quarter power window switch wiring harness 261.) Power steering pump brackets 262.) SOLD-Power steering pump with cap and pulley 263.) SOLD-Headliner pinchweld clips-whole and unbroken 264.) Passenger's side rear wheel opening molding 265.) Rear power window switches ribbon wiring harness-this is the ribbon harness that goes from the firewall to the rear switch harnesses 266.) Speedometer speed minder knob-have 4 267.) Deluxe interior armrest to door panel attaching hardware-have 2 sets 268.) Delco Remy starter 1107221 date code 3 E 14 Bench tested good 269.) SOLD-Delco Remy starter 1108392 date code 9 F 10 Bench tested good 270.) SOLD-1963 brake booster to intake manifold metal vacuum line with check valve 271.) Console compartment lid hinge 272.) Rear console light assembly 273.) 1963 1964 gauge cluster face with lenses-have 3 274.) Heater, AC & accessory switch lever knobs-have 8 275.) Used AC fuel pumps-have 3

According to the stats provided by Team Buick, the back spacing is 4 3/8". I can double check if you would like. Thanks. Bill

From what I have been told it fits 61-63 Buick with a Nailhead and Dynaflow.

I have for sale a Delco Remy 1107221 starter date code 3 E 14. Should fit 61-63 Buick from what I have been told. The starter has bench tested good. PM me if interested. Thanks. Bill

I have for sale a Delco Remy starter 1108392 with a date code of 9 F 10. Bench tested good. PM me if interested. Thanks. Bill

I am in central Wisconsin.

Here are pictures of the wheel cleaned up. It seems to be in pretty good condition. I know it will not work on our Rivieras but, someone here may know someone or someone may have another Buick this could work on. Make me an offer plus shipping. PM me if interested. Here are the specifics as per Team Buick. Thanks. Bill The wheel is 15" X 7" with a 5 X 4 3/4" bolt pattern. Design-8th Part Numbers-1236968 25504168 Years-1971-87 Rim Codes-903, 975 Appl. Code-WP, VJ Wheel Hub--2-1/8" Center Ring-Yes Center Cap Diam.-2-1/8" Back Space-4-3/8" Disc Brakes-Yes Bead Type-JJ Web Color-Black, satin

For sale is a Buick Rally/Road Wheel that was used on the 1971-1987 Buicks. The wheel is 15" X 7" with a 5 X 4 3/4" bolt pattern. The wheel seems to be in very nice condition. The chrome on the face has a pretty good shine and seems to be intact with a couple of spots of discoloration which are not noticeable unless under very close scrutiny. The black satin area could use a touch up. Overall a pretty nice wheel that can be used as it sits. Here are the stats on this wheel as per Team Buick. Design-8th Part Numbers-1236968 25504168 Years-1971-87 Rim Codes-903, 975 Appl. Code-WP, VJ Wheel Hub--2-1/8" Center Ring-Yes Center Cap Diam.-2-1/8" Back Space-4-3/8" Disc Brakes-Yes Bead Type-JJ Web Color-Black, satin Make me an offer plus shipping. PM me if interested. Thanks. Bill

Thanks for the info guys. I never thought to check bolt pattern. This explains why it was loose in the car and not mounted on the car with the other 3. Someone along the way bought the wrong wheel. Bill

I have a set of 4 Rally wheels which came with one of the 63 Rivieras I bought. Three of them are on one of the car and one was loose inside the car. The loose one that I brought home seems to be in pretty decent shape. I have not done an extensive search on the wheels for markings but, I did find some. Attached are pictures of the wheel and the stamped markings that I have found. If someone could help with deciphering those markings it would be greatly appreciated. The register hole is 2 1/8". Might there be other markings that I could look for? Is it possible to tell from the markings I have pictured what these wheels were originally from and what they would fit? Thanks. Cleaned up with better pictures below. Bill

In that forward left area of the trunk should be some electrical connectors for the various things in the rear. The trunk light connects into the circuit with the sail panel lights in that area. They both use an orange wire. I don't remember if the trunk light wire is hardwired in or if it has a plug at the end to go into a connector. As Ed said the trunk light is activated by a mercury switch in the lamp housing. Bill

UPDATED I have purchased two 1963 Rivieras and an assortment of miscellaneous parts. I will list some things here but, if there is something specific you are looking for PM me and I will see if I have what you are looking for. Thanks. 1.) 10 very nice right hand thread lug nuts 3.) Parking brake adjustment bracket and parking brake spring pin 4.) 2-1963 & 1964(?) standard interior rear quarter panel stainless trim pieces, enough for one side, can be used on either side 11.) Passenger side console plastic kick panel plate-I have 2 54.) 1965 console shifter bezel and shifter guide 57.) 1965 Front upper bumper brackets with attaching hardware 59.) 1965 lower front bumper support bar 68.) Console heater/AC air spring hose clamps 89.) Suction Throttle Valve bracket with attaching hardware 95.) 1965 front bumper filler panel/lower tie panel 105.) Blower motor-AC car-tested working 112.) 1965 Headlight Switch 118.) Driver's door long stainless beltline trim molding 119.) Upper cowl panel 122.) AC receiver/dehydrator brackets, clamps and attaching hardware 128.) Passenger side lower dash pad 130.) 4 access panel attaching clips-2 needed per panel 134.) Blower motor to firewall ground wire 136.) 1963 dash pad defroster grill with attaching hardware-I have 2 138.) 1965 speedometer cable with housing and connectors 141.) Master cylinder with screw on cap 144.) Air distribution duct that connects to evaporator 146.) 1965 Brake booster 148.) Throttle operating lever with throttle return spring 151.) Passenger's side rear quarter window stainless beltline trim molding 152.) Driver's side rear quarter window stainless beltline molding 155.) Passenger's door long stainless beltline trim molding 156.) Heater box with gasket 157.) SOLD-Miscellaneous 1965 horn and steering wheel components 160.) Inner fender door hinge cover filler panels-for car without electric windows 161.) Power Steering gear box 167.) 1963 left side dash access panel-have 2 168.) 1963-1965 rear seat below speaker filler panel-for back seat without a center armrest 171.) 1963-1965 middle lower rear seat filler panel 172.) Pair very nice 1963-1965 upper back seat side filler panels 173.) Rear quarter window leading edge weatherstrip stainless trim molding-have 3-will fit either side 174.) 1963-1965 deluxe interior door armrest pads-have 2-will fit either side 177.) Passenger side console kick panel extension-have 2 178.) Horn bracket with attaching hardware-for horn(s) behind grill 179.) SOLD-Pair console rear heat vents 180.) Passenger deluxe interior armrest power window switch bezel 181.) Driver deluxe interior armrest bezel with power windows and power seat 182.) Steering column ribbed aluminum trim for non-tilt wheel 183.) 1963 fuse box bracket 186.) Steering column support brackets 188.) 1965 trunk wiring harness 193.) 1963-1964 radio knobs 194.) 1963-1964 headlight switch knob, stem and bezels-have 2 sets 195.) SOLD-Two tone red steering wheel 198.) Passenger vent window beltline stainless trim molding-have 2 199.) Driver vent window beltline stainless trim molding-have 2 200.) Rear quarter stainless trim molding-will fit either side-have 2 201.) 1963-1964 Vacuum trunk release controller, actuator and mounting bracket-tested-working 202.) 1963-1964 Vacuum trunk release actuator-tested-working 203.) 1963-1965 4-way power seat-under seat wire harness-deluxe interior 204.) 4-way power seat motor-commutator bars cleaned and sanded smooth-shaft relubed-tested-runs smoothly both directions 205.) 4-way power seat transmission-completely cleaned, degreased and relubed 206.) Standard interior door armrest pads 207.) Power window wiring harness-passenger door-deluxe interior (work for standard interior?) 209.) 1963 Glovebox door script 210.) Turn signal and high beam lenses and assembly-1 left 211.) 1965 lighter element and knob 212.) 1963 heater/AC switch dash cover plate 213.) 1963 glovebox light and lens 215.) Complete set dash cluster light sockets with bulbs-all bulbs tested-good 216.) Driver's side lower dash trim 217.) Passenger front seat outside chrome trim piece 218.) Front seat inner chrome trim piece 219.) Power antenna-tested motor runs both directions-no mast 220.) Console carpet trim piece-passenger and driver 221.) Driver's side dash face aluminum-non AC car 222.) Shifter black plastic dust shield 223.) Passenger side upper dash trim 224.) Passenger side lower dash trim 226.) Console courtesy light brackets and attaching hardware 228.) Trunk lid hinge bolts 230.) Dash clock mounting bracket 231.) Firewall vacuum diaphragm mounting bracket and attaching hardware 232.) Console/sail panel courtesy light bezels 233.) Pair vent window cranks, plastic washers and attaching clips 234.) Deluxe interior passenger's side armrest end caps with attaching screws 235.) Driver's seat outside trim chrome trim molding 236.) Driver's side upper dash trim 237.) 1965 speedometer lens and bezel 238.) 1963-1964 speedometer lens and bezel 239.) 1963-1964 gauge cluster lens and bezel 240.) Passenger seat stop lanyard and hardware 244.) Driver's front fender stainless trim molding 245.) Lower door stainless trim molding 246.) 1963 firewall to trunk ribbon wire harness-have 2-tested 247.) 1963 back seat rear speaker grill-also have speakers 248.) 4-way power seat slave track with 4 delrin glides 249.) Miscellaneous 4-way power seat pieces 250.) Set of 4 stainless headlight retainer rings 251.) Trunk lid latch with attaching hardware 252.) Trunk lid catch with attaching hardware 253.) 1963-1964 speedometer head with trip odometer cable-have 2 254.) 1965 speedometer head with trip odometer cable 256.) Passenger outside A-pillar stainless trim molding 257.) Passenger outside A-pillar stainless trim molding 258.) Console compartment lid hinge 259.) Driver's side rear quarter power window switch wiring harness 260.) Passenger's side rear quarter power window switch wiring harness 261.) Power steering pump brackets 262.) Power steering pump with cap and pulley 263.) SOLD-Headliner pinchweld clips-whole and unbroken 264.) Passenger's side rear wheel opening molding 265.) Rear power window switches ribbon wiring harness-this is the ribbon harness that goes from the firewall to the rear switch harnesses

Chuck, I am with you on that one. One of my goals in life is to never drive through Chicago again for the rest of my life. I hope to see you and your car in Kalamazoo. Bill

No, this is the high speed ferry, the Lake Express that goes from Milwaukee to Muskegon. Leaving at 12:30 P.M on the 21st and coming back at 10:15 A.M. on the 25th. Should be plenty of light on both trips. Bill

My brother-in-law and I will be making the trip to Kalamazoo this year. We have decided to take the Lake Express Ferry across Lake Michigan. We will be hooking up with another ROA member from Minnesota and his wife for the drive and ferry ride across the lake. The ferry ride is not cheap but, it does make for a scenic and relaxing interlude on the trip and cuts a lot of travel time off of the drive if you are coming from an area west of Michigan. Another huge bonus is no drive through Chicago. If anyone else is interested in joining up with us for the journey PM me and I can give you the particulars. If not, we will see you in Kalamazoo! Bill

UPDATED I have purchased two 1963 Rivieras and an assortment of miscellaneous parts. I will list some things here but, if there is something specific you are looking for PM me and I will see if I have what you are looking for. Thanks. 1.) 10 very nice right hand thread lug nuts 3.) Parking brake adjustment bracket and parking brake spring pin 4.) 2-1963 & 1964(?) standard interior rear quarter panel stainless trim pieces, enough for one side, can be used on either side 11.) Passenger side console plastic kick panel plate-I have 2 54.) 1965 console shifter bezel and shifter guide 57.) 1965 Front upper bumper brackets with attaching hardware 59.) 1965 lower front bumper support bar 68.) Console heater/AC air hose clamps 89.) Suction Throttle Valve bracket with attaching hardware 95.) 1965 front bumper filler panel/lower tie panel 105.) Blower motor-AC car-tested working 112.) 1965 Headlight Switch 118.) Driver's door long stainless beltline trim molding 119.) Upper cowl panel 122.) AC receiver/dehydrator brackets, clamps and attaching hardware 128.) Passenger side lower dash pad 130.) 4 access panel attaching clips-2 needed per panel 134.) Blower motor to firewall ground wire 136.) 1963 dash pad defroster grill with attaching hardware-I have 2 138.) 1965 speedometer cable with housing and connectors 141.) Master cylinder with screw on cap 144.) Air distribution duct that connects to evaporator 145.) SOLD-1964-1965 brake pedal assembly with brake light switch-use to convert 1963 to pedal switch 146.) 1965 Brake booster 147.) SOLD-AC muffler 148.) Throttle operating lever with throttle return spring 151.) Passenger's side rear quarter window stainless beltline trim molding 152.) Driver's side rear quarter window stainless beltline molding 155.) Passenger's door long stainless beltline trim molding 156.) Heater box with gasket 157.) Miscellaneous 1965 horn and steering wheel components 160.) Inner fender door hinge cover filler panels-for car without electric windows 161.) Power Steering gear box 164.) SOLD-1963 rear defroster dash wiring harness-needed if your car was manufactured before March 1, 1963-rare 167.) 1963 left side dash access panel-have 2 168.) 1963-1965 rear seat below speaker filler panel-for back seat without a center armrest 171.) 1963-1965 middle lower rear seat filler panel 172.) Pair very nice 1963-1965 upper back seat side filler panels 173.) Rear quarter window leading edge weatherstrip stainless trim molding-have 3-will fit either side 174.) 1963-1965 deluxe interior door armrest pads-have 2-will fit either side 177.) Passenger side console kick panel extension-have 2 178.) Horn bracket with attaching hardware-for horn(s) behind grill 179.) Pair console rear heat vents 180.) Passenger deluxe interior armrest power window switch bezel 181.) Driver deluxe interior armrest bezel with power windows and power seat 182.) Steering column ribbed aluminum trim for non-tilt wheel 183.) 1963 fuse box bracket 186.) Steering column support brackets 187.) SOLD-Engine compartment heater hose brackets 188.) 1965 trunk wiring harness 193.) 1963-1964 radio knobs 194.) 1963-1964 headlight switch knob, stem and bezels-have 2 sets 195.) Two tone red steering wheel 196.) SOLD-Passenger fender stainless trim molding 198.) Passenger vent window beltline stainless trim molding-have 2 199.) Driver vent window beltline stainless trim molding-have 2 200.) Rear quarter stainless trim molding-will fit either side-have 2 201.) 1963-1964 Vacuum trunk release controller, actuator and mounting bracket-tested-working 202.) 1963-1964 Vacuum trunk release actuator-tested-working 203.) 1963-1965 4-way power seat-under seat wire harness-deluxe interior 204.) 4-way power seat motor-commutator bars cleaned and sanded smooth-shaft relubed-tested-runs smoothly both directions 205.) 4-way power seat transmission-completely cleaned, degreased and relubed 206.) Standard interior door armrest pads 207.) Power window wiring harness-passenger door-deluxe interior (work for standard interior?) 208.) SOLD-Power window switch-passenger door-deluxe interior 209.) 1963 Glovebox door script 210.) Turn signal and high beam lenses and assembly-have 2 211.) 1965 lighter element and knob 212.) 1963 heater/AC switch dash cover plate 213.) 1963 glovebox light and lens 214.) SOLD-4-way power seat rubber coupler 215.) Complete set dash cluster light sockets with bulbs-all bulbs tested-good 216.) Driver's side lower dash trim 217.) Passenger front seat outside chrome trim piece 218.) Front seat inner chrome trim piece 219.) Power antenna-tested motor runs both directions-no mast 220.) Console carpet trim piece-passenger and driver 221.) Driver's side dash face aluminum-non AC car 222.) Shifter black plastic dust shield 223.) Passenger side upper dash trim 224.) Passenger side lower dash trim 225.) SOLD-1963 shifter lens 226.) Console courtesy light brackets and attaching hardware 227.) SOLD-Dimmer switch carpet grommet 228.) Trunk lid hinge bolts 229.) SOLD-Firewall steering column pass through rubber grommet, plate and bolts 230.) Dash clock mounting bracket 231.) Firewall vacuum diaphragm mounting bracket and attaching hardware 232.) Console/sail panel courtesy light bezels 233.) Pair vent window cranks, plastic washers and attaching clips 234.) Deluxe interior passenger's side armrest end caps with attaching screws 235.) Driver's seat outside trim chrome trim molding 236.) Driver's side upper dash trim 237.) 1965 speedometer lens and bezel 238.) 1963-1964 speedometer lens and bezel 239.) 1963-1964 gauge cluster lens and bezel 240.) Passenger seat stop lanyard and hardware 241.) SOLD-Accessory/courtesy light switch with knob-tested 242.) SOLD-Passenger outside A-pillar stainless trim molding 243.) SOLD-Driver outside A-pillar stainless trim molding 244.) Driver's front fender stainless trim molding 245.) Lower door stainless trim molding 246.) 1963 firewall to trunk ribbon wire harness-have 2-tested 247.) 1963 back seat rear speaker grill-also have speakers 248.) 4-way power seat slave track with 4 delrin glides 249.) Miscellaneous 4-way power seat pieces 250.) Set of 4 stainless headlight retainer rings 251.) Trunk lid latch with attaching hardware 252.) Trunk lid catch with attaching hardware 253.) 1963-1964 speedometer head with trip odometer cable-have 3 254.) 1965 speedometer head with trip odometer cable 255.) SOLD-1963 Dynaflow dipstick and dipstick tube

UPDATED I have recently purchased two 1963 Rivieras and an assortment of miscellaneous parts. I will list some things here but, if there is something specific you are looking for PM me and I will see if I have what you are looking for. Thanks. 1.) 10 very nice right hand thread lug nuts 3.) Parking brake adjustment bracket and parking brake spring pin 4.) 2-1963 & 1964(?) standard interior rear quarter panel stainless trim pieces, enough for one side, can be used on either side 11.) Passenger side console plastic kick panel plate-I have 2 54.) 1965 console shifter bezel and shifter guide 57.) 1965 Front upper bumper brackets with attaching hardware 59.) 1965 lower front bumper support bar 68.) Console heater/AC air hose clamps 89.) Suction Throttle Valve bracket with attaching hardware 95.) 1965 front bumper filler panel/lower tie panel 105.) Blower motor-AC car-tested working 112.) 1965 Headlight Switch 118.) Driver's door long stainless beltline trim molding 119.) Upper cowl panel 122.) AC receiver/dehydrator brackets, clamps and attaching hardware 128.) Passenger side lower dash pad 130.) 4 access panel attaching clips-2 needed per panel 134.) Blower motor to firewall ground wire 136.) 1963 dash pad defroster grill with attaching hardware-I have 2 138.) 1965 speedometer cable with housing and connectors 141.) Master cylinder with screw on cap 144.) Air distribution duct that connects to evaporator 145.) SOLD-1964-1965 brake pedal assembly with brake light switch-use to convert 1963 to pedal switch 146.) 1965 Brake booster 147.) AC muffler 148.) Throttle operating lever with throttle return spring 151.) Passenger's side rear quarter window stainless beltline trim molding 152.) Driver's side rear quarter window stainless beltline molding 155.) Passenger's door long stainless beltline trim molding 156.) Heater box with gasket 157.) Miscellaneous 1965 horn and steering wheel components 160.) Inner fender door hinge cover filler panels-for car without electric windows 161.) Power Steering gear box 164.) SOLD-1963 rear defroster dash wiring harness-needed if your car was manufactured before March 1, 1963-rare 167.) 1963 left side dash access panel-have 2 168.) 1963-1965 rear seat below speaker filler panel-for back seat without a center armrest 171.) 1963-1965 middle lower rear seat filler panel 172.) Pair very nice 1963-1965 upper back seat side filler panels 173.) Rear quarter window leading edge weatherstrip stainless trim molding-have 3-will fit either side 174.) 1963-1965 deluxe interior door armrest pads-have 2-will fit either side 177.) Passenger side console kick panel extension-have 2 178.) Horn bracket with attaching hardware-for horn(s) behind grill 179.) Pair console rear heat vents 180.) Passenger deluxe interior armrest power window switch bezel 181.) Driver deluxe interior armrest bezel with power windows and power seat 182.) Steering column ribbed aluminum trim for non-tilt wheel 183.) 1963 fuse box bracket 186.) Steering column support brackets 187.) Engine compartment heater hose brackets 188.) 1965 trunk wiring harness 193.) 1963-1964 radio knobs 194.) 1963-1964 headlight switch knob, stem and bezels-have 2 sets 195.) Two tone red steering wheel 196.) SOLD-Passenger fender stainless trim molding 198.) Passenger vent window beltline stainless trim molding-have 2 199.) Driver vent window beltline stainless trim molding-have 2 200.) Rear quarter stainless trim molding-will fit either side-have 2 201.) 1963-1964 Vacuum trunk release controller, actuator and mounting bracket-tested-working 202.) 1963-1964 Vacuum trunk release actuator-tested-working 203.) 1963-1965 4-way power seat-under seat wire harness-deluxe interior 204.) 4-way power seat motor-commutator bars cleaned and sanded smooth-shaft relubed-tested-runs smoothly both directions 205.) 4-way power seat transmission-completely cleaned, degreased and relubed 206.) Standard interior door armrest pads 207.) Power window wiring harness-passenger door-deluxe interior (work for standard interior?) 208.) SOLD-Power window switch-passenger door-deluxe interior 209.) 1963 Glovebox door script 210.) Turn signal and high beam lenses and assembly-have 3 211.) 1965 lighter element and knob 212.) 1963 heater/AC switch dash cover plate 213.) 1963 glovebox light and lens 214.) SOLD-4-way power seat rubber coupler 215.) Complete set dash cluster light sockets with bulbs-all bulbs tested-good 216.) Driver's side lower dash trim 217.) Passenger front seat outside chrome trim piece 218.) Front seat inner chrome trim piece 219.) Power antenna-tested motor runs both directions-no mast 220.) Console carpet trim piece-passenger and driver 221.) Driver's side dash face aluminum-non AC car 222.) Shifter black plastic dust shield 223.) Passenger side upper dash trim 224.) Passenger side lower dash trim 225.) SOLD-1963 shifter lens 226.) Console courtesy light brackets and attaching hardware 227.) SOLD-Dimmer switch carpet grommet 228.) Trunk lid hinge bolts 229.) SOLD-Firewall steering column pass through rubber grommet, plate and bolts 230.) Dash clock mounting bracket 231.) Firewall vacuum diaphragm mounting bracket and attaching hardware 232.) Console/sail panel courtesy light bezels 233.) Pair vent window cranks, plastic washers and attaching clips 234.) Deluxe interior passenger's side armrest end caps with attaching screws 235.) Driver's seat outside trim chrome trim molding 236.) Driver's side upper dash trim 237.) 1965 speedometer lens and bezel 238.) 1963-1964 speedometer lens and bezel 239.) 1963-1964 gauge cluster lens and bezel 240.) Passenger seat stop lanyard and hardware 241.) SOLD-Accessory/courtesy light switch with knob-tested 242.) SOLD-Passenger outside A-pillar stainless trim molding 243.) SOLD-Driver outside A-pillar stainless trim molding 244.) Driver's front fender stainless trim molding 245.) Lower door stainless trim molding 246.) 1963 firewall to trunk ribbon wire harness-have 2-tested 247.) 1963 back seat rear speaker grill-also have speakers 248.) 4-way power seat slave track with 4 delrin glides 249.) Miscellaneous 4-way power seat pieces 250.) Set of 4 stainless headlight retainer rings

My 1963 is ready to turn 86,000 miles on the odometer. This last year I would occasionally get the oil light coming on when idling in gear. It doesn't happen all the time and it would happen after a long stretch of driving when everything was good and hot. I talked this over with Tom T. and he told me that this was a sign that my engine is starting to show a little wear. He suggested to me to switch to a 20W-50 oil. I did this and I have not experienced this problem since. A couple of years ago I had switched to Lucas Classic and Hot Rod Oil. I was using their 10W-30 and then switched to their 20W-50. Both weights have a zinc content of 2100 ppm. I am very happy with their oil. I also like the fact that I can get this oil at several of the chain auto parts stores and on Amazon. Bill

I bought and received it several months ago. Got it in 2-3 days back then. I was just reporting that had I bought my last one on Amazon to give others interested another possible option for purchase, not that I had just ordered it. At the time I was writing the post I went on Amazon to double check what brand (Wix) and number (42092) that I had purchased and I also checked to see if they were still available/selling them at this time. Which they were. Bill

UPDATED I have recently purchased two 1963 Rivieras and an assortment of miscellaneous parts. I will list some things here but, if there is something specific you are looking for PM me and I will see if I have what you are looking for. Thanks. 1.) 10 very nice right hand thread lug nuts 3.) Parking brake adjustment bracket and parking brake spring pin 4.) 2-1963 & 1964(?) standard interior rear quarter panel stainless trim pieces, enough for one side, can be used on either side 11.) Passenger side console plastic kick panel plate-I have 2 54.) 1965 console shifter bezel and shifter guide 57.) 1965 Front upper bumper brackets with attaching hardware 59.) 1965 lower front bumper support bar 68.) Console heater/AC air hose clamps 89.) Suction Throttle Valve bracket with attaching hardware 95.) 1965 front bumper filler panel/lower tie panel 105.) Blower motor-AC car-tested working 112.) 1965 Headlight Switch 118.) Driver's door long stainless beltline trim molding 119.) Upper cowl panel 122.) AC receiver/dehydrator brackets, clamps and attaching hardware 128.) Passenger side lower dash pad 130.) 4 access panel attaching clips-2 needed per panel 134.) Blower motor to firewall ground wire 136.) 1963 dash pad defroster grill with attaching hardware-I have 2 138.) 1965 speedometer cable with housing and connectors 141.) Master cylinder with screw on cap 144.) Air distribution duct that connects to evaporator 145.) 1964-1965 brake pedal assembly with brake light switch-use to convert 1963 to pedal switch 146.) 1965 Brake booster 147.) AC muffler 148.) Throttle operating lever with throttle return spring 151.) Passenger's side rear quarter window stainless beltline trim molding 152.) Driver's side rear quarter window stainless beltline molding 155.) Passenger's door long stainless beltline trim molding 156.) Heater box with gasket 157.) Miscellaneous 1965 horn and steering wheel components 160.) Inner fender door hinge cover filler panels-for car without electric windows 161.) Power Steering gear box 164.) 1963 rear defroster dash wiring harness-needed if your car was manufactured before March 1, 1963-rare 167.) 1963 left side dash access panel-have 2 168.) 1963-1965 rear seat below speaker filler panel-for back seat without a center armrest 171.) 1963-1965 middle lower rear seat filler panel 172.) Pair very nice 1963-1965 upper back seat side filler panels 173.) Rear quarter window leading edge weatherstrip stainless trim molding-have 3-will fit either side 174.) 1963-1965 deluxe interior door armrest pads-have 2-will fit either side 177.) Passenger side console kick panel extension-have 2 178.) Horn bracket with attaching hardware-for horn(s) behind grill 179.) Pair console rear heat vents 180.) Passenger deluxe interior armrest power window switch bezel 181.) Driver deluxe interior armrest bezel with power windows and power seat 182.) Steering column ribbed aluminum trim for non-tilt wheel 183.) 1963 fuse box bracket 186.) Steering column support brackets 187.) Engine compartment heater hose brackets 188.) 1965 trunk wiring harness 193.) 1963-1964 radio knobs 194.) 1963-1964 headlight switch knob, stem and bezels-have 2 sets 195.) Two tone red steering wheel 196.) SOLD-Passenger fender stainless trim molding 198.) Passenger vent window beltline stainless trim molding-have 2 199.) Driver vent window beltline stainless trim molding-have 2 200.) Rear quarter stainless trim molding-will fit either side-have 2 201.) 1963-1964 Vacuum trunk release controller, actuator and mounting bracket-tested-working 202.) 1963-1964 Vacuum trunk release actuator-tested-working 203.) 1963-1965 4-way power seat-under seat wire harness-deluxe interior 204.) 4-way power seat motor-commutator bars cleaned and sanded smooth-shaft relubed-tested-runs smoothly both directions 205.) 4-way power seat transmission-completely cleaned, degreased and relubed 206.) Standard interior door armrest pads 207.) Power window wiring harness-passenger door-deluxe interior (work for standard interior?) 208.) SOLD-Power window switch-passenger door-deluxe interior 209.) 1963 Glovebox door script 210.) Turn signal and high beam lenses and assembly-have 4 211.) 1965 lighter element and knob 212.) 1963 heater/AC switch dash cover plate 213.) 1963 glovebox light and lens 214.) 4-way power seat rubber coupler 215.) Complete set dash cluster light sockets with bulbs-all bulbs tested-good 216.) Driver's side lower dash trim 217.) Passenger front seat outside chrome trim piece 218.) Front seat inner chrome trim piece 219.) Power antenna-tested motor runs both directions-no mast 220.) Console carpet trim piece-passenger and driver 221.) Driver's side dash face aluminum-non AC car 222.) Shifter black plastic dust shield 223.) Passenger side upper dash trim 224.) Passenger side lower dash trim 225.) SOLD-1963 shifter lens 226.) Console courtesy light brackets and attaching hardware 227.) SOLD-Dimmer switch carpet grommet 228.) Trunk lid hinge bolts 229.) Firewall steering column pass through rubber grommet, plate and bolts 230.) Dash clock mounting bracket 231.) Firewall vacuum diaphragm mounting bracket and attaching hardware 232.) Console/sail panel courtesy light bezels 233.) Pair vent window cranks, plastic washers and attaching clips 234.) Deluxe interior passenger's side armrest end caps with attaching screws 235.) Driver's seat outside trim chrome trim molding 236.) Driver's side upper dash trim 237.) 1965 speedometer lens and bezel 238.) 1963-1964 speedometer lens and bezel 239.) 1963-1964 gauge cluster lens and bezel 240.) Passenger seat stop lanyard and hardware 241.) SOLD-Accessory/courtesy light switch with knob-tested 242.) SOLD-Passenger outside A-pillar stainless trim molding 243.) SOLD-Driver outside A-pillar stainless trim molding 244.) Driver's front fender stainless trim molding 245.) Lower door stainless trim molding

Tan outer trim piece and rear 1963 outer trim bracket still available.

Yes and that has no bearing on the fact that I bought my last one there. Nor does it change the fact that they are still available. Your point is? Bill