30dodge35

Are we sure it was the navigator giving wrong direction? Or operator! 36 LC has a nice set of car hupcap on it, Wally looking for a truck set, you got any

Fallbrook, California, June 17 to June 23 2017, in-between San Diego and LA .

Do you have book of info on 26?

Math, glad you made it back home and didn't have those problem in NJ on compressions problem , put a couple squirt in cylinder and retest, if it comes up you may have ring problem , if same vale problem , use a Differential tester, it has 2 gages, with piston on top of compression stroke apply shop air, the you can listen to escaping air, either from exhaust or intake, if this is problem, take side panel for adjustment off you can move valve up and down with a screw driver to see if valve is sticking, should have clearance on cam. if still low pull head, take a look at valve seat with valve up, off seat, tom Meyers has new valves, on rear end overfilling, use 1200 weight in transmission, don't overfill, if still flowing to back, seal is bad on rear of transmission and seal on wheel. jesse

Well made to Miridam Mississippi 1089 miles about 320 more no problems Big dodge running great , 30 being a good trailer queen

Great meet still traveling home about Haveway

Bob your bows are loaded on trailer

I am going, bring 1930 DA, and wife, also Ethan , my Granson,

Who is going to DodgeBrothers National meet in Budd Lake, NJ. What are you driving or bringing?

Sorry you lost me on that last response

Dave, the 36 in video has correct wheel, 16 inch Plymouth wheel

36 in video has 16 inch wheels , correct wheels and hubcap

10 scallops,. 16 inch wheel, 12 scallops, 17 inches i use a 16 for spare, , because I use larger 700 i, fill wheel better,

The other part, is hupcap so, when I had 16 car rims on 35' I had to have the car hubcaps with raise dodge v,. Due to the fact the front offset is not enough, you have to have the 3 inch high hubcap for spindle clearance, sold the set I had to Dan,

By the chart the Canadian was a wider rim 5.25. 2 inches wider,

Looking good, I have A spare Distrubutor for my truck and car , with them at all times,

Well, I am back on project, rough out two sets of bows today, 1" by 1 1/2" Bob, hopefully,I will have your set steam bent, and bring to New Jersey, I will try to do 2 sets and bring with me to Budd lake,

The 16 were actually Plymouth wheels used on the 35, trucks,they are 2 piece rivet like in the picture, are actually stronger design then the 16 on cars, I had the car type on the truck when I first restored it,. Then swap a set of rims with Dan Kerr for truck, Plymouth type,. Put new tires a tubes,. Then a guy in Missouri was hotroding a 35 , bought 17 from him, got engine , transmission reared and rims, for $1000, also use different hupcap, Hotrodder are go for something,. SPARE PARTS!

This the brochure for 35, may be same for 36,

the wheels on my truck or 17, they are the 2 piece type, the ones in the picture look like the type used on cars , the scallops are different

You might check around with truck rentals ,. Enterprise has a weekly rate 400, have to be 25,. But there may be others

Don't know radius, haven't measured, bend to same as old bows,

Clean the stud hole, use blue lock tite , thread lock,. Then on surface aviation permatex, black and guey sticks to everything ,lighten coat case and light coat on gasket, install on case ,

I haven't made them yet, just got thru with bill's. I will make a set and bring with me to New Jersey, I need to put them against another car, to make sure bend and radius is correct,. They will not be tapered on ends, you will have to fit to your sockets, pm me if interested

now that all 4 bows are bent start tapering ends to length utilizing old bows, I built fixture to hold frame at correct angle Will adjust on Car