Buickboy58 Posted May 9, 2022 Share Posted May 9, 2022 Hi all, on my 58, 364, the engine stall when I take off from a stop sign or traffic light. Yesterday, I went out for a drive and It started well, let it warm up a little then drove it until I stop at the traffic, the engine stalled when I was pressing the gas pedal, I restarted the motor and kept doing this every time I would stop for traffic light and even slowing down to almost stopping then re-accelerate, it wanted to stall if press the gas pedal. I have a Quickfuel carb, 4b, 650 cfm, electric fuel pump, electronic ignition. New spark plugs and wires. It was running fine last fall when I put it away for the winter in my garage, and this happen when I wanted to put it back on the road. I did put some fuel stabilizer before I stored it. Any idea what could be the problem. Thanks Link to comment Share on other sites More sharing options...
usnavystgc Posted May 9, 2022 Share Posted May 9, 2022 It sounds like an accellerator pump issue. 2 Link to comment Share on other sites More sharing options...
JohnD1956 Posted May 9, 2022 Share Posted May 9, 2022 Did you store it with ethanol free gas and a full tank? Link to comment Share on other sites More sharing options...
NTX5467 Posted May 10, 2022 Share Posted May 10, 2022 As you have an aftermarket carb on the engine, what is the hot base idle speed set at? Link to comment Share on other sites More sharing options...
Buickboy58 Posted May 10, 2022 Author Share Posted May 10, 2022 7 hours ago, JohnD1956 said: Did you store it with ethanol free gas and a full tank? full tank, regular gas. Link to comment Share on other sites More sharing options...
Buickboy58 Posted May 10, 2022 Author Share Posted May 10, 2022 18 minutes ago, NTX5467 said: As you have an aftermarket carb on the engine, what is the hot base idle speed set at? I don't have a rpm gauge but I would say it around 700-750 rpm. Link to comment Share on other sites More sharing options...
Buickboy58 Posted May 10, 2022 Author Share Posted May 10, 2022 8 hours ago, usnavystgc said: It sounds like an accellerator pump issue. That's what I think, I will remove the carb tomorrow and check it out. Thanks Link to comment Share on other sites More sharing options...
Buickboy58 Posted May 10, 2022 Author Share Posted May 10, 2022 10 hours ago, Buickboy58 said: Hi all, on my 58, 364, the engine stall when I take off from a stop sign or traffic light. Yesterday, I went out for a drive and It started well, let it warm up a little then drove it until I stop at the traffic, the engine stalled when I was pressing the gas pedal, I restarted the motor and kept doing this every time I would stop for traffic light and even slowing down to almost stopping then re-accelerate, it wanted to stall if press the gas pedal. I have a Quickfuel carb, 4b, 650 cfm, electric fuel pump, electronic ignition. New spark plugs and wires. It was running fine last fall when I put it away for the winter in my garage, and this happen when I wanted to put it back on the road. I did put some fuel stabilizer before I stored it. Any idea what could be the problem. Thanks Yesterday It's started, but this morning no luck, it wouldn't start at all. The engine is just cranking. Link to comment Share on other sites More sharing options...
NTX5467 Posted May 10, 2022 Share Posted May 10, 2022 Need to determine the idle rpm with a tachometer to make sure where things are. Condition of spark plugs? Gap? Points? And especially the coil? The accel pump can be checked on the engine, no disassembly required. Remove the air cleaner and move the throttle linkage and look for the "shot" from the nozzle in the center of the primary throttle bores, upstream from the venturi cluster. The Holley pumps are very responsive to throttle movement. NTX5467 Link to comment Share on other sites More sharing options...
60s GM Fan Posted May 10, 2022 Share Posted May 10, 2022 Fuel pump not strong enough? Link to comment Share on other sites More sharing options...
Buickboy58 Posted May 10, 2022 Author Share Posted May 10, 2022 Thanks, I found out what was the problem, I have a Cool Carb plate that cut the heat from going under the carb and create vapor lock. I had it installed right on top of the adapter spacer over the intake but I move it up last weekend just under the carb I notice that it was just under the accelerator pump but didn't realize that there is a lever underneath that need to move, well it wasn't moving at all because it was touching the Cool Carb plate, so I removed the carb, the plate and made a slot inside to free the lever and it fix the problem. Thanks for your input. 5 3 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now