engine swaps Posted July 10, 2019 Share Posted July 10, 2019 will a spitfire engine and fluid drive transmission from a 1947 Chrysler work in a 1941 Chrysler without a lot of modifications? thanks bob Link to comment Share on other sites More sharing options...
Rusty_OToole Posted July 11, 2019 Share Posted July 11, 2019 Shouldn't be too much trouble if they are both six cylinders. Especially if you have the 47 car to take parts off of. Did the 41 have a vacuum or hydraulic trans? There may be some small differences but nothing a good mechanic with a manual can't handle. Link to comment Share on other sites More sharing options...
Spinneyhill Posted July 11, 2019 Share Posted July 11, 2019 Drive shaft length might be a problem. Link to comment Share on other sites More sharing options...
c49er Posted July 11, 2019 Share Posted July 11, 2019 (edited) The trans in a 1941 is the M-4 Vacamatic... the 47 is the M-5 hydraulically operated transmission. That's a problem as the vacuum/electrical controls and shifter rods, control cable etc.differ a lot. Using the M-4 on the 47 Engine would be a good idea. Also the throttle linkage is mounted different. You would need both engines and Transmissions side by side to do a swap properly. Edited July 11, 2019 by c49er (see edit history) Link to comment Share on other sites More sharing options...
engine swaps Posted July 11, 2019 Author Share Posted July 11, 2019 thanks to the 3 of you am new to this and appreciate it very much Link to comment Share on other sites More sharing options...
Rusty_OToole Posted July 11, 2019 Share Posted July 11, 2019 C49er how different are the M4 and M6 cars? I have not worked on an M4 but the M6 models have 2 shifter rods to the trans, plus a simple wiring harness, special carburetor, and a little box with a resistor and a circuit breaker. Then the trans has the handbrake and speedo cable. The only sticky point would be the shift rods, everything else transfers over. I am ignoring for the moment things like motor mounts, radiator connections, carb linkage which should not be insurmountable. Link to comment Share on other sites More sharing options...
Rusty_OToole Posted July 11, 2019 Share Posted July 11, 2019 (edited) Then again this might be one of those cases where the questioner is asking the wrong question. Beginners have a habit of assuming it is easier to swap engines than to fix one. Unless the 41 engine and trans is missing, or the rod is sticking thru the block, it would probably be easier to fix it . OP also fails to state whether it is a six cylinder car or an eight cylinder car. What the hell, they are all the same aren't they (nope). Edited July 11, 2019 by Rusty_OToole (see edit history) Link to comment Share on other sites More sharing options...
engine swaps Posted July 12, 2019 Author Share Posted July 12, 2019 since I am abeginner I assumed it would just be easier to swap engines the fluid drive in the 41 is fine but the problem is the engine and I haven't seen an ad for rebuilding one if you know of a rebuilder I would like to know bob Link to comment Share on other sites More sharing options...
Rusty_OToole Posted July 14, 2019 Share Posted July 14, 2019 They are a pretty simple engine and all parts are available. If there is an engine rebuilder or auto machine shop in your town they should be able to handle it. If not, ask around and find out where the old car guys take their engine work. Vintage Power Wagons in Iowa sells all kinds of parts, since Dodge Power Wagons used the same engine. Last time I looked they had NOS pistons, $65 for a set of 6. How good do you want it? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now