rjp Posted May 17, 2019 Share Posted May 17, 2019 looking for two rear brake drums , 7 hole 130 to 145 series (I think) Link to comment Share on other sites More sharing options...
Scott in PA Posted May 17, 2019 Share Posted May 17, 2019 I think I have those, Roger. I'll check tomorrow and text you. Link to comment Share on other sites More sharing options...
PFitz Posted May 17, 2019 Share Posted May 17, 2019 (edited) Roger, Are you aware that the club sells new drums for 29 - 32 to rivet onto your hubs. They are slightly thicker and stronger than originals., If your swapping drums with hubs still attached there's a difference in 29 verses later hubs and how they fit with the wheel bearings and seals.. So, which do you need, 130 or 145 because they are not the same hubs. Paul Edited May 17, 2019 by PFitz (see edit history) Link to comment Share on other sites More sharing options...
rjp Posted May 18, 2019 Author Share Posted May 18, 2019 This car has a newer rear end under it. How can I teal what year or model it really is ? I don't see any numbers on it. Link to comment Share on other sites More sharing options...
rjp Posted May 18, 2019 Author Share Posted May 18, 2019 If Ed Joy has a old drum to see if what I want to do will work ,I like the sound of the new drums. We will see. The person before me welded spacers and ahome made adaptor for the wire wheels Link to comment Share on other sites More sharing options...
PFitz Posted May 18, 2019 Share Posted May 18, 2019 (edited) Check the aluminum differential casting.... there should be a casting date on top viewed with a mirror. And the gear ratio will be stamped into the rear face of the aluminum flange where the passenger side axle tube joins it. It's stamped in the form of a fraction. Divide the bottom number by the top number to get the ratio. The 29 and earlier use a single outer wheel bearing and have to have the cast iron seal retainer machined to accept a modern seal, or shim the original seal back to a snug fit. For 1930 they went to a rear axle with two tapered opposed outer wheel bearings and a stamped sheet metal seal retainer that will accept a modern press-fit lip seal. Both the bearings and seal are a size that modern equivalents are available new. Paul Edited May 18, 2019 by PFitz (see edit history) 1 Link to comment Share on other sites More sharing options...
rjp Posted May 19, 2019 Author Share Posted May 19, 2019 Looked at the rea end, the only casting no. I see is 34845. Don't see any thing else at this time. Link to comment Share on other sites More sharing options...
PFitz Posted May 19, 2019 Share Posted May 19, 2019 (edited) Ok, lets try this way. The brake backing plate attaches to a tapered casting that is welded onto the outboard end of the axle tube called the "brake carrier". That casting also contains the wheel bearing and seal. Measuring from the backing plate toward the differential, that tapered casting should be about 5-1/8 inch long if it's a 1930 or later double wheel bearing rear axle (drawing 45487). If the tapered casting is about 3-13/16 inches long than it's a 1928 or 29 single wheel bearing axle (drawing 36010). Note, the 28 brake drums are a dished shape, so the new drums won't fit on properly in relation to the brake shoes. Paul Edited May 19, 2019 by PFitz (see edit history) 1 Link to comment Share on other sites More sharing options...
rjp Posted May 20, 2019 Author Share Posted May 20, 2019 Paul, I finds the date with a lot of cleaning and a new mirror, 7-11-9. So is that good or bad? Still trying to find rear houk wheel adaptors, might not be possible. Link to comment Share on other sites More sharing options...
PFitz Posted May 20, 2019 Share Posted May 20, 2019 Roger, July 11 1929. That could be a later production 29 or an early 30. Obviously, the castings runs would be made long before the car. And the first production cars came out in the later part of the previous year. I've seen an early production 31 with a July of 30 differential casting date. To be sure, measure the brake carrier tapered length and see if it matches either of the measurements in my last post. 29 or30, the good news is that it will take the new brake drums. Paul Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now