V10 Posted August 30, 2011 Share Posted August 30, 2011 (edited) I have noticed no airflow from any of the vents. Ventsare in open position , nothing from center as well . A/C compressor worksnoticed tubes started to freeze over in engine bay after a short drive wondering why no air flow into cabin . Could this be vacuum related ? I noticed the trunk T bar release in glovebox also does not work and read something about a vacuum cannister . Edited August 30, 2011 by V10 (see edit history) Link to comment Share on other sites More sharing options...
Guest Kahuna28 Posted August 30, 2011 Share Posted August 30, 2011 I doubt it's a vacuum if your getting no airflow. Check the fan. There is a fuse (fuse-box) and a blower motor relay mounted on the inside pass fender near the fan (engine bay). Link to comment Share on other sites More sharing options...
1965rivgs Posted August 30, 2011 Share Posted August 30, 2011 There is a vacuum canister near the top of the firewall on the pass side which controls the AC door and directs air flow past the evap core and out the upper vents. You can operate the pivot by hand to direct the air flow out the upper vents. Check to see if the vacuum hose has cracked at the nipple of the canister. As a matter of fact, go thru every vacuum connection and cut off the end of each hose until you cut back to the original diameter. Any vacuum leaks in the system will rob the ability of the controls to operate all the diaphrams, not just one.If the canister is bad you can block the lever which it acts on with a small wooden block, large nut, etc...until you replace the canister. At least you will have AC until then. Good luck, Tom Mooney Link to comment Share on other sites More sharing options...
Jim Cannon Posted August 31, 2011 Share Posted August 31, 2011 I have noticed no airflow from any of the vents. Ventsare in open position , nothing from center as well . A/C compressor worksnoticed tubes started to freeze over in engine bay after a short drive wondering why no air flow into cabin . Could this be vacuum related ? I noticed the trunk T bar release in glovebox also does not work and read something about a vacuum cannister .With the fan on High, see if you are not getting air out on the floor. It does not pass through the A/C system, but at least you would them know that air is in fact making it inside the car.Once you confirm air is in fact moving, Tom is correct, you can operate the little lever under the hood to manually redirect air through the A/C and out at the dash. As Tom says, block it open with a small piece of wood as a temporary solution. Link to comment Share on other sites More sharing options...
V10 Posted August 31, 2011 Author Share Posted August 31, 2011 Thanks gentlemen for the replies, Tom I will try that out . I also found out there was a crack in the cannister and previous owner tried to repair with epoxy . Is this Vaccum Cannister readily available anywhere or is there a better solution to repair it other than epoxy ? Link to comment Share on other sites More sharing options...
NTX5467 Posted September 1, 2011 Share Posted September 1, 2011 On many later model vacuum-operated a/c systems, the "default mode" for when the system loses its vacuum is for the air to only come out the defroster and floor heater air vents, even if the system is on "A/C".I wonder if the "cannister" referenced is really a "vacuum actuator" instead? Typically, the "cannister" or "reservoir" is where the main vacuum source for the hvac system attaches, and is then routed to the hvac controler on the instrument panel (or also to the ComforTron control mechanism under the instrument panel--if equipped).Snipping the ends of the vacuum hoses, at their attachment points, can be a good idea. With age, the hose will take a set to whatever it's slid over, then shrink with age, and can possibly split or become loose as a result.Just some thoughts . . .NTX5467 Link to comment Share on other sites More sharing options...
Jim Cannon Posted September 2, 2011 Share Posted September 2, 2011 We may be having a communication breakdown. Here is a picture of the vacuum actuator that puts air out on the floor (no vacuum applied), half on floor, half out dash (vacuum applied to outer nipple only) or out of the dash only (vacuum applied to both center nipple and outer nipple):The vacuum storage canister mentioned looks like a black plastic or metal can with a nipple or two on it but no metal actuator to get pulled in. Link to comment Share on other sites More sharing options...
Guest rbarnett614 Posted September 18, 2011 Share Posted September 18, 2011 Old Air Products in ft. Worth, TX has the vacuum assembly in your picture. Make sure you get the one with the two connectors on the front side. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now