Guest 34Airflow Posted May 8, 2011 Share Posted May 8, 2011 Can anyone tell me where I might find a steering wheel puller as described in the below thread as a split type.I am trying to remove the steering wheel on our 1934 Chrysler Airflow CU and the Chrysler Maintenance Manual calls for a steering wheel puller CN-232. It appears to be similar to the one described in the thread below from Hupp36. Need to remove the steering wheel to pull the steering column to replace our steering gear box that has excessive play. Thanks Ray<table id="post779815" class="tborder2" align="center" border="0" cellpadding="6" cellspacing="1" width="100%"><tbody><tr><td class="thead" style="font-weight: normal;"> July 30th, 2010 </td> <td class="thead" style="font-weight: normal;" align="right"> #2 </td> </tr> <tr valign="top"> <td width="175"> Hupp36 Senior Member Join Date: Feb 2009 Posts: 230 </td> <td class="alt3" id="td_post_779815"> Re: 31 Steering Wheel Removal <hr style="" size="1"> The nut is a right hand thread. Lefty loosen, righty tighty. After removing the nut that holds the wheel on, spray some penertrating oil around the main shaft. Yes you will need a wheel puller. Use a split type that goes around the steering wheel colum and slides up under the steering wheel. DO NOT pull on any part of the bakelight sterring wheel as it will crack or brake. Straddle the center of the wheel and turn the wheel pullers center bolt to the right aiming it at the center of the shaft that holds the steering wheel on. Increase the tension on the screw in steps. Tap the center bolt on the steering puller after each time you increase the tension. I can not tell you how much tension to apply to the center bolt as I have never measured it. I guess its a sense of feel. Good Luck</td></tr></tbody></table> Link to comment Share on other sites More sharing options...
Guest 1hooligan Posted May 8, 2011 Share Posted May 8, 2011 Air flow, Hupp was very correct on his response. The only thing that should be added it is a three day job. First day remove steering wheel nut and spray the oil with gusto on the top of the shaft, let sit. The second day turn the wheel 180 degrees, and spray again, let sit. The third day try to remove. put the nut back on at least four threads, tap.......patience, DO NOT FORCE IT. This has worked for me more than once. Regards, and good luck, Pat Link to comment Share on other sites More sharing options...
Guest Snopack Posted May 8, 2011 Share Posted May 8, 2011 I believe the tool mentioned is referred to as a "bearing splitter", see attached.http://www.harborfreight.com/media/catalog/product/cache/1/image/9df78eab33525d08d6e5fb8d27136e95/i/m/image_2833.jpgJohn Link to comment Share on other sites More sharing options...
Johan Boltendal Posted May 8, 2011 Share Posted May 8, 2011 This is a period steering wheel puller, not to buy any more, I think, but you could make one your self. Johan Link to comment Share on other sites More sharing options...
Guest 34Airflow Posted May 9, 2011 Share Posted May 9, 2011 Johan, I've made one, but the steering wheel still wasn't moving, so I thoughtI would try and see if maybe some out there had the real thing. Snopak, I eyeballed my bearing splitter when we first started to try and remove the steering wheel, but could not come up with a way to rig it up to the wheel.1hooligan, I will have to remount up the puller I made and give it another try. Have been spraying it down several times a day for a week. Thanks for all your responsesRay Link to comment Share on other sites More sharing options...
keiser31 Posted May 9, 2011 Share Posted May 9, 2011 I learned not to get my face too close to a steering wheel when trying to pop it off....sometimes they fly pretty far. Link to comment Share on other sites More sharing options...
Coley Posted May 28, 2011 Share Posted May 28, 2011 I would NOT tap on the steering shaft that is one piece. You can damage the bearings or races in the steering box.If your car has a 2 piece, then gentle tapping might help. Link to comment Share on other sites More sharing options...
idrjoe_sandiego Posted June 10, 2011 Share Posted June 10, 2011 Is this Kent-Moore puller what you are looking for? I wish I had one; doesn't look hard to make, though. Here's another one the Model A guys use. That one looks more risky! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now