MDL
Members-
Posts
27 -
Joined
-
Last visited
Content Type
Forums
Gallery
Events
Everything posted by MDL
-
Houk #4 overland 6 pin hubs need all 4 have good wheels all ready
MDL posted a topic in Parts Wanted
Wtb 1 or more hubs need to make a set have some caps but may buy ones that are better than mine too. Thanks -
Hi looking for 1925 dodge closed car window crank handles. Can you Help? Thanks mark
-
Looking for what I have been told are 1923 dodge coach window crank handles
MDL replied to MDL's topic in Parts Wanted
Hi all still looking thanks -
Looking for what I have been told are 1923 dodge coach window crank handles
MDL replied to MDL's topic in Parts Wanted
Handleman found me 2 thanks rich!!!! Still need some more please look through your stashes . Thanks aaca...... -
Hi john it's mark in canada with the brooks I am interested i will try to call tomorrow two 5 o seven two 7 11four 2
-
The are pictures in the discussion forum under anyone restoring a doble
-
Looking for empire pilot for cruban burner any condition considered. Also cruban burner parts for my 1924 brooks steamer. Thanks
-
Hi does the large one have a pinch bolt on the Side? Thanks mark
-
Hi roger I am in victoria bc I have a brooks It has been discussed here please call me two 5 zero 7 two seven elven 42 thanks mark
-
Hi have interest in the brooks parts where are you Located? Mark
-
Looking for 21 inch wire wheels and hubs to fit my brooks steamer
MDL posted a topic in Parts Wanted
Want to convert my 1924 brooks steamer to wires. Need hubs and wheels tires are 5.25/5.50 21. Wondering what's out there and available . Will post taper axel diameter tommorrow. Has rear brakes only 6 bolt drums. Thanks pictures of my car are in the discussion forum under anyone restoring a doble -
Source for 3/8 oval head (football shape) carriage bolts for wood wheels
MDL replied to MDL's topic in General Discussion
I have sent a note to the fellow in England that is on this site about getting the dimensions of the bolt head. I have communicated with him before but it takes a few days for a response . The bolts pictured above are not what I am looking for but thank you for your effort. I think they are going to be in the 1 1/4 × 1 inch range. I will post size once I am sure . May have to go make them myself route. Thanks for all the input on this. Mark -
Source for 3/8 oval head (football shape) carriage bolts for wood wheels
MDL replied to MDL's topic in General Discussion
OK my mistake. Took a wheel apart and got some correct measurements . Bolts are 7/16 dia. And 2 inches long from underside of head. Sorry for the confusion the modern bolts in rhe wheels looked to be 3/8 but are not.. thanks -
Source for 3/8 oval head (football shape) carriage bolts for wood wheels
MDL replied to MDL's topic in General Discussion
Thanks for all the response to this. I will check on the length today I think you are correct they will be shorter than 4 inch. Going by the markings on the spokes the head is wider and obviously longer than a standard carraige bolts. Certainly can be made but I thought I would ask around first I need 12. If l only needed 1 or 2 I would have tried something all ready. Thanks again -
Source for 3/8 oval head (football shape) carriage bolts for wood wheels
MDL replied to MDL's topic in General Discussion
Unfortunately I don't have any original bolts .someone before me put standard carraige bolts in place -
Pictures of my brooks Car is 11th car built going by serial number. It is a 1924 milage is thought to be 470 original miles. Mark
-
Hi I have a brooks here in victoria I could really use these parts . Can someone one PLEASE put me in contact with ths person. BEFORE This goes goes to scrap. Please contact mark 250 727 1142
-
Hi George mark here I have sent a couple of emails are you getting them. Is your email been Changed? Please contact me . Thanks mark
-
Hello I am new here. I have a brooks in canada I would like to contact you to discuss the cars .I would really like some pictures of your burner and boiler. I just had a new asme boiler built here in canada and am in the process of dealing with the burner. Thanks