John Gelfer Posted September 17, 2010 Share Posted September 17, 2010 I'm trying to find the TDC mark on my flywheel. I was expecting a small punch mark, arrow, or something like that. What I see is a bunch of numbers that don't seem to correspond to degrees. Some are odd, and some are even. So far I have seen 15, 17, 18, 27, 36, and 45. It looks like the 45 is TDC to me, but I'm far from certain. All the numbers have a vertical line between the two digits that is taller then the digits. I'm viewing these numbers through a little peep hole. Since it's an L-head engine, it is pretty hard to see when the valves are closed and the piston is at TDC. Any ideas on this numbering system? BTW, it is an 8 cylinder Lycoming 226 cu. in. engine in a 1928 Gardner. Link to comment Share on other sites More sharing options...
nickelroadster Posted September 17, 2010 Share Posted September 17, 2010 All you need to do is remove #1 spark plug and put your finger in the hole. When you are on compression stroke, you will be able to feel the pressure building and trying to push your finger out of the way. When you do this you should be able to tell when you are at the top of the stroke. This will allow you to be able to identify the mark on the flywheel that is TDC. Link to comment Share on other sites More sharing options...
Rusty_OToole Posted September 18, 2010 Share Posted September 18, 2010 All you need to do is remove #1 spark plug and put your finger in the hole. When you are on compression stroke, you will be able to feel the pressure building and trying to push your finger out of the way. When you do this you should be able to tell when you are at the top of the stroke. This will allow you to be able to identify the mark on the flywheel that is TDC.A more accurate way to do the same thing is to make a pipe to screw into the spark plug hole and make a soap bubble on top. You can tell when you reach TDC when the soap bubble stops growing. This is surprisingly accurate. Link to comment Share on other sites More sharing options...
John Gelfer Posted September 19, 2010 Author Share Posted September 19, 2010 Thanks for the help! The "bubble method" worked very well to find the exact TDC. I attached a hose to the fitting in #1 cylinder, and dipped it in some soapy water. My wife watched the bubble grow while I cranked over the engine with my McGyvered starting handle. After several tries, we were certain where TDC was. The number on the flywheel in the peep hole was 18. I don't understand the number, but that's what it is. Maybe they meant 1 of 8?. That still doesn't explain the other numbers. Link to comment Share on other sites More sharing options...
Guest trainguy Posted September 20, 2010 Share Posted September 20, 2010 The 18 means cyl 1 and cyl 8 are at the top of their stroke,which of these is on compression is determined by the position of the camshaft. Link to comment Share on other sites More sharing options...
Rusty_OToole Posted September 20, 2010 Share Posted September 20, 2010 So does that mean the flywheel is marked for the position of the following pairs of pistons, 1&8, 2&7, 3&6, 4&5? What about 15 and 17? Link to comment Share on other sites More sharing options...
Guest trainguy Posted September 20, 2010 Share Posted September 20, 2010 Good question.the marks on the flywheel are used for setting the valves.I will have to give this more thought.The numbers are often accompnied with IO[intake open]ic[intake close,EO&EC for the exaust. Link to comment Share on other sites More sharing options...
Rusty_OToole Posted September 20, 2010 Share Posted September 20, 2010 Wow cool. This would make accurate valve adjustments a cinch. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now