-
Posts
2,111 -
Joined
-
Last visited
Content Type
Forums
Gallery
Events
Posts posted by broker-len
-
-
I have a good quality rubber matting for boards or inside floor several paterns can sent pictures and samples please e mail direct at bobnroman@yahoo.com
-
I have had my 32 PA for 40 years It seemed to be a original car when I got it it has positive ground I looked in owner's manual and it states negitive ground I also have a repair manual covering 31 to 36 put out by nappa in 30s it shows positive ground for both my PA and 36 plymouth STRANGE -------- BR
-
have a 31 PA plymouth does any one know the condenser value for my car bobnroman@yahoo.com
-
real good book about 60 pages 31 to 36 plymouth alot of technical info can send pictures----------- E mail directly to bobnroman@yahoo.com
-
Can provide running Board matt for 30 and 31 Packard can send pictures and samples please E mail direct to bobnroman@yahoo.com
-
I spoke with lubriplate they have 140, almost $ 50.00 a galon and 250 no 160 Black bear has 140 straight no sulpher sells only 5 gal pails costal can provide same by the galons low price E mail me for order info-----------bobnroman@yahoo.com
-
if you send me an E mail we can talk on phone and I can help you with alot of your problems bobnroman@yahoo.com
-
i HAVE TWO 30S MOPARS THE STEERING BOX,REAR AND TRANS ALL CALL FOR 160W OIL---------WHERE CAN i GET IT ?-------------BOBNROMAN@YAHOO.COM
-
Owen--------------what part of NJ and you I am south,,, near cherry Hill remember the Dupont stuff thanks for the reply send me an e mail at bobnroman@yahoo.com will send pictures of my cars
-
on a 36 plymouth and head goes in the ash tray space on the dash if you have two wires on the unit my guess one is the ground or antena open it up and see where they go-----------bobnroman@yahoo.com
-
I have a 31 PA almost same engine do not use grease--------------it gets into the gage and destroys it to prime the pump eather take off the top line going from pump to engine or just take off the pump fill with oil and replace it with out spilling it out----I have done this on mine -----if you want to talk bobnroman@yahoo.com
-
looking for unconventional advise for cleaning my hony comb radiator with out pulling had sugestion from a PA member to use the stuff for cleaning water building up in bath tubs also using citric acid some one else mentioned kerosine -------PLEASE HELP-----doint want to take it out and it over heats when it get hot new thrmo and engine rebuild also checked the timing--------------- bobnroman@yahoo.com
-
I have a 4 cylinder plymouth the engine is rebuilt----I started using straight 30 and found that when at driving speeds the oil pressure was as recomended 30 to 40 lbs at Idle the pressues went way down I think the multi holds a more even presure I do use a zink additive in both my 30s cars bobnroman@yahoo.com
-
I have a 36 plymouth also a good manual for sale and rubber for floor if you need help E mail me at bobnroman@yahoo.com
-
I have two early mopars with the third brush I do sell a book showing how to set up the charging rate but you want to start with a fully charged , new battery and just doint generate any more amps than you need you will kill both the battery and the armiture------------------bobnroman@yahoo.com
-
can supply matting for 31 to 33 packard boards---can send pictures and samples bobnroman@yahoo.com
Side Sill Moulding
in Plymouth
Posted
these mouldings are from front hood to rear fender under doors bolt to body on plymouth, chrysler, and other mopars can send pictures made of alluminum please e mail me directly at bobnroman@yahoo.com