67conv

1924 Dodge Brothers Business Coupe Has original engine,14,000 actual miles. Frame off restored to original condition.$30,000 Call 828-635-1000 Cell 828-310-2725

I recently took the complete rear end out from under my 67 vista cruiser for a little clean up and paint. I found the code on the axle tube( its MG) and also painted on the center section.Its a BUICK rear end and I can't find the code listed in the service manual or online anywhere. I know its a 3.23 ratio without posi.Any ideas? Thanks Tony

Got the switch back in and checked the dome lights. When I open the rear door the dome lights come on but when I open the front door only the courtesy lights work. I would think when the front door is open both courtesy and dome lights would come on.I'll check my service manual tomorrow to see if it has a trouble shooting guide.If anyone has any ideas let me know. Thanks Tony

Thanks for the tip on the starter,I didn't get that far along today.Most of my time was spent on the dome lights. I had dash lights,courtesy lights,glove box lights,clock worked but no dome lights.After checking every thing we finally(I think) found the problem.One of the rear jamb switches was bad. I'll have to clean it in some rust remover and clean the paint off of the jamb.Everything on the rear of the car worked fine.

Thanks Joe for the reply,I had planned on connecting my pos cable to the horn relay and neg cable to frame. I've already connected the starter, so I'll test that circuit also.If you have any other tips let me know. I'll do the test tomorrow and let you how it goes.

Just got the dash and steering column back in the vista last weekend, all wires connected from the firewall back. Is there a way to test lights, switches etc. without the engine and other front end parts assembled to the car? I though about connecting the one harness for the engine . Would the starter need to be connected to the harness and grounded to the frame. If anyone has a better plan let me know, I just want to check my progress so I can correct any problems before I go any further. Thanks Tony

I called them over a week ago and he said their shipment was due the next day and that he would call me back. Still no call, guess he forgot. I'll call back tomorrow.

I'm looking for a dash speaker for a 67 cutlass and a rear speaker for a 71 442.Must be factory equipment and in good working condition. Thanks Tony

I decided to start the rebuilding of the front end of my 67 vista yesterday. I noticed the drag link has some free play . Is there a rebuilding service for these? My local napa store says he can only get the one for manual steering and mine has power.

I have seen '65 with body color and do recall at least one '66 with body color but did'nt check the build plant.

Does anyone have a Hollander book to check if there are any gas tanks that interchange with a 67 vista cruiser. I've been told possibly an El Camino would but like to know for sure. Thanks Tony:confused:

I drove the car on our dead end street last sunday. I had some brakes but not good enough to drive on the main roads. My son helped me bleed the brakes again and there was some air in the system. I guess you can expect this since the whole system was open for a few weeks. I'll keep working on it till I get it where it works right. Then on to the cooling system.

Joe I talked to Bob Brannan over the phone today and he gave me some tips on bleeding the brakes. I now have fluid to all four wheels with good pedal pressure and no brake light glowing. I have not yet done a road test to see if they work correctly, this will be a few days yet.Thanks for the tips on checking the combo valve off the car,hopefully i wont need to replaced this one. Tony

I've installed a used proportioning valve found thru another web site. The guy said it was good, however once installed I have no fluid going to the left front caliper. I removed the hard line and checked with compressed air. It checked out ok. Put it back on and hooked up my hand held vacuum pump to the end going to the calipers rubber line (new). No fluid coming out. Is there a way to check the combo valve before installing it, this is no quick job. Any suggestions would be great. Thanks Tony:confused:

Joe I found a spare combo valve I had sitting around for years and took the big end fitting off . The piston seems to be stuck so I soaked it in Evaporust. I tried using compressed air to force the piston out ,but no luck. I even took a brass drift and tapped the piston to try and move it but nothing happened. Am I going about this the right way or can you suggest a better approach. Thanks Tony

Joe , I did bleed the m/c when I first installed it, but I may not have got all the air out. That is what I'm going to try tonight. I did'nt know the combo valve could be rebuilt. Is there a kit for that or do you just take it apart and clean all the rust out. Thanks for the help. Tony

I'm trying to get the brakes working on my 71 442. Checked all brake parts ,found nothing leaking brake shoes good, pads on front good, bled the brakes twice still very little pedal pressure and the brake light stays on.I changed the master cylinder years ago and had the same problem. Should I try to bleed all 4 wheels again or am I missing something simple.

Now that I have the 442 running again I noticed the tach is showing about twice the rpm it should. Is there anything to check that would cause this? Also I'm thinking about installing a pertronix ignitor 3 and hotter coil. Would my tach still work with this setup? Thanks

Thanks for the tips guys, My plan is to use some heavy duty cleaner that I can heat up, move the tank around for awhile then let sit for a few hours. Then flush out with clean water and dry with compressed air and then sit in the hot sun for a few days.

Just dropped the gas tank on my 71 W30 after sitting for over 15 yrs. The inside looked very good with just a small bit of trash ( not rust). What should I use to flush out the tank. I have a pressure washer but I dont want to take a chance on some water being left inside. Thanks for your help.

While going through some of my literature I came across a new car invoice for a 1967 olds 98 LS VIN # 386697M227156. If you have this car and can prove ownership its yours for the cost of postage.This car was sold new to Arnold Berman in Altoona PA. Thanks Tony

Thanks Glenn I'll give my local paint store a visit.If they can't help the web site you posted looks like they can. Tony

I've been looking for awhile for the correct spatter paint for a 67 cutlass. The only thing i found was the spray can stuff. Don't like it goes on too thick and does'nt look like the original. Anybody know where I find the right stuff. Tony

How do you know if you're buying ethanol gas? Are the gas stations required to post a sticker on the pump? I have never had a problem till last week, while driving my 67 olds in 93 degree heat it seem to run out of gas but it had1/2 tank full. After an hour to cool down I poured a little gas in the carb and drove it home. I have'nt checked the filter yet ,or is this caused by vapor lock? Thanks Tony

Don't know if someone from OCA read this post but I got my 20 yr pin today. Thank you OCA.