1956322
-
Posts
560 -
Joined
-
Last visited
-
Days Won
1
Content Type
Forums
Gallery
Events
Posts posted by 1956322
-
-
The harmonic balancer bolt for a 322 should be torqued to 55-65 ft pounds.. the 200 ft pound spec is for 57 and later bigger engines
-
2
-
-
If you decide to go the push button route there’s an easier way which bypasses everything.. run a 10 gauge wire from the junction where the battery positive cables meet to one side of the new push button…run a ten gauge from the other side of the new push button down to the starter solenoid.. easy pezzy and bypasses everything.. just be aware that that button will be hot at all times
-
Fusick I believe had them.. although not literally new but rebuilt
-
1
-
-
I’ve always been told not to Mount an oil filled coil horizontally as the top of the windings won’t be covered in oil and eventually it’ll cook itself.. I’ve been running an epoxy filled msd one for years with no problems in this New Mexico heat.. I’m also running a full msd set up as well.
-
Hi I’m looking for the brackets that attach the manual steering gear box to the frame on a 1956 Buick Special.
-
I got back my old 66 f100 recently and the gas that was in it was about 3 years old.. it was varnish in a very bad way..i got lucky running it no stuck valves but I’d much have preferred not to risk it
-
1
-
-
Tapping with a piece of wood is a good idea but probably the best preventive at this point is fresh gas!!!
-
1
-
-
They offer two different kinds one is just regular conventional dino oil and one is a full synthetic.. i run the conventional one.. no problems at all even on our hottest days or coldest days
-
For what it’s worth i use valvoline vr1 10-30 year round in my 56 buick..i live in Albuquerque NM and use it daily the engine was rebuilt about 20 years ago
-
1
-
-
I’ve heard you can swap to a 58 set up...
-
I set mine at 14 based on experience with other engines at this altitude and the Centerville boys recommendation of 10-12...
-
That’s what I’ve read:)
-
Ok i got it much better turns out my vacuum gauge has seen better days..575 in gear 725 in park timing is 14...edelbrock 1906 carb and msd distributor new intake gaskets..vacuum in park is 16 in gear 12 keep in mind in at 5500 ft altitude
-
Actually this is after a good tune i can get it lower but it’s not as smooth... the mounts are all pretty fresh
-
My 56 seems to run best at about 725 in gear which is about 975 in park is this a concern for the dynaflow particularly engaging reverse??
-
Be especially careful with the front cab mounts they love to rust away completely and are easy to over look
-
2
-
-
Now running a 180 Oreillys part number 3478.. ran a 160 for years but it runs better with the 180
-
1
-
1
-
-
I’ve had the worst luck with modern replacement voltage regulators and they were all made in the usa just junk some dead out of box and yes i polarized them..finally got fed up and went with the powermaster power gen
-
My 56 has a shroud
-
1
-
-
Don’t worry old tank i was just teasing you a tad i understand why the original set up has issues with hotter sparks:)
-
I’m super hard headed I’m running a msd distributor and box..gasps heard around the room lol
-
1
-
-
I’m a fan of the pertronix systems but that being said i did have one go out on me that wasn’t a go no go situation.. this went on for weeks in my 66 f100 middle of summer hot hot here in Albuquerque and I’d always get stuck in bad stop and go on this one spot.. after a few minutes of this the truck would run bad but once i got going it would clear and be perfectly fine until the next time i got stuck there..i tried everything fuel related as i was convinced it was vapor locking on me.. after about a month of this one day I’m stuck there again and it starts acting up again but this times actually dies.. yup no spark bad ignitor.. replaced it with a mallory unilite points eliminator and never a problem again.
-
1
-
-
I have that same timing light.. It’s also sold as blue point snap on.. love it and it even works with my msd boxes correctly
-
Good luck!! Wish you were closer although I’m hoping to move back to nc sometime in the future:)
53 started but starter re-engaged when gas pressed
in Buick - Post War
Posted
But to answer your question the starter button will be hot at all times however you’ll still need to use the ignition to start it.. it will have no affect on the charging system.