jbbuick22
-
Posts
647 -
Joined
-
Last visited
Content Type
Forums
Gallery
Events
Posts posted by jbbuick22
-
-
If you go, check out Union Pacific 4014 Big Boy it's at the north end of the lot , on its way to WY for full restoration
and will joint UP's other steam engines in their heritage fleet.
JB
-
Shawn,
Try J and M Machine in Southboro MA. Check their web page http://www.jandm-machine.com/.
They are excellent, and will tell you if they can help or recommend an other shop.
JB
-
Try South Shore Bearing in Quincy MA.
JB
22-6-55 Sport Touring
-
Dwight,
If you order pistons from EGGE make sure they have the correct compression height, (wrist pin center to crown, top of the piston).
JB
22-65-55 Sport Touring
-
Dwight,
You need to use a puller because the axle shaft has a nut on the other end inside the diff housing.
Lief's pics show it both the assy pic. and the parts pic. of the axle shaft.
The 4 cyl hubcap is under 3" ( 2 3/4 maybe).
JB
22-6-55 Sport Touring
-
Terry,
The hub cap dimension is for a 4 cyl car and they use 23" wheels.
Still have water pump seals???
JB
22-6-55 Sport Touring
-
Try J and M Machine in Southboro MA.
They have an excellent reputation. Web site http://www.jandm-machine.com/
JB
1922 Buick model 55 Sport Touring
-
John,
The "Edison" looks like a scale model compared to the 4014 Big Boy that Union Pacific is now restoring.
Check out " upsteam.com"
JB
1922 Buick 22-6-55 Sport Touring
-
Michael,
Try McMaster Carr, they have a very similar fitting. (High pressure quick assembly brass compression tube fittings).
JB
22-6-55 Sport Touring
-
Michael,
You could use a spdt (5 pin) relay, the switch would operate the relay.
JB
22-6-55 Sport Touring
-
Corkcab,
There are some differences with the dimensions Lief posted, but looks the same.
The bottom is 3 3/4", between the pivots 11", upper frame 27 3/4x 10 3/4", height 26 3/4".
The mounting holes in the body are 32 1/2"
JB
22-6-55 Sport Touring
-
Corkcab,
I found a complete windshield, it is missing the most of the lower frame, and the top of the posts are different than
the pics Lief posted, where the top fastens. The posts were plated at one time Model39??
send a PM and I can send you a pic.
JB
22-6-55 Sport Touring
-
Corkcab,
I may have a complete windshield for this car. Will check this weekend.
JB
22-5-55 Sport Touring
-
Dick,
The headlights you need are the same as 23 sport touring/roadster. Try Don Axelrod in Lynn MA 781-598-0523
JB
!922-6-55 Sport Touring
-
Dick,
The 1920 fenders are different, you need 1921 or 1922.
JB
22-6-55 Sport Touring
-
F&J
I have an interest in the Buick chassis. Send a PM
JB
-
Dwight,
The larger rim sizes are easier than the 19" ones you are changing. A rim spreader will work , but be careful
not to bend the rim. Rim spreaders are biggest cause for bent rims.
JB
-
Jim,
Check for spark, if none clean the points, when they sit open for a long time they can get coated with corrosion.
emery cloth, then a dollar bill, the paper in the bill does a great job.
JB
22-6-55 Sport Touring
-
George,
Be sure to have any replacement block magnafluxed, it may be no better than your orig.
JB
22-6-55 Sport touring
-
George,
Here is J and M's web site J&M Machine Company: Engine Rebuilders.
They can repair it as new. Call them you may be surprised. As far as a new one $$$$$$$$$$$$$$$$$$$$
JB
-
George,
Cast iron can be repaired. J and M Machine in Southboro MA is an excellent engine restoration shop and can expertly repair you block. A replacement block will be very hard to find.
JB
22-6-55 Sport Touring
-
Fred,
The rear fenders for the 1921 1922,6 cyl cars are all look the same, the difference for most is the width at the top and possibly the mounting to the running board. You could use a narrower one and extend it to fit.
John
-
Fred,
You need to include the dimension across the top, from bolt hole to beaded edge.
Rear fenders all look the same, 2 or three measurements is the only way to ID except part #'s.
JB
-
Tom,
Have you found anything yet?? If you take the brg caps off keep track of the shims.
JB
Buick wheel rims
in Buick - Pre War
Posted
Tim,
I think the rims should be black, the rim catalog shows cad plated up to about 1926 ????? then black after.
I'll check the book later.
JB