gofasttoday Posted November 7, 2016 Share Posted November 7, 2016 I can't find the adv timing mark . I can find the syn mark. Is it possible to use a timing light to time the car? I have it apart now but will be wanting o time it to see if that is causing the over heating.. Link to comment Share on other sites More sharing options...
raydurr Posted November 7, 2016 Share Posted November 7, 2016 The timing indicator on my 29 is on the front of the flywheel housing ,behind a swing away cover. The most common causes of overheating on the Buick in lines are blocked radiator passages and blocked coolant passages in the block water jackets. In this forum you will find many discussions regarding this topic. Since you appear to have the manifolds removed, I would also remove the long coolant cover to inspect and remove any possible gunk. There is usually quite a bit . Good luck! Link to comment Share on other sites More sharing options...
gofasttoday Posted November 7, 2016 Author Share Posted November 7, 2016 Thanks already removed the side cover and reversed flush the rad. that's why the manifolds are off . waiting on gaskets, I can find the second timing mark on the flywheel for the second set of points but not for the one for top dead center for #1 Link to comment Share on other sites More sharing options...
gofasttoday Posted November 7, 2016 Author Share Posted November 7, 2016 Any one know if you can use a timing light to time these cars? Link to comment Share on other sites More sharing options...
Larry Schramm Posted November 8, 2016 Share Posted November 8, 2016 5 hours ago, ford40 said: Any one know if you can use a timing light to time these cars? You can use a timing light on any car. I use one for my '1915 truck. Only issue is finding the mark for #1 at Top Dead Center and I need a separate 12 volt battery to power the timing light because the truck is 6 volt. Link to comment Share on other sites More sharing options...
gofasttoday Posted November 8, 2016 Author Share Posted November 8, 2016 Great I will try that as soon as I get The intake and exhaust gaskets. should be able to locate the TDC mark with it. Link to comment Share on other sites More sharing options...
Larry Schramm Posted November 8, 2016 Share Posted November 8, 2016 You need to find the timing mark while the engine is not running and clean/mark it so you can see it while the car is running. Link to comment Share on other sites More sharing options...
gofasttoday Posted November 8, 2016 Author Share Posted November 8, 2016 I've looked and can't find it. I can find the syn mark for the second set of points but not the one for number one cyl. It must be very faint. Link to comment Share on other sites More sharing options...
gofasttoday Posted November 8, 2016 Author Share Posted November 8, 2016 If I find the syn mark how far back do I have to turn the flywheel to be at the number 1 tdc Link to comment Share on other sites More sharing options...
Bob Engle Posted November 8, 2016 Share Posted November 8, 2016 A different way to find your timing: Set #1 cylinder intake valve lash at .008". put a dial indicator on #1 rocker arm and turn over engine by hand until #1 valve opens .004" (.012" total rocker movement). At this point #1 cylinder is 4 1/2 degrees before top dead center. Mark the crank pulley at this point. Measure the diameter of the crank pulley and calculate the circumference and divide by 180 degrees and you will have the spacing for each degree. If you have a modern timing light, you can set the advance on the light at 6 1/2 degrees and then set your idle timing on the mark for 4 1/2 degrees. Be sure you have the spark advance set full ahead when using this method. Bob Engle Link to comment Share on other sites More sharing options...
Larry Schramm Posted November 9, 2016 Share Posted November 9, 2016 (edited) The way that I found the top dead center for the number one cylinder is to remove the sparkplug and put a long straw in the spark plug hole and turn the engine over by hand until the straw is the farthest out. Just do not drop the straw in the cylinder. That puts the cylinder at the top +-. Then look for a mark on the flywheel. You are now in the neighborhood for timing the engine. Edited November 9, 2016 by Larry Schramm (see edit history) Link to comment Share on other sites More sharing options...
gofasttoday Posted November 9, 2016 Author Share Posted November 9, 2016 I think I will try the straw trick first . If that doesn't work i will try bobs way. Thanks Dave Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now