bones1931

Was able to purchase a complete kit from the Carburetor Shop. Thanks.

Looking to buy a needle valve and seat for a 1934 Buick 60 Series Club Sedan. Has a Marvel carburetor. 8 cylinder. Mike McDonald mwmcdonald@accesswave.ca

Thanks Mark will check out these sources. Mike

Looking to find a source for parts for the vacuum brakes on our 1934 Buick 60 Series Club Sedan. Any information or help with this would be greatly appreciated.

Looking to purchase rear manifold section for 1934 Buick 60 series. Thanks Mike mwmcdonald@accesswave.ca

You might try Al Lambert Gasket City. alambert@gasketcity.com Great to deal with.

Thanks for the information have sent and e-mail off to see what they can supply. Our rear wheel cylinder is leaking from the bleeder and doesn't tighten up. Not sure what you get in the kit. Thanks Mike

Need help in finding a rear right side brake cylinder for our 1947 International half ton pickup. Thanks Mike

Have a set of 1931 Essex Wire Wheels 19 inch 5 bolt pattern need to find the hubs. Have one front now need another front and two rears. After much searching was able to locate the wire wheels for the 30 Essex Roadster. Any help with this would be appreciated. Thanks Mike mwmcdonald@accesswave.ca

Forgot Picture,

Still looking for Essex Wire Wheel 5 bolt hubs for 1931 Essex 19" wire wheels. Need 1 front and two rears. Have the wire wheels and hubcaps need the hubs. Have located the 6 bolt hubs for the 1930 Essex. See attached photo. Will be in Hershey.

Have two sets of hubcaps for 30 or 31 Essex wire wheels. Can someone tell me which ones are which? The wire wheel opening is about six inches across. Thanks Mike mwmcdonald@accesswave.ca

Dave here is a picture of the 1930 Essex Roadster with the wooden spoke wheels. Mike

David have sent you a private message. You can contact me at mwmcdonald@accesswave.ca Thanks Mike

The standard wheels were wood spoke and the optional were wire. E-mail mwmcdonald@accesswave.ca Thanks Mike

Still looking for 5 bolt Essex hubs front and rear. Any help with this would be appreciated. I have included a picture of the wire wheel hubcaps that fit these wire wheels the top set I think are 1930 Essex and the bottom are I think 1931 Essex. The two sets of hubcaps are both slightly less than six inches across. Thanks Mike mwmcdonald@accesswave.ca

Will, not sure how the forum works but sent you a private message through the forum. Let me know what you want for the Essex hubs. I don't mind waiting. Thanks Mike mwmcdonald@accesswave.ca

I would be very interested in the 5 bolt Essex Hubs that you have. It doesn't matter to me as long as they will fit the wire wheels that I have and will work on the 30. I need one more front and two rears but would be interested in what ever you have. You can e-mail me at mwmcdonald@accesswave.ca Thanks Mike

Looking for one front hub and two rears for 1930 Essex 19" 5 bolt pattern wire wheels. I think the 1931 Essex wire wheels are the same but have a different hub cap. Have attached a picture of the front hub and wheels. Looking for any infornation on the rear hubs. Thanks Mike

Have traced the rough draft pattern from the 30 Essex Roadster side curtains. If you e-mail me your address, I will mail them to you. Thanks Mike

The 30 Essex Roadster has rods that go into the two holes on the door and go through pockets in the side curtains. The rods I had made by shaping first with a coat hanger and then taking them to a shop to be made of rod iron. My car had the curtains but the rods were missing so I had to guess what they would look like. I put a regular household curtain rod in the top pocket of the side curtain seems to look fine but I don't know how waterproof. I will try to get you the measurements tonight. Mike

I don't know if these will help but here are a couple of pictures of my 1930 Essex Roadster Side Curtains. If you think the 28 and 30 are the same I will measure them for you. Mike

Thanks will also give it a try. Mike

Looking for hubs and hub caps for my 1930 Essex Roadster. The wire wheels are 19". I have the wire wheels, one front hub and two hub caps. Would like to post pictures but attach files in manage attachments keep coming back as failed. What am I doing wrong? Thanks Mike