rwoods
-
Posts
83 -
Joined
-
Last visited
Content Type
Forums
Gallery
Events
Posts posted by rwoods
-
-
Why not use a 6 volt alternator ? The model A ford guys use them a lot.
-
no 28 29 radiator shells were stainless steel,they were painted black or nickel plated very late 29s may have been chrome.
-
you will not pick up your 63 impala with any bumper jack as the hook has to fit the bottom of the bumper.jack the jack on ebay
-
where are the stainless stone guards for the rear quarters?
-
1957 265 cu engines came from the factory painted yellow.they were not very common.
-
check the price per quart at snyders model a parts, you have a mint.
-
That 1930 ford in the background looks like it has Pa antique plates.
-
The number for rustoleum satin black is 7777
-
This was used on ford tractors around the 1940s to 1950s, give or take a few years
F
-
1951 or 1952
-
the cap is 29-29 ford, the bird is not ford.
-
the full frame is 1957 Chevrolet they were gold for belair and silver for the two ten and one fifty
-
I have never heard of a chevelle with a 21" trumpet horn. Did you find the number in a GM parts book? If so can you post the page? Thanks Dave
try 1965 impala as they had trumpet third horn,mounted on top of inner fender
-
YES I WAS WORKING AT A CHEVROLET STORE IN 1956 AND I PUT ON MY NEW 1956 CHEVY. IT USED A SPECIAL CENTER SECTION TO HOLD THE WHEEL.THEY HAD A CHEVROLET PART NUMBER AND EVERY DEALER HAD TO TAKE ONE,THATS HOW I GOT MINE THEY GAVE IT TO ME TO GET RID OF IT.
-
1932 chevrolets also used Potter trunks straight back would be for a coupe or roadster.
-
1
-
-
automatic trans cranks were not drilled for standard trannys.the crank hole is not deep enough,stick a screwdriver in the hole and compare with your tranny.once in a while thay will fit,i have had some that were deep enough but the pilot bushing would fall out.seems that auto cranks were standard shift rejects
-
I have a 65 Monza coupe dark blue -white interior 110 with pg ,fun car to drive. had a 63 sedan in the late 60s the kids called it stinky,The defrosters kept the windshield well oiled,that was the only part that didnt rust.
-
That big light is called a passing light,that was a GM accessory fron 1939 to 1941 I would bet that amp meter really bends with all those lights on.Its a suprise to see the interior,but I like it.
-
If you look at the front of this car all those lights and bumper guards are all factory accesories for 1939.Anyone know what they called that big light on the drivers side?
That car is a lowrider,more than likely from California.It is a very nice car.
-
try a welders supply company,most of them carry 00 cable by the foot and can put the starter end on.its the same as on welding cable.
-
there is too much side trim for a delray looks like a belair,not in that bad shape for a 58 shame it could not be restored.belair two doors are in big demand.
-
i see a lot of talk about painting the inside of tailights for more light,silver or white were mentioned,is one brighter than the other?
-
motorcycle fork oil is also very good and comes in different weights such as 10 weight up to about 50 weight.
-
the tank was not full of paint.it was full of water with a layer paint on top,the parts were suspended overhead on a moving cable that diped the part down through the paint and into the water and while it was moving came back up through the paint and went into a oven to dry.
i have seen new model a ford fenders and the finish was perfect.
dupont centari that has been buffed is about as close to the dipped fenders as you can get.
1953 Chevrolet Belair Dealer showroom plates, or later?
in General Discussion
Posted · Edited by rwoods (see edit history)
the two ten convertible plate shows its either 53 or 54 as that's the only years they were made.