gongzhen2015

ok. Finds out the purpose of the I terminal is to bypass the resistor wire. So my mistery 12V wire from ignitoin coil connector is nonsense. But it do have a plug look pretty like it should connect to the choke. And the length of the wire serve that question. However, why something should supply constant 12V to a choke doesn't matter before or after engine start..... Didn't those electric choke use only about 6 to 7 volts?

Alright, found something interesting. The spare wire I talked about comming from same connector which connect to the coil which output constant 12V, Is it something should connect to the I terminal on the starter solenoid? When I got the car years ago, the starter relay dont have a "I" terminal. But, what is that I terminal do?

Good to know. So the heat is first priority thing to kill these module? Or vibration or what. Was thinking add a computer 12V fan on the control module to reduce the heat. Nice, i think these motor ran really strong. My T-bird have a llit over 100k mils which the compression result surprise me.

The carburetor was a rebuild carb. For this year since i change the module, the rough idle problem seems to be fixed. For the NOS starter solenoid, did some search found nothing on ebay.. I just keep carry a spare part in trunk.

oh yes, and for the compression. Did one weeks ago, only 1 cylinder shows slightly low at 127psi, all other at 135psi. Not so sure what psi they should be?

Its a 1979 Ford thunerbird with 302. So i basically have the same starter solenoid, i only use the S terminal. Not so sure what is that I terminal for. I could only find the 1977 thunderbird manual and it said nothing about that unattached wire, coming from the same connecter where ignition coil connectes to. yes, i sorta think the same thing. Vapor lock means no fuel in fuel bowl, so I shouldn't be able to get any fuel shot from the bowl. Could be a overheating ignition coil or ignition contro module. Was trying to find some motorcraft parts but seems they do not exist anymore, just get a Tru-tech ignition module, Standard blue streak ignition module, and going to pick a Duralast ignition module up tomorrow. The ignition coil i currently have the Standard Blue streak one. Good quality? And what i have before i think should be misfire. Car running really rough when at red light and pretend to stall. So i order a distributor cap and rotor kit to install tomorrow. Will get a video about how the car running for a better diagnoises. All the shop nearby me know nothing about those old car, which they tune my carburetor by following the manual...

Hey guys. Wonder will a vapor locked car able to squirt some fuel in the carburetor when slam on the acc pedal? I just remembered last year when i think it is "vapor lock", it can still shot some fuel to the carburetor.. by the acc pump i think. A little more thing, what should the water temp be for those ford 302 motor? Plus, i found a un attaced wire coming from the same plug connect to the ignintion coil, that it is a red wire which output constant 12V when after i turn my key.. Sort of like a , ummm Switch power wire. What is it for? Choke?

i know that. however i route the fuel line all the way away from the engine, and double shielded with nylon and chrome silver heat disspate wrap.. Test run it in park for 3 hr and so far so good. Just got a question. So the back of my ICM , only the case is aluminum or metal, the place where those wire came from was covered by some black glue? So i need to only apply grease on the metal body, to help it transport those heat to the fender?

Any one have any idea how to apply Dielectric grease/ Heatsink compund on those ignition module?

ok so i did some research. Sounds like this thing like to die when hot.... so, what to do ro make them cool?

Honestly, i was not pretty pretty sure it is vapor lock. But it did normally run really rough when idle at redlight.. I have to give some gas to stable the rpm otherwise it really looks its gonna stall. There is a EGR valve there, which i think it should be space enough?? Not so sure. And for the ignition coil. I just replaced one. Just in case if it is this coil. Plus, ignition coil can get really hot and eventually give up and work again when temps lower?? This is the controll module. yes, i just replace one of this in the car. I checked the original one installed in the car, it was all rusted and manufactured in 1978. Guess that one maybe toooooo old?? But will this thing give up when so hot? Back in last year, i didn't check for if there is spark, cuz i was so struggled on the side of the road and know nothing about it.. However, when I was working on it this year, i got it replaced with new plug and everything. The original one looks pretty rusted . Plus, i also replaced all brake line, alternator, alternator wire, voltage regulartor... And starter solenoid. I have to say, this starter solenoid was the first thing failed on my car which make me think the starter need to replaced. And for 1 year, i already replaced 3 of them.....

Hi, Summer again and want to get some attention on my car's vapor lock problem. So last year summer, after I was on the highway for a hour, the first minute i drive off th highway the engine run really rough and dies. Andthen, for the first hr i crank my battery all the way from full to none, it still wont start. (Back at that time i have no idea what is vapor lock) I guess this must be Vapor lock. After about 2 hr, i am able to restart it. So for this year, I already done the following thing to prevent the vapor lock from happening: 1. Add a carter fuel pump, fuel pressure in engine compartment reads 5.5psi. Mechanical fuel pump i just left it there, i didn't run the fuel pass the mechanical fuel pump. 2. Cut and throw the original carb bowl vent/col something canister away, i let the fuel bowl vent to the air. 3. I add a 3 port style fuel filter, and connect the third port to the original vapor line. 4. Instead of the original steel fuel line running between A/c compressor and engine (Really Really hot), I run a new rubber fuel line avoid getting close to any heat source. 5. Shielded all the fuel line/filter 6. Add a electric radiator fan. 7. The shroud was missing, so i get another one( Last year the water temp was very high. Got a new radiator this year). Are there any other thing I can do to prevent it? Just test run it in hot idle for 2 hrs, no vapor lock. Drive for 1 hr no vapor lock. but today the weather is not that hot. Besides that, my A/C solenoid kicker is kinda gumm up, which it can only hold the position but it cannot push the position, where to find them? What's their name? And, is 5.5psi good for the stock 302 and MC 2150?

car is 79 thunderbird. using all stock things including emission controls. EGR valve is new, no vacuum leak. Last time when driving off the high way, it bogged and then died all the side of the road for 2 hrs then able to start Was thinking if it is vapor lock, cause the fuel line was still original steel fuel line running between distributor, mechanical fuel pump. Just installed a fuel pump yesterday right under the fuel tank, and use the original fuel line to reach the engine compartment, then uses a shielded rubber fuel line to route away from all the heat source then with a 3 port style fuel filter then enter the cab. My question is, the 79 thunderbird have a original Vapor line build in which connectes to cronal canister which i already throw them away. and the vapor line is connects to the third port on the filter (i know the size of that line is small, but can it be use as a vapor return line/ or maybe fuel return line?) And the port above the fuel bowl which used to connect to the canister, i just leave it open or use a fuel line to route it away from engine? Plus, the fuel pump is hard reach which i need to take out the power steeing pump, is it ok just to left it there and just capped both side?(it is a 2 port pump) with the port open it makes a funny noise.. And a bit more other stuff, the car is pretty much not cooling well with the original radiator.(stock fan and shroud), is it better to replace the radiator to some aluminum one? Really want to have a digital water temp gauge, but for the current one, it reads to the Letter A within the NORMAL( still in the normal range tho) when idling at 800 rpm. Any electric fan needed? With the small inline fuel pump for only 5-7 psi, is ok to use rubber fuel line with the original steel fuel line( the long one under the car), or still have to replace to some silver braided fuel lines? Benefit if i want to go EFI in the future? Thanks