[37 CpExp Engine and Over Drive Transmission]

I have 2 complete engines with transmissions for 37 Coupe Express. I'm selling both - $1,000 for the pair.

Engine 1 has Over Drive transmission. Includes clutch, bell housing, generator, starter, fuel pump, water pump, distributor, manifolds. Everything is there except it has no carb.

Engine 2 has standard transmission NO OD.  Includes clutch, bell housing, starter, fuel pump, water pump, distributor, manifolds, and carb. Everything is there but it has no generator and no shifter lever.

 

Located in San Leandro, CA

[Marmon Sixteen parts]

Greetings: I am trying to locate 2 items for a 1931 Sixteen Victoria:

1 Lens for interior vanity light

1 Rear bumper bracket (left and right are the same)

2 Exhaust tip Cast Aluminum

 

Thanks

Jim

[Electric Choke 1938 60 Special]

Anyone have experience with the electric choke on the Stromberg AA25? Choke is stuck open. 

[Temperature gage conversion]

Plan to run the truck on 12V neg ground. The ford gauge idea might actually work. The trick on the conversion to negative ground is the gas gauge reads backwards. If I use Ford innards, seems all I would have to do is adapt the appropriate Ford sending unit.

 

Thanks!

[Temperature gage conversion]

Not going to show, but before rebuilding the capillary, I want to investigate the possibility of an electric gage behind / using the original gage face. Not sure if anyone has done this, but I thought I'd ask.

 

Thanks

[Temperature gage conversion]

Has anyone converted a thermocouple temp gage to electric?

 

Restoring a 1937 Studebaker Coupe Express. Water temp gage has a long capillary in bad shape. Would like to convert to electric, but keep the original gage face in the dash? Can this type of conversion be done?

 

[37 Dictator Speedometer]

I received an email from Andy Beckman confirming he is searching the archives. I hope to hear back soon. 

 

With regard to decals: Both the speedometer in my running 37CE and the speedometer from my current 37CE restoration show 0 to 100. Perhaps it makes sense to make water-slide decals in both 0 to 80 and 0 to 100?

[37 Dictator Speedometer]

Thank you all for the helpful feedback.

 

Currently I have three 37 speedometers. All in various stages of deterioration and none good enough to use as is. It certainly seems the 3D printer could be a viable option. Gary has been very helpful with his attempt at 3D Cad. I'm heading to the shop now to take some better photos with a ruler and a true digital SLR camera. Here are some photos using my not so smart phone.

 

Jim

 

[37 Dictator Speedometer]

Greetings: Is there anyone out there restoring the white plastic speedometer face for the 1937 Dictator / Coupe Express?

[1937 Cpe Exp front end questions]

I have three 1937 Cpe Exp J5 trucks. Two are stock and in great shape, but the third was severely mistreated by previous owners and can only be considered a parts truck. I am thinking I want to use it as the foundation for a resto rod project. I want to keep the body and interior original, but update the front end and brakes. This thought prompts a few questions:

 

Has anyone installed a Mustang II type front end on a 37 Cpe Exp frame? If yes, any lessons learned?

Disc brakes imply clearance problems with original artillery wheels. Reproductions are available. Does anyone have experience with these?

If I go with reproduction artillery wheels, I’m hoping I can adapt them to accept the hub caps Richard produced for the 37 Dictators?

 

Any thoughts or recommendations are greatly appreciated.

 

Jim

 

This is NOT the parts truck!

[Install a Planar Front End on a Coupe Express]

Thanks All. This is very helpful. My chassis is bare - no fenders, so I will have to re-use / modify the CE fenders. But, I think that will be less work than trying to swap front ends. The suspension is in useable condition and since I won't be hauling any heavy loads, should be adequate.

Thanks again

Jim

[Install a Planar Front End on a Coupe Express]

Greetings

I'm restoring a 1937 Coupe Express. I have a spare 1937 Dictator chassis with a planar front end. Can I install that planar front end on the Coupe Express frame? If not can I install the Coupe Express body on the Dictator chassis? Thought I'd ask before I start taking a bunch of measurements.

Thanks

Jim