mach1

Thanks everyone for your assistance. The heater door control cable was kinked just behind the control wheel that is why I could not get full travel.Kink straightened and now OK. As for the low voltage at compressor I found the clutch control switch in the control panel has a high resistance.Tried spraying it with WD40 and made no difference. I have now by passed the switch and put a separate switch under the dash.All works great now. Regards Felix

I have got the heater door working on a/con box by spraying some lubricant down the cable. Vents on dash now working correctly. Only problem now is I am only getting 3.7 volts at the compressor when a/c or recirc selected. Compressor works fine if I power it directly off the battery. I am thinking the guy did not put enough refrigerant which is causing compressor not to start up. I will check the wiring out on the weekend.

The cable on the engine bay box is for the heater door and I can see it disappear up behind the control panel. I cannot get up behind it even after pulling the ducting out.I will give it another go tomorrow. Also noticed the compressor clutch is now not engaging.With the compressor plug off I have 12 volts but when I connect it 0 volts. I can get compressor running by jumping it out with the battery. From the diagram it appears it could be the clutch swich in the dash or the relay.

I found a split vacuum line at the canister in engine bay,repaired and now dash vents and floor vent are working correctly. I still cannot figure out how the actuator with the mecanically operated cable on air con box is supposed to work, if I disconnect the cable from the mechanism on the box and move it physically I get hot air in cabin so it is obviously directing hot or cold air via a door in the box.

I have the 2 shop manuals and I have checked all the vacuum hoses in the engine bay and they are OK. From the book it appears to be a problem with the heater/aircon mode diaphragm but I cannot seem to locate it. I did find a diaphragm behind the passenger kickboard is this it? Also I have a mechanical cable running to the top of aircon box which does not move when any selection is made on the dash, does any one know what this is for as book does not show it. Any advise would be appreciated. Thanks Felix

Here are Pics of my 68 riviera here in Sydney Australia

Hi all, I have just regased my aircon on my 68 Riviera after importing to Australia 12 months ago and I noticed the cold air only comes out at floor level. The vent outlets on the dash are not working at all, even with vent selected. Can anyone suggest were to begin so I can get the dash outlets to work. Thanks Felix

It must have been degased when it came over to Australia.I will get it regased and see what happens. I am sure it has ACC

Hi All, One last thing i need to fix on my 68 riviera is the air con The compressor clutch is not engaging when I turn air con on. I am getting 12 volts at the connector with it disconnected from compressor,as soon as i connect it I lose the voltage. The compressor coil is OK and if I put 12 volts straight from the battery to compressor the clutch engages. The manual seams to point to the compressor clutch switch?.I cannot locate it. I do not know if there is any gas in the system,could this stop compressor running. Has anyone got any more troubleshooting ideas. Thanks and Happy New Year

Thanks for info. The first number on casting was hard to read but it was a 5

I wrote air con on it,but I was not sure that is correct

car is l/h drive and it has the vacuum pods

I want to replace the master cylinder but not sure of part number. It has delco stamped on it and I found this number stamped on the casting 6452310. The car has drum brakes all round. Can anyone supply the correct p/n. Thanks Felix

1968 riviera

Can anyone identify what this relay is for next to the ID plate in engine bay. I thought it was for the air con but not sure. Thanks Felix

Thanks for the info Randy

Thanks for the info

Does anyone know if these mirrors were an option, if so are they still available or does anyone have a good second hand one for sale. Thanks Felix

Hi, Would anyone have the 3 part numbers for the vee belts.ie Air/con,alternator and water pump belts. I can get dayco belts down here in Aus but a Gates number will do and I can xreference it. Thanks Felix

Hi, My 68 washers do not work.There is 12 vots at the coil at all times. Is the earth switched through the washer switch on dash? Thanks Felix

Hi, My 68 headlights will not retract.They worked OK when I had my rego inspection then yesterday I found them both extended. Tried cycling the light switch and checked the vacuum hoses behind grill. Any ideas. Thanks Felix

Answers to your questions Steering - 3 1/2 turns lock to lock Passenger seat - reclines seat belts - front and back seats belts are all lapbelts wheels - thety are made in Taiwan with no name. They are 17 by 8 1/2 inches.Tyres are 255/45zr17

After cleaning the plug to the antenna the motor now works but the base of the antenna comes out of the guard. I have jammed it back in and left the antenna unpluged with antenna in up position. Radio works fine.I will source the correct antenna later.

Hi Ed, I am pretty sure they are original. I have had all the seats out and all the original foam is still there.

Here are some photos of the interior.