34LaSalleClubSedan Posted May 12, 2023 Share Posted May 12, 2023 (edited) I have an electric Bermuda bell from the 1920's What makes the bell ring is a small 6 volt electric motor Very small and very fine wire. Armature is only about 1"-2" The motor is smaller than the electric motor inside a Ahooga horn like the one used in Model A Ford horns, etc. Any advise where I could send it out to have it rewound. Thanks, Jim Edited May 12, 2023 by 34LaSalleClubSedan (see edit history) Link to comment Share on other sites More sharing options...
nickelroadster Posted May 12, 2023 Share Posted May 12, 2023 Consider doing it yourself. You just need to figure out the gauge of wire used and count the turns as you remove the old wire. Many years ago in the sixties I used to rewind small electric motors like you have to hop up small 12v. motors used in slot racing cars. Just replace the old wire. 3 Link to comment Share on other sites More sharing options...
Studemax Posted May 12, 2023 Share Posted May 12, 2023 Check your area for an electric motor rebuilder. It's a common need in most urban areas for businesses. 1 Link to comment Share on other sites More sharing options...
brasscarguy Posted May 12, 2023 Share Posted May 12, 2023 Eurton electric in so cal. All they do is small low voltage winding. just sayin' brasscarguy 1 Link to comment Share on other sites More sharing options...
46 woodie Posted May 12, 2023 Share Posted May 12, 2023 I don't know if any are still around, but the guy's at Slot Car tracks would re-wind their tiny motors for more speed. Might find someone if you Google it. 1 Link to comment Share on other sites More sharing options...
jameswulf Posted May 12, 2023 Share Posted May 12, 2023 I just had a customer's rebuilt generator here in my shop (just for factory part # stamping) that was restored by this company: https://www.precision-pwr.com/ It was one of the best looking rebuilds I've ever seen. From the information on their website it looks like they do DC motors as well. Might be worth an ask. 1 Link to comment Share on other sites More sharing options...
TerryB Posted May 12, 2023 Share Posted May 12, 2023 16 hours ago, nickelroadster said: Consider doing it yourself. You just need to figure out the gauge of wire used and count the turns as you remove the old wire. Many years ago in the sixties I used to rewind small electric motors like you have to hop up small 12v. motors used in slot racing cars. Just replace the old wire. There are some YouTube videos available too on how to do this. 1 Link to comment Share on other sites More sharing options...
46 woodie Posted May 13, 2023 Share Posted May 13, 2023 If you do wind it yourself, it's more important for the armature wires to be the same length, than the number of windings. Sometimes the way the wire is wrapped the end will be too long or too short and it's tempting to snip it. Keep them the same length and re-stack the wire. 1 Link to comment Share on other sites More sharing options...
34LaSalleClubSedan Posted May 14, 2023 Author Share Posted May 14, 2023 On 5/11/2023 at 9:11 PM, brasscarguy said: Eurton electric in so cal. All they do is small low voltage winding. just sayin' brasscarguy Thanks brasscarguy, I did talk to Eurton and I think they can do the repair. Very nice people. Thanks, Jim Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now