RivNut Posted November 10, 2021 Share Posted November 10, 2021 I read in the archives that some of you have removed the flapper, shaft, and weight from the heat riser so that it just acts as a spacer in the exhaust system. Can someone explain the steps to take to dismantle it? Or do you just take a hammer and chisel to it then weld the shaft holes shut. Thanks in advance. Ed Link to comment Share on other sites More sharing options...
BulldogDriver Posted November 10, 2021 Share Posted November 10, 2021 I removed the bits not needed and tapped the 2 holes and put SS bolts in with anti-seize on them. Didn’t touch the pipe for the choke going through the spacer. Ray Link to comment Share on other sites More sharing options...
Jim Cannon Posted November 10, 2021 Share Posted November 10, 2021 The shaft on my '63 heat riser valve was rusted frozen shut for a long time. Someone had gone in there and bent the ears of the flapper open as best they could, but it still provided some restriction. I went in with a hacksaw blade and cut the shaft inside the manifold as close the the sides as I could and took the flapper out (plus the center part of the shaft). In Texas it was no big deal having no heat riser, except in the coldest of winter days. Now up here in the Smokey Mountains, I notice the engine is slow to warm up a lot more and performance is not too good until it does. Once warmed up, it runs great. The '63 heat riser is an integral part of the exhaust manifold. Later years had it as a separate little unit bolted to the manifold, that the exhaust pipe then bolted to. Link to comment Share on other sites More sharing options...
Chasander Posted November 10, 2021 Share Posted November 10, 2021 I used a small cut off wheel and removed the flap and left the shaft Link to comment Share on other sites More sharing options...
60FlatTop Posted November 10, 2021 Share Posted November 10, 2021 Starting in temperatures of the mid to high 30's and lower 40's is where you would notice the lack of the intake manifold heating. I calculated it once based on air density and the fuel charge came out around 20% lean unheated, enough for a slight stumble. Link to comment Share on other sites More sharing options...
RivNut Posted November 11, 2021 Author Share Posted November 11, 2021 Good ideas. My 64 has the separate heat riser. I’ll figure out a way to remove the innards. Or, if someone has one that is frozen, I’ll work about a deal for mine which works freely. No cold enough to check that it closes properly but a heat gun opens it. Link to comment Share on other sites More sharing options...
Wayne R Posted November 12, 2021 Share Posted November 12, 2021 I am getting old--found this -- may help. 1 Link to comment Share on other sites More sharing options...
XframeFX Posted November 22, 2021 Share Posted November 22, 2021 On 11/10/2021 at 4:37 PM, 60FlatTop said: Starting in temperatures of the mid to high 30's and lower 40's is where you would notice the lack of the intake manifold heating. I calculated it once based on air density and the fuel charge came out around 20% lean unheated, enough for a slight stumble. Here in Northern Canada, I'm keeping my heat riser intact on my '63. It operates freely but remains closed even during a heat wave. It will open momentarily when revving the engine but will close even when keeping the revs up. The small visegrip I clamped on the weighted side of the wheel will remain in-place until I can continue troubleshooting my rough idle when engine temp is up. Will have wait until spring now. This is probably unrelated to my idling issue. Link to comment Share on other sites More sharing options...
Jim Cannon Posted November 22, 2021 Share Posted November 22, 2021 John, for rough idle I'd look at vacuum leaks at the throttle shaft. They wear and then leak. 1 1 Link to comment Share on other sites More sharing options...
60FlatTop Posted November 22, 2021 Share Posted November 22, 2021 I am with Jim. A rough idle and a stumble would be different things to chase. First on the list is a compression test. An overlooked problem is worn valve guides. Once they wear the valve doesn't sear properly and the seat surface will lose its edge. It can be hard to track down and I have seen only one valve out of 16 wear. really hard to find. The job is for a real nit picker but you can catch it with an oscilloscope or in some instances by comparing secondary voltages to the plugs. When those untenable problems show up on a Nailhead I will remove the rocker arm assembly and wiggle the valve stems with my finger. That's the quick test. 1 Link to comment Share on other sites More sharing options...
RivNut Posted November 22, 2021 Author Share Posted November 22, 2021 (edited) 22 hours ago, Jim Cannon said: John, for rough idle I'd look at vacuum leaks at the throttle shaft. They wear and then leak. To expand a little, worn throttle shafts can be fixed with a bushing kit. I would let a pro with the correct tools do it rather than DIY. Edited November 23, 2021 by RivNut (see edit history) Link to comment Share on other sites More sharing options...
XframeFX Posted November 23, 2021 Share Posted November 23, 2021 10 hours ago, 60FlatTop said: I am with Jim. A rough idle and a stumble would be different things to chase. First on the list is a compression test. An overlooked problem is worn valve guides. Once they wear the valve doesn't sear properly and the seat surface will lose its edge. It can be hard to track down and I have seen only one valve out of 16 wear. really hard to find. The job is for a real nit picker but you can catch it with an oscilloscope or in some instances by comparing secondary voltages to the plugs. When those untenable problems show up on a Nailhead I will remove the rocker arm assembly and wiggle the valve stems with my finger. That's the quick test. The retiree that rebuilt my original AFB this summer does throttle shaft bushings. I brought him a switch-pitch throttle shaft to swap during the rebuild. No re-bush required, all good. All ignition replaced with new, including new obsolete Bosch sparkplugs @ .050" Compression test OK. Sealed Power RP3173 Pushrods spin freely, A Sealed Power HT-896 lifter or two clatters on startup for a while after having not run for a while. Cold idle OK off the fast idle cam with choke fully open. Alternator light comes on is how slow the idle is until warm. However, once warmed-up, it has a slight lump with me feeling it over under the hood. It's when I have it in Drive waiting at a red light that its most noticeable, annoying. I have it improved but, still unacceptable to my standards. I'll check the sparkplugs next. They were sooty black at the start of my trouble-shooting. No silver bullet, Thanks all. Link to comment Share on other sites More sharing options...
RivNut Posted November 23, 2021 Author Share Posted November 23, 2021 According to Dennis Manner, the original 63 cam was pretty aggressive. You might not have any issues other than just not liking the aggressiveness of that original grind. In an issue of the Riview (if I had an idea which one,mid post it) Dennis Manner wrote an article about the cams that Buick used in the 63 - 66 nailhead. Very interesting. 1 Link to comment Share on other sites More sharing options...
EmTee Posted November 23, 2021 Share Posted November 23, 2021 11 hours ago, XframeFX said: I'll check the sparkplugs next. They were sooty black at the start of my trouble-shooting. Sounds like it's running rich... Link to comment Share on other sites More sharing options...
60FlatTop Posted November 23, 2021 Share Posted November 23, 2021 13 hours ago, XframeFX said: unacceptable to my standards. My standards are based on what a 1960's professional person would lay out around $5,000 for. Sometimes I just shake my head and think a car never would have made it off the showroom floor running like this. But there are so many poorly running ones they get based on a different standard. I have been at more than a couple of cruise night and heard someone say "Wow! Sounds like it has a cam in it!" when a crappy running car is started. A few years ago I threw out a bag of sooty AC44 plugs. I have been using 45's in my GM cars for years. Recently I have turned to NGK plugs. I set the AC plug on the parts counter and ask to match it up. I figure if they run well in a V12 Jaguar they will do well in anything, has worked for me. Don't overlook wiggling the valve stems. It is easy to do. My cardiologist and I had a lot of fun when he first bought his office Ultrasound machine. It works an awful lot like an oscilloscope. Your diagnostics would be greatly enhanced with one of the newer, quite inexpensive ones. The learning curve is steep with those. I had a big Allen unit but generally use a simple inductive secondary side voltmeter on each wire these days. That can narrow issues down to the cylinder level. Then you can expand to the valves, intake runner, carb section, and so on. It's fun but you have to stay with the very basic functions. Making things too complicated can cause one to overlook a problem. Link to comment Share on other sites More sharing options...
65VerdeGS Posted November 23, 2021 Share Posted November 23, 2021 I'm with Bernie on valve guides being a possible cause for rough idling. In my case it was a 327 in a Chevy that ran excellent overall but had a rough idle. After chasing possible vacuum leaks, ignition, and carb, it turned out to be oil getting into the cylinders because several valve seals had dried out. Replacing the seals fixed the idle problem, along with blue puff on startup. Link to comment Share on other sites More sharing options...
65VerdeGS Posted November 23, 2021 Share Posted November 23, 2021 15 hours ago, RivNut said: According to Dennis Manner, the original 63 cam was pretty aggressive. You might not have any issues other than just not liking the aggressiveness of that original grind. In an issue of the Riview (if I had an idea which one,mid post it) Dennis Manner wrote an article about the cams that Buick used in the 63 - 66 nailhead. Very interesting. Hi Ed, I don't recall the article from Dennis Manner on nailhead cams. Will have to look in my trove of Riview back issues. If you come across the article, please post it. Thanks! 1 Link to comment Share on other sites More sharing options...
RivNut Posted November 23, 2021 Author Share Posted November 23, 2021 Some digging and I came up with it. Volume 5, Number 1, Page 16. 1 Link to comment Share on other sites More sharing options...
XframeFX Posted November 24, 2021 Share Posted November 24, 2021 On 11/22/2021 at 6:33 PM, XframeFX said: I'll check the sparkplugs next. They were sooty black at the start of my trouble-shooting. Sparkplugs. They didn't tell any story as they were all black. I pulled the 4 on the driver's side just now and all are except #6 are tan. Will see if the other side cleaned up with my summer mileage tonight. Small steps. I noticed the Shop manual reminded me that the heat riser for '63 is integral to the manifold. I replaced a cracked one in the '80s. It also indicated to load the spring 1/2 turn to the anchor pin. I will check mine as it appears too strong, won't fall open. Also, missing the anti rattle spring. 17 hours ago, RivNut said: Some digging and I came up with it. Volume 5, Number 1, Page 16. Thanks Ed. wonder if 2 and 4 BBL called for different camshafts. Mine is early '63. Also, all full size '63 Buicks had the 401? Even the base LeSabre? Link to comment Share on other sites More sharing options...
60FlatTop Posted November 24, 2021 Share Posted November 24, 2021 The shop manual shows a diagram of the fuel passages through the intake manifold. Match the darkened plugs up with their runners and it may lead you to one side of the carb that is feeding a little rich due to some malfunction in the barrel feeding the runner. I like the digital manuals because you can print the pages for your job and scribble notes and readings on them. Print that manifold picture and label the runners black, white, or tan. One more level of insight. 1 Link to comment Share on other sites More sharing options...
XframeFX Posted November 25, 2021 Share Posted November 25, 2021 On 11/24/2021 at 11:35 AM, 60FlatTop said: The shop manual shows a diagram of the fuel passages through the intake manifold. Match the darkened plugs up with their runners We can all trouble-shoot be it process of elimination which I've been using or, tapping resources "been-there-done-that"! So, the sparkplugs are saying something this time. Plugs #2, 3, 5 & 8 have tan electrodes which are fed from the driver's side plenum. The Passenger side plenum has plugs that vary from sooty black (two) to a dark tan and a fourth with a tan spot on a black electrode. Plug #7 had oil on the outside and upon re-installation, oil in the recessed cavity, nowhere else. I can't imagine where it came from. I'm sure I did not remove the valve cover from the last time I checked the plugs. Still with my lousy idle at temperature and now this, I'm about ready to ditch my recently rebuilt original AFB and splurge for a new E-Clone 1407 performer carb and swap the top to use the original air filter, period. Back to the Heat-Riser valve, the shop manual states to not tamper with it, LOL. Thanks Bernie. Link to comment Share on other sites More sharing options...
EmTee Posted November 26, 2021 Share Posted November 26, 2021 So, the spark plugs suggest that something is wrong with the passenger side idle circuit...? Seems like looking at the carb is the next logical step. Link to comment Share on other sites More sharing options...
60FlatTop Posted November 26, 2021 Share Posted November 26, 2021 The next step would be looking into the carb while at idle to compare to see if any fuel is dripping from the venturi nozzles or near them. There should be none. If there is it could be your float level or a bleed port. The idle jets should be close at around 1 1/2 turns each. Screw them both back in to see where they are. I like to count by 1/2 turns, seems easier. 3 half turns should seat them both. All the fuel should be coming from the idle port below the throttle plate. If you see any droplets above while running it is a problem. The one oily cylinder is one that I would pop the rocker arm assembly off and wiggle the valve stem with my finger. Being at the rear some valve train oil could be seeping down. Don't rule out anything. A old squashed transmission mount could divert oil to the valve area and away from the head drain holes. Or affecting the float level. 1 Link to comment Share on other sites More sharing options...
EmTee Posted November 27, 2021 Share Posted November 27, 2021 9 hours ago, 60FlatTop said: A old squashed transmission mount could divert oil to the valve area and away from the head drain holes Or maybe the drain hole on that end of the head is blocked (or partially obstructed) by something (e.g., piece of old valve cover gasket)? Link to comment Share on other sites More sharing options...
XframeFX Posted November 27, 2021 Share Posted November 27, 2021 On 11/26/2021 at 9:38 AM, 60FlatTop said: The one oily cylinder is one that I would pop the rocker arm assembly off and wiggle the valve stem with my finger. Thanks All. Will do that too but going to focus on the AFB, specifically the passenger side primary barrel. It might fix that rough idle at temperature as well. Float bowl over-flow (dripping) was occurring before the rebuild. I think my local rebuilder basically did an ultra-sonic cleaning and threw in a kit. I will take it back to him as I paid for the service to be 100% He may have charged me extra to swap out that primary shaft which is nothing while apart. I tinker with DIY but at this point want turn-key results. I'm considering a new Edelbrock #1411. At 750 CFM, too big for a 401? Appears to be calibrated for a BBC 454 but nailheads prefer big carbs? Link to comment Share on other sites More sharing options...
telriv Posted November 27, 2021 Share Posted November 27, 2021 There was a guy on the V8buick.com forum who was making a copy of the heat riser for the 400/430/455 engines. Don't know IF he has any left or planning on making any more. Turn out it was EXACTLY the same as the "Nail" except the studs were 7/16ths. as opposed to 1/2". All that was required was to drill the holes in the cast replacement piece to 1/2". Tom T. Link to comment Share on other sites More sharing options...
Wayne R Posted January 5, 2022 Share Posted January 5, 2022 (edited) Thought i would follow on with this Heat Riser , that Ed asked a few weeks ago, in the last few days i suspected my current riser was not correct or partly blocked , so like with other Buicks i have previously owned, checked this one , and removed it ,. Living in Australia did not really require it because of temps warm temps here. A very easy job to do, when you remove the 2 bolt nuts and lower the holding bracket, the housing holding the flap and spring just drops down as a complete unit, you then just cut the flap axle with a hacksaw blade on the inside, place a blade threw the housing and cut at axle ends, then the whole axle and flap fall out ,then all that is required is to have the 2 holes, welded,--then remount and slide back on, and bolt up.-.--Note my flap was jambed at about 60-70 degress angle not good.---a few photos./ Edited January 5, 2022 by Wayne R (see edit history) Link to comment Share on other sites More sharing options...
RivNut Posted January 5, 2022 Author Share Posted January 5, 2022 I guess that Christmas got in the way and I did not respond to show you what I did to a heat riser to convert it into a spacer. Here's what I did with a sawzall and a stone and my drill. I've yet to smooth it up with a grinder. That's the gasket that Tom M. gave me the part number for. Ed 1 Link to comment Share on other sites More sharing options...
Wayne R Posted January 5, 2022 Share Posted January 5, 2022 Thats great Ed,, strange though this car never had a gasket at the manifold top end, and my other Rivieras never did years back, so i left mine left metal to metal, terrific job with yours though.- Ed,--Thank you. Link to comment Share on other sites More sharing options...
RivNut Posted January 5, 2022 Author Share Posted January 5, 2022 The manifold from which I took this part did have a gasket. I'll have to look in the chassis manual for an illustration. Link to comment Share on other sites More sharing options...
telriv Posted January 5, 2022 Share Posted January 5, 2022 Originally from the factory it was a metal-metal fit. Over the years the metal mating surfaces on the manifold & heat riser get corroded from the heat & years of heating/cooling cycles. The correct way to perform this task is to take the manifold & heat riser & have them resurfaced to make a like new flat area to seal against exhaust gases. The quick cheap way is a gasket. They both serve the same purpose to prevent an exhaust leak. Tom T. Link to comment Share on other sites More sharing options...
Wayne R Posted January 5, 2022 Share Posted January 5, 2022 Thanks for that TomT, i actually used a flat file on the flat areas , and finished with 120 wet dry paper. no leaks now good. regards. Link to comment Share on other sites More sharing options...
telriv Posted January 5, 2022 Share Posted January 5, 2022 Glad to hear it worked out for you Wayne. Tom T. Link to comment Share on other sites More sharing options...
OldGerman Posted April 5 Share Posted April 5 In the process of removing the flapper from the exhaust manifold, it seems the biggest challenge is to replace the flange bolts. Easy to cut the flapper shaft and drive out the axis, cutting a thread in the holes to plug them with a screw. But this damm 1/2 bolts won't come out. I have no acetylene gas burner, just a propane burner with no success. Now I let the whole thing soak in vanilla yogurt (no, that's 60% acetic acid). I hope it can penetrate and loosen the rust a bit, then we'll move on.. Link to comment Share on other sites More sharing options...
1965rivgs Posted April 5 Share Posted April 5 You need more heat...ideally oxy/acet...try MAP gas, a low cost alternative, which you should be able to use with your current propane head. If the top of the studs are protruding above the manifold flange, and are rusty and corroded, try to clean those up as much as possible before you back out the studs. Or, if you can get access to one or both of the studs from above, drill a hole into the stud from the top so it can collapse. Otherwise, if you loosen the stud and try to turn out the corroded upper part of the stud through the threaded hole in the manifold, it will snap the manifold flange because the stud wants to force the hole larger. Ask me how I know! Tom Mooney 2 Link to comment Share on other sites More sharing options...
RivNut Posted April 5 Author Share Posted April 5 I have a friend who works for the Union Pacific Railroad. He took a pair of exhaust manifolds into the UP shop to have the studs removed. He said the guy who got them out said that he’d never had to use that much heat before. And that he’d never do it again. I’m thinking you’ll need to get those puppies red hot to get them out. 1 Link to comment Share on other sites More sharing options...
Seafoam65 Posted April 5 Share Posted April 5 Take the part to a muffler shop and let them get them out with their torch. 1 1 Link to comment Share on other sites More sharing options...
OldGerman Posted April 5 Share Posted April 5 Muffler shops are not so common here in Germany, but I will find a shop which has the right equipment. It's a hobby for me, so I can not buy everything for single use. But thank you all for sharing your experience and tips. Most shops are not used to repair old rusty stuff, but just repairing 3 years old lease cars and exchanging new parts. Need to find someone who is willing to support rusty stuff. Link to comment Share on other sites More sharing options...
EmTee Posted April 5 Share Posted April 5 The other option would be to drill them out. Personally, I'd try to find someone with an oxy-acetylene torch first. Before drilling, you'll need to cut them flush and then center-punch the center of the stud to keep the drill bit from walking off-center. The trick is to start small and go slow, increasing the drill bit size without damaging the threads in the manifold. 1 Link to comment Share on other sites More sharing options...
XframeFX Posted April 7 Share Posted April 7 On 4/5/2024 at 9:00 AM, 1965rivgs said: .try MAP gas, a low cost alternative, which you should be able to use with your current propane head. Here in North America, it's the yellow bottle for more heat over the blue propane bottle. Check your stove pipe while the manifold is out Frank. Plug one end and blow on the other end. Mine leaks, rust?. I think it's a spiral tube so can't shove another brass tube inside. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now