Frank Wilkie Posted September 13, 2021 Share Posted September 13, 2021 Has anyone had any experience in using a 8 volt battery in a 1934-35 Buick? Would the bulbs hold up? Why I'm considering it is because the starter seems a little draggy and takes a long time for it to start. It was rebuilt before I purchased the car. I have cleaned the negative battery connection to the frame and of course the 6 volt battery connections. Link to comment Share on other sites More sharing options...
Rock10 Posted September 13, 2021 Share Posted September 13, 2021 I don't think the generator would charge it. Link to comment Share on other sites More sharing options...
Steves Buick Posted September 13, 2021 Share Posted September 13, 2021 Make sure you have the proper size cables, run your negative battery cable directly to the starter. I don't a real need for a 8 volt battery if everything works. I use a 6 volt optima and it's fine. 3 1 Link to comment Share on other sites More sharing options...
Matt Harwood Posted September 13, 2021 Share Posted September 13, 2021 To make a 6 volt car start using 6 volts: 1. Load test battery to be sure it's putting out adequate voltage and current. As mentioned, Optimas really do pack a wallop. 2. Big battery cables. They should be as big as your thumb. 3. Clean all grounds. 4. Add a ground cable from battery ground to starter housing. 5. Add a ground cable from engine block to frame. 6. Clean all grounds (yes, I said it twice). 7. Rebuild starter if necessary (new bushings can make a world of difference). Always remember that old cars cranked much slower than modern cars, yet they still fired. My '35 Lincoln turns over at like 30 RPM and every Packard 356 I've had grinds so slowly that you'd think the battery is already dead. Totally normal. Also make sure your ignition system is in top shape. The starter is pulling most of the battery's power so any flaws in the ignition system will be revealed during cranking. If you're running an electric fuel pump during cranking, make sure it isn't connected to the ignition for power--pull your power from someplace else, there's not enough to spare if you pull it from the ignition switch. This is a solvable problem. 8-volt batteries are band-aids at best. Fix it right and you won't have any more problems. 10 1 Link to comment Share on other sites More sharing options...
Frank Wilkie Posted September 13, 2021 Author Share Posted September 13, 2021 Thank you for all the input.. This assured me of what I had expected to hear.. I normally don't like to make any changes from originality.. Staying 6 volt.. 4 Link to comment Share on other sites More sharing options...
37Special Posted September 13, 2021 Share Posted September 13, 2021 (edited) Optima batteries helps a lot. I'm new to pre war so maybe I'm not used to 6 volt as much but I installed an optima and changed my cables and wow! Huge improvement! Edited September 13, 2021 by Nichalicious (see edit history) 2 Link to comment Share on other sites More sharing options...
Frank DuVal Posted September 14, 2021 Share Posted September 14, 2021 If one was to put in an 8 volt battery, to charge it you have to adjust the regulator or third brush generator up to 9.4 volts to make it charge! That's why I say fix it and keep the 6 volt system. Less stress on the charging circuit. Make or buy 2/0 awg cables. 4/0 if you can find them. Link to comment Share on other sites More sharing options...
Morgan Wright Posted September 14, 2021 Share Posted September 14, 2021 7 minutes ago, Frank DuVal said: Make or buy 2/0 awg cables. 4/0 if you can find them. Yeah 6V means the amps double so you need 0 or 2/0 I think 4/0 is overkill. Any way, you need thicker cables than with 12V 1 Link to comment Share on other sites More sharing options...
Oldtech Posted September 14, 2021 Share Posted September 14, 2021 My experience with 8 volt batteries is limited, but a few years ago we thought we should get a couple for our museum cars that we run. They cranked the car wonderfully - for the first year, then they lost power badly - all of them. We had noticed that they seemed lightweight compared to a good 6 volt. So, back to 6 volts and they are fine. 1 Link to comment Share on other sites More sharing options...
Larry Schramm Posted September 14, 2021 Share Posted September 14, 2021 Go back to the correct size cables. Be sure to have clean contact surfaces that the cable terminals attach to. To help to be sure of a good mechanical connection of the cable terminal to the cable, solder the terminal to the cable after crimping. Soldering fixes a lot of crimping issues, both immediately and over time. 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now