Buick35

Evapor-rust as cooling system rust remover

Recommended Posts

I've read where using evapor-rust as a rust remover in the cooling system works well. My system takes 28 pints of coolant and I only bought 2 gallons or 16 pints.Would that be enough to work or should I buy another gallon,or just add a gallon of water? Thanks,Greg.

Share this post


Link to post
Share on other sites
Just now, Alex D. said:

 I would buy another gallon and not dilute.

 

This.

 

It has the same viscosity as water and I used Ed's advice to just use straight Evapo-Rust to clean out cooling systems. Be sure to use some kind of filter on the upper hose to catch all the stuff that's going to come loose. Grimy's suggestion of a woman's pantyhose foot is a good one so all that trash doesn't clog your radiator. Drive around on it that way for a few weeks, cleaning the filter periodically, giving it a few good heat cycles and really let the water pump churn it through there. You'll be amazed by what comes out!

Share this post


Link to post
Share on other sites

Thanks,I'll buy another gallon. I just drained it good and added the two. Greg.I'm surprised Tractor Supply had it.

Share this post


Link to post
Share on other sites

I followed Ed’s advice and drained, then flushed twice before adding the Evaporust. I bought a 5 gallon pail from Home Depot (special order) for $80. I ran it for 6 weeks driving the car almost every day. By the end of the first week, no more overheating. By the end of 6 weeks, my engine and radiator were as clean as from the factory!

 I drained the Evaporust and put it in another car which I plan to run another 4-6 weeks.

 GREAT STUFF! 

 Thanks Ed!!!

 

Wayne

  • Like 1

Share this post


Link to post
Share on other sites
6 hours ago, Phillip Cole said:

Does straight Evapo-rust work better than their radiator flush, Thermocure?

They are different products, but whether they act in the same way, I don't know. Evapo-Rust is a "proprietary non-hazardous chelating agent" plus a little detergent in >83% water. Thermocure is fertiliser (diammonium phosphate) plus sodium salts in water. They are both acid (pH 6.0-7.0) but I suspect Thermocure is about scale and so on in the radiator more than rust.

Share this post


Link to post
Share on other sites

I used EvapoRust at the suggestion of Ed in Mass, as I recall. I think it worked pretty well, and you don't have to worry so much about caustic deterioration of gaskets and such. Ed says he uses it straight through the entire warm season. I just tried it straight for a few weeks to be cautious. No leaks or damage. Next year I'll probably use it for a couple of months and if that works, I might do the following year for the whole warm season like Ed.

 

I did use the EvapoRust ThermoCure product for a couple of weeks before using the EvapoRust. The products aren't the same, but I think they may be related. They both work better the more you drive the car.

Share this post


Link to post
Share on other sites

I was looking at Evaporust at a vendor's booth years ago and was talking to the vendor when a bystander said you might as well use Coke sweet drink.  I use Evaporust to clean small parts from my 28 DB. Just dunk the parts and leave over night. It is really good for  irregular shaped object.   Excellent for cleaning valuable and antique stuff.. It is better to put object to clean in a container with a cap.   to prevent evaporation . Check periodically for cleanness. Wash objects with water and blow dry immediately. If you did not wash immediately dot be afraid . The objects can remain for weeks until washed. Liquid can be reused until it turns black.. If the objects look black after removing from liquid just brush with a fine wire brush. .It is the best invention next to slice bread 

Share this post


Link to post
Share on other sites
5 hours ago, mercer09 said:

I use vinegar in my cooling systems. cheap and effective.

and it attacks everything, not just the rust. Copper, brass, solder, clean iron, you name it.

Share this post


Link to post
Share on other sites

You may want to use a little caution with the evaporust. I had a pair of aluminum heads on a car that were heavily corroded but not leaking. When i used the evaporust, it did a great job removing the rust and corrosion but then the heads leaked. I'm sure the heads would have eventually started to leak but the process was speeded up with the Evaporust.

Share this post


Link to post
Share on other sites
1 hour ago, Shipping reccomendations said:

You may want to use a little caution with the evaporust. I had a pair of aluminum heads on a car that were heavily corroded but not leaking. When i used the evaporust, it did a great job removing the rust and corrosion but then the heads leaked. I'm sure the heads would have eventually started to leak but the process was speeded up with the Evaporust.

 

I suspect the Evapo-Rust merely removed the corrosion that was preventing the leak.

  • Like 1

Share this post


Link to post
Share on other sites
1 hour ago, Matt Harwood said:

 

I suspect the Evapo-Rust merely removed the corrosion that was preventing the leak.

 

Matt is 100 percent correct.

  • Like 1

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...