Sign in to follow this  
Mssr. Bwatoe

H-V-12 VIBRATION DAMPNER / BALANCER

Recommended Posts

Posted (edited)

Hi gang, I need to repair my balancer, the weight spins on the unit, I recall 

an article in TWOTZ about repairing...can anyone chime in on the direction.==the plates are sandwiched between fiber washer as seen in pic  pt 06h-6366     

like an automatic trans mission clutch plate, but for no metal lining--probably some form of cork?

 

hey 40 Tom  !!

 

IMG_3291.JPG

IMG_3286.JPG

IMG_3280.JPG

Edited by Mssr. Bwatoe (see edit history)

Share this post


Link to post
Share on other sites
Posted (edited)

I've rebuilt a couple of those.  Best I remember I made some new fiber washers from some gasket gasket material but not cork.   I think cork might be too soft.  

image.jpeg

image.jpeg

Edited by Ken/Alabama (see edit history)

Share this post


Link to post
Share on other sites

Yes, can be. Hold the unit in a vice, carefully.  Just press the ring thing down against the spring pressure with a fork arrangement and flick the horse shoe clip out.. Try not to loose sight of where the clip ends up. Good luck! 

Share this post


Link to post
Share on other sites
On April 30, 2019 at 4:26 PM, Michael L. said:

Are those little c clips hard to get off in order to disassemble this balancer?

Mike L.

I used a valve spring compressor to remove them. 

Share this post


Link to post
Share on other sites

Hi guys. What is the symptoms of a faulty balancer?  I have an engine vibration on deceleration but no engine misfire and plenty of power.

Thank you for any suggestions,  George

Share this post


Link to post
Share on other sites

Look at engine mounts, sagged settled old motor mounts.....My balancer weight is loose, spins free...

I dont know what happened..still drives fine/

Share this post


Link to post
Share on other sites

I was thinking about the engine mounts. I replaced them maybe 15 years ago with rebuilt ones from Richard Hommel. I wasn't sure of the quality of them at the time. I'll check mine out if it ever stops raining here in the northeast. Thank you for the reply, George.

lincoln11.8.jpg

Share this post


Link to post
Share on other sites

I'm glad you mentioned that, we have a problem, with mount availability, I suspect sagged motor mounts 

that allow  the metal inside to rest on the inner shell is a source of a lot of Lincolns that sound like a truck

inside..Do you have a good source for them, I think mine were made by Warren Rice 45 years ago!! I would renew them in a second

if they were done well..

Share this post


Link to post
Share on other sites
4 hours ago, Mssr. Bwatoe said:

Hey Ken, Did you paint the inner side of the balance plates??

 

I did but not in the recess where the fiber washers go and also keep paint out of the holes for the pins and springs.  

  • Like 1

Share this post


Link to post
Share on other sites

If you want improved performance, have a hub machined to mount the crank pulley, and use a Chevy balancer.  GM balancer needs to be honed a bit to fit.  You then need to fab a fan adapter, or go with electric fans.  Not stock, but would take a careful eye to tell the difference.

Abe

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
Sign in to follow this