Fleetwood Meadow Posted September 21, 2018 Share Posted September 21, 2018 (edited) So now that the weather is getting cooler I think it’s time to fix the smoking issue my ‘51 Meadowbrook has. Has 48k miles. I got it 4 years ago with 43k on it. It hadn’t been on the road since 1973. It uses about a quart every 100-150 miles, depending upon if I go about 40mph. I can use a quart if I go 55-65 for about 15 minutes. At those speeds I get a faint smoke out of the tail pipe. During deceleration I get it too. I was going to replace the seals but i can’t find any and don’t see them in the book. Does this engine not have seals? I have been told it’s the oil ring on the pistons. I have been told it’s the valve guides. Is there a way to definitively know prior to taking off the head? My dry compression test was around 95 across the board. I didn’t do a wet compression test, mainly because I’m new to a lot of this and didn’t know I was supposed to do it. Edited September 22, 2018 by Fleet Meadow (see edit history) Link to comment Share on other sites More sharing options...
Guest Posted September 21, 2018 Share Posted September 21, 2018 (edited) Are you sure you are not leaking any oil, with that kind of consumption you should be seeing a real fog behind your car. I would suspect that your oil rings aren't doing their job and therefore the compression rings are overloaded which would account for your good compression. Another possibility would be worn valve guides. A vacuum test would confirm this. You really need a wet and dry compression test, preferably a leak down test. Having a vacuum gauge hooked up when the engine is running would give you a lot of information, What does your coolant and what does the oil in the engine look like. What weight of oil are you consuming, When I started driving my Grandfathers Pontiac (99,000 miles) it was burning quite a lot of oil. He had started using heavier oil to stop this and obviously it was not working. A mechanic in the dealership where I worked said to go to a lighter oil as it would not overload the rings. Over a couple of oil changes I went from 40wt to 30wt to 20wt and the consumption lessened. But within five years (50,000 miles) I had to replace all the valves with oversize ones and ream the guides. I should have opened the engine in the beginning and fixed it right. Long distance diagnosing and advice is easier with more data. Edited September 21, 2018 by Guest (see edit history) Link to comment Share on other sites More sharing options...
Bud Tierney Posted September 21, 2018 Share Posted September 21, 2018 (edited) Concur that's way way too much oil depletion for burning in comb chambers or exhaust without having real billows of oil smoke out behind you... Assuming you're not leaking it out (no puddles in the driveway?? look at the underside behind the motor; don't be surprised if you find your oil liberally coating everything).. As recommended above, sounds like a prime candidate for opening up... If you replace rings, at least carefully check the bearings; if they have any slack at all putting in new rings=more downward force on bearings, and if slack they'll get very slack very quickly..., Forgot these are (in)famous for disgorging the first quart of oil...before disemboweling, if no visible substantial leak(s), try running one quart low to see if reduces consumption... Edited September 21, 2018 by Bud Tierney Senility (see edit history) 1 Link to comment Share on other sites More sharing options...
Rusty_OToole Posted September 22, 2018 Share Posted September 22, 2018 If an engine has worn rings it will smoke when you accelerate, if it is valve guides it smokes when you lift off the gas pedal. When in good shape they could still burn a quart of oil in 500 miles and that was normal. How many miles on the car? How is your oil pressure? Tinindian has a good point, heavy oil won't cure a worn engine. But if the car was sitting and the rings got gummed up light oil and a few long drives, like over 100 miles, might free them up. I also agree that you are likely leaking a lot of oil. If the engine is a greasy mess you want to clean it then go for a drive and inspect for fresh leaks. But you may be able to see where it is leaking by where it is greasy. Link to comment Share on other sites More sharing options...
Fleetwood Meadow Posted September 22, 2018 Author Share Posted September 22, 2018 It has 48k on it. I got it 4 years ago at 43k. Last time it had been on the road was 1973. The rear of the engine does have a lot of oil on it. Actually it’s more on the transmission after the draft tube. Because it’s covered in oil i get small puddles under the car. Small as in 1.5-2” puddles overnight. They show up in full size after about 2-3 hours of sitting. I have been using 15W-40 in it. When I have 10W-30 and SAE 30 in it it lost the same amount of oil. On normal driving it does not smoke. After 50mph I see random puffs of smoke. At 65 it is a good amount of smoke coming out. Then it puffs at deceleration. Link to comment Share on other sites More sharing options...
Guest Posted September 22, 2018 Share Posted September 22, 2018 If you read post #4 by, Rusty_OTool you have your answer. Leaks and valve guides. Link to comment Share on other sites More sharing options...
hchris Posted September 22, 2018 Share Posted September 22, 2018 I'm thinking if you burn a lot of oil the plugs will be fouled, or at least have a lot of carbon on them. Try putting a catch can over the breather / draft tube and see what shows up. Link to comment Share on other sites More sharing options...
Rusty_OToole Posted September 22, 2018 Share Posted September 22, 2018 With under 50000 miles and good oil pressure it should not be smoking like that. I suspect that while in storage the rings got stuck and the seals dried out. A few long drives might straighten it out, especially if you add some lubricant to the gas and oil, like Seafoam. Otherwise you will have to tear it down for a ring and valve job and new crankshaft seals. 2 Link to comment Share on other sites More sharing options...
Fleetwood Meadow Posted September 23, 2018 Author Share Posted September 23, 2018 (edited) So I did some research today and found out it smokes at acceleration as well so I’m leaning towards the rings. I know I was asked but forgot to answer, my oil pressure is correct for the speed, essentially it’s 35 at 35, etc. I did some highway driving and some rapid accelerations. Overall it was a fun day of driving. Edited September 23, 2018 by Fleet Meadow (see edit history) Link to comment Share on other sites More sharing options...
cahartley Posted September 23, 2018 Share Posted September 23, 2018 You can't rule out stuck rings just yet though. I would add a can of oil detergent additive and put a few hundred hard miles on it. Just loafing around won't fix anything. The worst that can happen is it starts burning MORE oil at which time it's a nearly sure thing the rings have had it.......or worse. Link to comment Share on other sites More sharing options...
Fleetwood Meadow Posted September 24, 2018 Author Share Posted September 24, 2018 I wasn’t ruling out the rings. In fact I am believing that is what the issue is. When it comes to ring size, how do I determine the right ones? I don’t believe the engine has ever been rebuilt. I’m pretty new to rebuilding an engine so ordering parts is where I lack experience. Link to comment Share on other sites More sharing options...
Spinneyhill Posted September 24, 2018 Share Posted September 24, 2018 You will order rings after taking off the head and measuring the bore. Give it a bit longer. Go for a couple of 100 mile drives, with lots of hills along the way. 1 Link to comment Share on other sites More sharing options...
Fleetwood Meadow Posted September 24, 2018 Author Share Posted September 24, 2018 I’ve gone 5k miles on back roads and highways. That’s not enough? Link to comment Share on other sites More sharing options...
Stude17 Posted September 24, 2018 Share Posted September 24, 2018 Can you be sure that the engine had only done 43,000 miles when you got it? From the symptoms you describe I would suggest it has done a lot more and it is time to rebuild. Link to comment Share on other sites More sharing options...
Spinneyhill Posted September 24, 2018 Share Posted September 24, 2018 (edited) 37 minutes ago, Fleet Meadow said: I’ve gone 5k miles on back roads and highways. That’s not enough? Arrr. Yes, that is enough! So since you bought it, the consumption has not decreased? Have a look at @hchris's suggestion to check for blow-by. If there is blow-by with that much oil consumption, you should see a bit of smoke and under the car would be a mess behind the bottom of the breather tube. Edited September 24, 2018 by Spinneyhill (see edit history) Link to comment Share on other sites More sharing options...
MCHinson Posted September 24, 2018 Share Posted September 24, 2018 I would really suggest you clean and degrease the bottom of the engine well. I would then check for leaks after driving it a bit. From your description, I think you may be leaking more than you are burning. Also, what color is the smoke? Is it blue or is it black? I once thought I had some oil burning in an engine and it turned out that it was leaking oil, but was running rich giving the car black smoke under acceleration. With the oil leaking stopped and the carburetor fixed, the car does not use any oil and it does not smoke anymore. Link to comment Share on other sites More sharing options...
Rusty_OToole Posted September 24, 2018 Share Posted September 24, 2018 (edited) Stop and go, short trips won't free up the rings. Years ago when I worked in a garage we had a customer who bought a beautiful 1971 GMC six cylinder half ton. It was about 15 years old and had been off the road and in storage for 10 years. It ran beautifully but burned oil. After 2 years he had us tear the engine down, it was in perfect shape except the rings were frozen in the pistons. You could see circles of rust on the cylinders where the rings rusted to the cylinders while it was in storage. We installed new rings and it was good as new. I believe we had the head done while it was off, so a ring and valve job. The customer was a carpenter who used the truck locally, never for long trips. If he had taken it out on the hiway for a few 100 or 200 mile drives the rings might have come free. I know of other cases where this happened. One was a local collector who bought a Morris Minor convertible in California and drove it back to Canada. When he started out it burned a quart of oil in 100 miles. By the time he got home it did not burn any oil at all. Edited September 24, 2018 by Rusty_OToole (see edit history) 2 Link to comment Share on other sites More sharing options...
trini Posted September 25, 2018 Share Posted September 25, 2018 Breather tubes can get plugged up too and make the smoking worse. The reading on the odometer may not be accurate, most likely more than it says. Given that the engine sat for a long time it is most likely stuck rings and not so much worn guides. Sometimes by removing one quart of oil from the sump and replacing with a quart of transmission fluid and run engine , may be for a fifty miles helps to dislodge the rings. Also idle engine at about 1000 R.P.M while feeding transmission oil through the carburetor works. The spark plugs will give a good indication of the condition of the engine. If all fails tear the engine apart and do a complete rebuild. Do not forget to look for a reputable rebuilder. Link to comment Share on other sites More sharing options...
Fleetwood Meadow Posted September 25, 2018 Author Share Posted September 25, 2018 On 9/24/2018 at 1:07 AM, Spinneyhill said: Arrr. Yes, that is enough! So since you bought it, the consumption has not decreased? Have a look at @hchris's suggestion to check for blow-by. If there is blow-by with that much oil consumption, you should see a bit of smoke and under the car would be a mess behind the bottom of the breather tube. The oil consumption has started this year. Before that it was fine, a quart once in a while. There is a lot of mess behind the bottom of the breather tube. And I get smoke out of that tube, both tubes actually. Link to comment Share on other sites More sharing options...
Fleetwood Meadow Posted September 25, 2018 Author Share Posted September 25, 2018 Today and tomorrow will be raining pretty hard so I can’t play with it too much but I’m going to take it out on the highway a little and see if it gets better. I do tend to drive back roads instead of the highway because I don’t like the higher rpm of the engine working the 3 speed transmission. Link to comment Share on other sites More sharing options...
Spinneyhill Posted September 25, 2018 Share Posted September 25, 2018 (edited) Did the oil consumption increase fairly suddenly? It sounds like it will not get better. You have a lot of blow-by indicating ring problem(s), maybe even a piston problem. Edited September 25, 2018 by Spinneyhill (see edit history) Link to comment Share on other sites More sharing options...
Fleetwood Meadow Posted September 25, 2018 Author Share Posted September 25, 2018 Yes it seemed like a put a quart in then I drove and looked at the dip stick and it was a quart low. That’s how it started. Link to comment Share on other sites More sharing options...
Grimy Posted September 25, 2018 Share Posted September 25, 2018 I think you *should* have a single action fuel pump and electric wipers, but if you have a double-action pump (fuel + vacuum for wipers), a bad diaphragm in the vacuum side of the pump can cause huge oil consumption. Link to comment Share on other sites More sharing options...
Rusty_OToole Posted September 25, 2018 Share Posted September 25, 2018 Maybe the best answer is a ring and valve job. To do this you will need to take off the head and oil pan, remove the pistons and rods, take out the valves and check them for wear, grind in the valves and knurl or replace valve guides as necessary. Link to comment Share on other sites More sharing options...
Guest Posted September 25, 2018 Share Posted September 25, 2018 Six additions to the original post asking for advice. It's hard enough to help someone and impossible without the whole story. Who knows how many more facts may come along. As I am into the last quarter of my first century I'm too busy to bother with this thread anymore. Fleet Meadow I do wish you good luck. Link to comment Share on other sites More sharing options...
Fleetwood Meadow Posted September 26, 2018 Author Share Posted September 26, 2018 Well, for everyone that thinks I’m somehow intentionally screwing around by changing the original post, let me clarify it so you know exactly what I have added. Let me start by stating that it was edited 3 times, not 6. Originally I stated i had compression at 90 psi. But then I found the paperwork and I had between 92 and 96 so I changed it to say 95. Originally I did not have mileage included in the post so I stated that I put 5k miles on the car, got it at 43k and it has 48k. Other than that it is the same as the original post. I also changed it within the first day just after Rusty asked how many miles on it. He was the first to ask and the thread was new enough that I felt it would not create a huge issue that would cause a thread bashing and a like of that thread bashing. I’m apologize that I’m not a professional writer and sometimes I don’t have everything just right when I write it. I will work much harder next time. For all of you that have been calm about this post and actually offered insight I truly do appreciate it and it’s helping me, a young man that is trying to take care of a car that he cares about. Link to comment Share on other sites More sharing options...
Restorer32 Posted September 26, 2018 Share Posted September 26, 2018 Your engine is telling you as gently as it can that it's time for a rebuild. 1 Link to comment Share on other sites More sharing options...
Spinneyhill Posted September 26, 2018 Share Posted September 26, 2018 Your sudden smoking etc. reminds me of my own effort on this. Coming home from the Boxing Day run in 1996, my 1930 Dodge Brothers Eight suddenly started smoking. A lot! It was like a warship smoke screen except blue. I thought it was running well and it wasn't burning discernible amounts of oil. There were no untoward sounds from the engine. So I put in new rings. The very thin ridge was removed from the top of the cylinders and they were honed, in place. (The man stood on top of the block to do this.) The bearings were all in spec. The hardest part of the job was lying on the floor under the engine cleaning the cylinders over and over to remove the oily grinding paste left by the honing, without getting any of it on the crankshaft journals. During honing, the crankshaft was well wrapped to keep it clean, but unwrapping was traumatic to make sure it remained spotless. I was hoping for 10,000 miles before an overhaul. I have nearly got that much now. Link to comment Share on other sites More sharing options...
Rusty_OToole Posted September 28, 2018 Share Posted September 28, 2018 Normal engine life of a 51 Dodge flathead six about 80,000 to 100,000 miles if driven sensibly and serviced regularly. With abusive driving and no oil changes or tuneups you could cut that to 50- 60,000 miles. 50,000 miles of normal driving should not wear out your motor, on the other hand it has been out of commission and you don`t know how it was treated before. If it was mine I would try the Seafoam treatment with light oil a few long drives, at least 100 miles in a day, preferrably more. If that made no improvement I would plan a ring and valve job. For some insight into the service life of this type of engine see this owner`s report of a 1951 DeSoto 8 passenger Suburban. Note that this is a very heavy car with 4:11 gear rear axle. A normal sedan would be easier on the engine. https://www.allpar.com/cars/desoto/suburban-1951.html Link to comment Share on other sites More sharing options...
Fleetwood Meadow Posted September 29, 2018 Author Share Posted September 29, 2018 The point I got out of that story is that previous owners can change or alter a lot of stuff and still call it original, which can indicate unrebuilt to some new buyers. When I bought this car I had never been under the hood of a car that old, hadn’t even heard of a Meadowbrook before I bought it. So by not knowing much about the car I didn’t know what I was looking for specifically when I was getting it running for the first time. Now when I open the engine I will have a better knowledge of what I am looking at. The one thing that makes me weary about rebuilding the car is all of the measurements. Link to comment Share on other sites More sharing options...
Ben Bruce aka First Born Posted September 29, 2018 Share Posted September 29, 2018 Fleet, don't sweat the measurements. On an engine of this era, they don't have to be too precise. I am betting when the head comes off one will see no ov oversize [ .010 or .020 ] markings on the pistons, indicating an original bore engine. If so, or if not so, you should be able to "rent" a set of micrometers from an auto parts store. Check the bore. Check the crank journals. All probably in spec. New rings and new bearings . I probably would just "eyeball" and if nothing obvious jumped out , install new parts and go. That is if the car is only going to be driven a few thousand miles a year. Rusty is spot on on driving . If the engine sounds good, i:e, not noisey, Take some extra oil, hit the freeway, drive about 50 miles at 60 mph or so, check the oil and top up if need be, drive another 50-75, depending on how much oil was needed to top up. Put 200-300 miles on this way. Might not have to open engine. If this does not help, at least you will have an enjoyable afternoon. Ben Link to comment Share on other sites More sharing options...
Stude17 Posted September 29, 2018 Share Posted September 29, 2018 (edited) 6 hours ago, Fleet Meadow said: The point I got out of that story is that previous owners can change or alter a lot of stuff and still call it original, which can indicate unrebuilt to some new buyers. When I bought this car I had never been under the hood of a car that old, hadn’t even heard of a Meadowbrook before I bought it. So by not knowing much about the car I didn’t know what I was looking for specifically when I was getting it running for the first time. Now when I open the engine I will have a better knowledge of what I am looking at. The one thing that makes me weary about rebuilding the car is all of the measurements. Fleet Meadow the thing about these forums is that many people offer advice that may or may not be correct or beneficial. From what I have read on this thread if the vehicle was mine there is no way I would be taking it out on the roads and driving it at high speed and particularly sustained high speed. Considering the amount of oil it is consuming the engine is in need of a rebuild before it gets worse and suffers a catastrophic failure by driving it hard. As for rebuilding the engine I would find a reputable engine rebuilder in your area and speak to them about a rebuild before you start. From my own experiences I think you will be pleasantly surprised by their interest in your vehicle and providing sound advice. Whenever I rebuild an engine I do the dirty work such as cleaning and dismantling and leave the measurements to the experts. It is obvious to me that you enjoy your vehicle so please speak to an engine rebuilder and see what they have to say. Good luck. Edited September 29, 2018 by Stude17 (see edit history) 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now