chistech

32' Oldsmobile Deluxe Convertible Roadster

Recommended Posts

Finished up the mold  and sent it out to CO so joe can make some pours and send me one. The mold will get some more details added later when we have more time but for now what we have is good enough. Did everything I mentioned in my previous post and I also made up a hood prop assembly. The Olds hood is very big and very flimsy with a really lousy way to hold it open. It has a foot attached to the back edge of the inside of the hood and this foot is put on the cowl lacing when you want to hold it open. A slight gust of wind or a little bump and your hood will come crashing down doing a ton of damage to too many thing. I looked at a few commercial units already made but still thought a better mousetrap could be made. 

      Using some 1/2” aluminum channel, some 1/2-1/8” flat, 5/16 steel hex rod, and some aluminum blocks I made up a unit to work with my Olds. I milled some 7/16” slots in the blocks at 19d to match the diameter and angle of the radiator support rods. I made up blocks to go on the top of the support rod blocks with a 1/2” slot milled to capture the 1/2” aluminum channel and flat stock. I bent up hooks on the ends of the hex stock then drilled/tapped the ends for 6/32 stop screw. Then I milled two .140 x2” long slots in the bottom of the channel. The slots are for the 6/32 screws to travel in and control the movement of the two hexagon hooks. The hood prop is held across the two radiator brace rods and the hooks are pulled out slightly when the hood is lifted. The hooks get attached at the center of the hood rear where the hood latch mechanism is. The hood latch rod sits right in the hexagon hook and securely holds the hood. There is a long piece of flat spring steel stock inside the aluminum channel that I put some small bends in so it applies pressure on the hexagon hooks so they don’t rattle or slide out of the channel when pushed all the way in.

A379D99B-7985-4FFB-8A22-95113835658D.jpeg

DB144CD5-34EE-48D6-9DBE-DF6BFACB77DC.jpeg

6D6041AC-260D-4439-BB18-CEB4963CBB1E.jpeg

92C3F447-91C4-4609-A3D8-63FDC255CAB1.jpeg

  • Like 2

Share this post


Link to post
Share on other sites

Forgot to mention she is just about fully assembled finally. There are just two chrome fender spears to go on after the pinstripes which are being done Saturday morning at nine. It’s getting its final cleanup and detailing tomorrow by Gilly and his brother then they will be officially done and signed off on it.

D87EEBE8-2C2A-429D-8D0A-9544EBA9C3D8.jpeg

Edited by chistech (see edit history)
  • Like 9

Share this post


Link to post
Share on other sites

Simply gorgeous.  

The quality and expertise of your restoration will set a new standard at Hershey.  

Truly a pleasure following your build.  Congratulations.  

 

Did you fabricate the hood prop?  I looks nice and sturdy.  I'd like to see your plan on that.

 

Not that you need it, but "GOOD LUCK" at Hershey!!!!  Stunning.

 

Gary

  • Like 2

Share this post


Link to post
Share on other sites
2 hours ago, Gary W said:

Simply gorgeous.  

The quality and expertise of your restoration will set a new standard at Hershey.  

Truly a pleasure following your build.  Congratulations.  

 

Did you fabricate the hood prop?  I looks nice and sturdy.  I'd like to see your plan on that.

 

Not that you need it, but "GOOD LUCK" at Hershey!!!!  Stunning.

 

Gary

Thanks Gary but I’m sure my work is no better than many other cars being shown, it’s mainly that I’ve been documenting my restoration and people have been able to follow along with it. My friend Joe for instance who’s been working on his 32’ Olds sport coupe, has done at least the same level of work but no one has seen it because he does no threads on a forum. I have spoken with the editor of the NAOC magazine about doing a story of our two 32’ Olds, restored at the same time, by two guys who live 1800 miles apart, and who became good friends because of owning their respective cars. Much of what I learned on my Olds came from joe.  I am indented to him for teaching me so much and helping reach the level of restoration I was hoping for. I couldn’t have done it without his help and knowledge. To me, that’s what our old car fraternity is about, people helping people out. Examples like JP giving machining tips to MM or vice versa is what it’s about. If there’s something I know and can share my knowledge with someone, I enjoy doing just that like many others do here.

  • Like 6

Share this post


Link to post
Share on other sites

Gary, I realized I didn’t answer about your question on the hood prop. Yes, it’s my own design and I fabbed it out of odds and ends of material I had in my shop. I tried for the lowest and cleanest profile I could come up with plus I wanted simple but sturdy. I didn’t draw up and plans just went with the thoughts in my head. Of course, working that way got me into the situation I’ve been in for the last twenty years wife my wife! 😂 Actually, I’m lucky as it’s worked out very well so I’ll keep going with what pops into my head as long as I think it out before I act! 

    The prop doesn’t hook under the bottom edge of the hood because if I went that way with the design, I would have had to put some sort of protection on the tip of the hook. Also, you can see the hooks protruding under the hood edge,  where as mine, you can’t, because it hooks on the hood latch rod mechanism on the inside back of the hood. The hook is small and deep so it should be very hard for the hood to ever be knocked free of it which is something we all think about when we have our hoods open. The Olds hood is huge, around 44-46” long I believe, plus it’s very flimsy in its early production years because it lacks a 1/2” angle bracing along the length of the hood doors later production year cars got. With the Olds, you cannot open both sides together either like you can do on other cars. Again, it’s such a big, fragile, and clumsy hood to open without hitting it on any other parts of the car, when it’s open, my main goal was to keep it positively secure. If you want a better idea of the design, I can make up some drawings and post them, just let me know.

Edited by chistech (see edit history)
  • Like 3

Share this post


Link to post
Share on other sites
12 hours ago, Gary W said:

Simply gorgeous.  

The quality and expertise of your restoration will set a new standard at Hershey.  

Truly a pleasure following your build.  Congratulations.  

 

Did you fabricate the hood prop?  I looks nice and sturdy.  I'd like to see your plan on that.

 

Not that you need it, but "GOOD LUCK" at Hershey!!!!  Stunning.

 

Gary

Ted, I agree with Gary W about the quality and detail that you painstakingly put into the '32. This will be my 48th. year attending Hershey, and I have seen some magnificently  restored cars over the years, and I believe that your Oldsmobile is up there with the best of them. Thanks. John

  • Like 2
  • Thanks 1

Share this post


Link to post
Share on other sites

Ted, well, you going to make it ??  sure hope so for your sake--see you on the show field Saturday--Tom

  • Like 1

Share this post


Link to post
Share on other sites

Hopefully I will make it. I have an issue right now I’m trying to remedy and if all goes well, I will. I will post more after I attempt to fix the issue.

  • Like 1

Share this post


Link to post
Share on other sites

Pinstripes were done yesterday. Really finished off the look of the car. Have the cowl vent door to repaint tomorrow because of a sanding/buffing problem. The pedal pad sample joe poured up from our mold should be here tomorrow from CO also so I can install that. 

EF0858C6-DB35-40FE-A1FF-25C9FD4D369F.jpeg

537A191F-5E19-4D7F-B757-5B715AE6FC74.jpeg

EAD78362-C770-408D-8965-6DC154238C3B.jpeg

EF04456A-F58A-4D5E-9BBD-7C211C77F4C0.jpeg

  • Like 7

Share this post


Link to post
Share on other sites

Few more pictures of the striping. Done by Brian Chairnay, very nice work.

2A19036B-B2F4-4A64-8EDB-22C7DECD662C.jpeg

BDFAB5DC-5A96-4FA4-B693-92C68FCF451E.jpeg

4AF380AF-B69F-42C3-8BFD-F6DBD0E305EE.jpeg

40F3F75E-3211-4684-A046-C50734F6F07C.jpeg

  • Like 6

Share this post


Link to post
Share on other sites

Here are a couple pictures of the molded pedal pad test sample. The back of the pad where the pedal stop flanges bump up against didn’t pour good on this sample but joe drilled 4 small holes around the perimeter of the recess to let the air out and the urethane to flow completely up into the recess. The two sample pads arriving tomorrow were made after the holes were drilled and came out correct.

9B2E67FC-E066-4007-9243-82E8FB8635D2.jpeg

27EF99A6-E0C2-4262-99D3-595078388A7D.jpeg

  • Like 2

Share this post


Link to post
Share on other sites
13 minutes ago, Laughing Coyote said:

Nice stripe work. Gives enough pop to break up the black and ties in nicely with the ww. 

I realize looking at the pictures that I didn’t get a pic of the striping on the lower body molding which runs from the front of the bottom inside edge of the ear fender all along the body and bottom edge of the hood up to the radiator shell. That stripe really shows off the nice curve of the lower body and how the front fender/running board top edge follows it. 

  • Like 1

Share this post


Link to post
Share on other sites
57 minutes ago, Laughing Coyote said:

Nice stripe work. Gives enough pop to break up the black and ties in nicely with the ww. 

Like Martin said, nice stripe work..... it's amazing how the pinstriping really sets off the body lines.... beautiful !

 

 

 

Steve

  • Like 1
  • Thanks 1

Share this post


Link to post
Share on other sites

Ted, Beautiful work . I love the fender spears. along with the pin striping  Superior work. Thanks, John

  • Like 1
  • Thanks 1

Share this post


Link to post
Share on other sites

Well the last part went on the car today. The two sample pours arrived and joe had them marked good and better. The tops came out great with the good one having two 3/8” air bubbles in the pedal stop area and the better one having two tiny bubbles in the same area. I figured I’d try installing the good one first in case of a screw up. Using an exacto knife, I cut right along the ribe side for each respective opening using a straight edge. This went fairly easy and it cut extremely clean. I installed it in place and found the tops of the pedal shafts would rub on the top of each opening. The original had angled holes but we didn’t have time to attempt this detail so we installed slightly undersized straight wall plugs. I figured if it was needed, I would just do my best with an exacto knife and trim the opening. Turns out, the formula of urethane that joe is using is very sandable and used the sanding drum on the Drexel to put the opening in. This worked as good as one could want and it is not worth the cost or the effort to change the plugs in the mold. We still have the top edge V groove to machine yet but we have already put provisions in the mold design for it. With the tops of the holes sanded at an angle, our recreation of the pedal pad worked out great and looks original. I’m very happy with the results. The center hole around the steering post is covered with a rubber pad and in my case, the original that came with the car.

F870EDCA-C4C9-499D-B759-9E5CC0AE1DA4.jpeg

54C53776-7474-4032-8C50-D9E2E1608F60.jpeg

A5A30F4F-A654-4CA9-8C32-7B9AAB529D58.jpeg

14C0A811-B256-4247-B601-42B79994D77E.jpeg

  • Like 4

Share this post


Link to post
Share on other sites

Couple more pictures with one showing the angle sanded on each pedal shaft opening upper edge.

2005C884-6F20-4F50-AE82-71C761345838.jpeg

832175C5-A618-4618-8928-5BAE739152BE.jpeg

  • Like 8

Share this post


Link to post
Share on other sites

Looks great Ted...... the little details stand out - the brake & clutch pedals, really neat !

 

 

Steve

  • Like 2
  • Thanks 1

Share this post


Link to post
Share on other sites
14 minutes ago, Mike "Hubbie" Stearns said:

I hope you take a much need break after Hersey is done, you deserve it after all your hard work

100% Agreed!!!  

  • Like 1
  • Thanks 1

Share this post


Link to post
Share on other sites

Ted, your pedal pad came out fantastic, your mold is very impressive. Would you want to make a mold for my Auburn throttle pedal?

See you in Hershey. George

  • Like 1
  • Thanks 1

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now