sebastienbuick Posted April 19, 2020 Author Share Posted April 19, 2020 having sanded, I ended up with a piece of Los Angeles in my trunk . Fortunately that I put not far from 10 tarpaulins in the trunk, calendar, ..., there will be less to clean Link to comment Share on other sites More sharing options...
sebastienbuick Posted April 19, 2020 Author Share Posted April 19, 2020 Then application of phosphate primer 2 Link to comment Share on other sites More sharing options...
sebastienbuick Posted April 19, 2020 Author Share Posted April 19, 2020 and some damage that will be repaired. The tip of the wing that was formerly repaired (like the other side that I had to redo) The bottom of the "frame" of the trunk Link to comment Share on other sites More sharing options...
sebastienbuick Posted April 19, 2020 Author Share Posted April 19, 2020 On the panel between the rear window and the boot Link to comment Share on other sites More sharing options...
sebastienbuick Posted April 19, 2020 Author Share Posted April 19, 2020 And the bottom of the wing It's really not much, I'll take care of doing it again later.Then apply white primer Link to comment Share on other sites More sharing options...
sebastienbuick Posted April 19, 2020 Author Share Posted April 19, 2020 Link to comment Share on other sites More sharing options...
sebastienbuick Posted April 19, 2020 Author Share Posted April 19, 2020 2 Link to comment Share on other sites More sharing options...
GARY F Posted April 19, 2020 Share Posted April 19, 2020 Looking real good 1 Link to comment Share on other sites More sharing options...
sebastienbuick Posted April 20, 2020 Author Share Posted April 20, 2020 8 hours ago, GARY F said: Looking real good Thank you very much GARY F ! Link to comment Share on other sites More sharing options...
sebastienbuick Posted April 20, 2020 Author Share Posted April 20, 2020 And here are two video clips I just found where there is a Buick Electra 69 Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 Hello everyone , here is the rest of the work with a view to start once the tarpaulins are removed To start with a little sheet metal on the bottom of the trunk frame Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 Cutting Substrate preparation And welding of the new piece Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 The continuation with another song Cutting Then welding of a new piece Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 The suite with the right side Cutting Formation of the new part Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 Then welding the upper part Cutting Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 New song formation Then welding 1 Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 The continuation with the tip of the wing, this part will be more complicated Once stripping a thick layer of putty, the result is not terrible Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 Cutout of the first part Then I see that the lining is in bad condition too, so cut the lining Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 Then formation of the new lining Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 Then welding of the new lining 2 Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 (edited) Then application of phosphate primer on the new lining and the other place redone Edited May 12, 2020 by sebastienbuick (see edit history) Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 Then after having the shape of the angle with a protractor, I can see what angle I should give to my new pièces Installation of the new parts and angle control Installation of the new parts, you can see that I made a mistake in my calculations and that I am missing a small triangle at the bottom left of this parts (this will be arranged later). I will refine the grinding and sanding of the welds better once the parts are completely finished Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 Then I continue by the left return from the tip of the wing Cutting Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 New parts formation Then welding Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 Then cut the bottom part Then formation of the new parts Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 Then welding Verification with the protractor Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 Then set up of this little triangle Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 Put in place the chrome strip to make a check It remains only to form and weld the two parts together and make the bottom of this parts verification with the protractor once the two parts are welded Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 Then the bottom and cut the lining Then formation of the new lining Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 Then welded Then I finish at the bottom, there will be more to grind all the welds Then application of phosphate primer Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 Then try with the chrome rod 3 Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 Then before applying the white primer, I will redo the sheet metal seal which is part during the sanding, around the trunk.I therefore equip myself with gloves, tape, and a seal cartridge with a gun Then I put the tape on all around Then I apply the seal Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 Then I do the same at these places Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 With her friend not far away who watches over her Then I protect and I can apply the white primer on the trunk, the repairs made and on the headlight strip that I had painted in dark gray after a while ago Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 And with the chrome strip 1 Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 1 Link to comment Share on other sites More sharing options...
sebastienbuick Posted May 11, 2020 Author Share Posted May 11, 2020 I then continued at the bottom of the rear wing, but I haven't finished yet, I will post the photos when this step is finished 2 Link to comment Share on other sites More sharing options...
GARY F Posted May 11, 2020 Share Posted May 11, 2020 Outstanding work and pictures. It is great following your work. 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now