Jump to content

Recommended Posts

2 hours ago, hursst said:

Thanks for the encouragement, but I have at least another 2 years.  All my parts need a LOT of work, nothing easy on this car.

 

 

Just keep making the steady progress.  That's all you can control.  Do that and it gets done and you get to drive it.  After driving it for 10 years it will seem like it took no time at all.

 

  • Like 1
Link to post
Share on other sites

Today I took the plunge and broke into my rocker panels.  Here's the passenger side before (Photo 1) and after (Photo 2).  Not having a proper spot weld remover, I just cut the metal as close as I could to the spot welded areas.  I will either buy a spot weld driller-outer, or maybe just grind the other pieces out.  Not sure yet.  Here's the driver's side after I cut the rocker out there (Photo 3).  The inner sills have rust holes, but it doesn't look too bad at first glance.  

 

My plan is to stop with the body, other than continuing to remove what's left of the paint, and wait until I can get it professionally blasted to bare metal.  I think at that point, I'll be able to see the full extend of the damage.  Right now, it looks like I could maybe put in some patch panels, as it looks fairly structurally sound, but the blasting may open up a whole can of worms.  I don't have the expertise to replace the full sill assembly myself, I would not be able to keep the body in alignment.  

 

While winter continues, I'm still working on some smalls on the side.  Was able to heat up the garage today and primer the rear number plate brackets and hardware.  Should be able to sand and paint them up tomorrow.  Picking up some chrome pieces later this week, and dropping more off.  I also need to call the engine shop.  It's been 4 months since I dropped it off and last I heard it was at the line bore shop.  Starting to get a little antsy, they should be wrapping it up about now.  Plenty of paint on the body still to strip.  I could get back into the heater, that would be easy and consistent work.  Probably shouldn't get too far ahead of myself, my credit card has been smoking other the last few months, it could probably use a break from car parts/services purchases.

100_5686.JPG

100_5687.JPG

100_5694.JPG

  • Like 1
Link to post
Share on other sites

Chris,  The number plate is yours, please email me, jrdshen@verizon.net.  Same place where you got the 2 wheels.
Your message to me via AACA had a no return email address.  It's the second time I've not been able to reply to a message sent via the club.  Clicking on "Hurrst" for personal info also gave no option to send a PM back either.   Can't understand what's going on.   Dave

Link to post
Share on other sites

Thanks Jeff, it is getting done, a little at a time.  There are some rust holes on both sides at the back of the trunk sides.  There is also a lot of damage at the very upper trunk where it meets the bulkhead.  Battery acid/gas got to it.  I should be able to patch these areas up okay without having to do major surgery.  All 4 fenders will need some patch panels at the lowers, but that should be it.  No major structural rust anywhere, but quite a few minor rust outs that need attention.  It will be a busy summer welding and priming.

Link to post
Share on other sites

Nice weather today, so thought I'd attack my heater box, as I thought it would be easy.  I was right, it's a very easy heater.  Here it is before I started (Photo 1).  Came apart very easily.  I blew it up and started blasting the larger parts (Photo 2).  Minor rust throughout, but nothing the clogmaster 2000 couldn't take care of.  I completed blasting the major parts and got a coat of primer on them (Photo 3).  Most of the hardware needs cleaned up and zinc plated.  I'll need some rubber bushings, new "Smiths" tags (the old ones are corroded and probably not nice enough to reuse), and I'll need to get the heater core and blower motor tested.  The heater core looks to be in excellent condition, surprisingly.  The motor looks very good, too, just needs some cosmetic cleanup.

 

I'm going to have to re-blast my rear number plate brackets, as the pitting is too deep for just high-build primer.  Will have to use some body filler.  No huge deal.  Now that the body and body panels are on hold until consistent nice weather, I can continue to work on ancillary pieces in the meantime.  I may go for the steering column next.

100_5707.JPG

100_5710.JPG

100_5712.JPG

  • Like 4
Link to post
Share on other sites
  • 2 weeks later...

Been a couple weeks, but made some time this weekend.  I got back more parts from the chrome plater, so I was able to finish my parking brake assembly (Photo 1) and get it installed on the trans tunnel.  MUCH easier when the tunnel is not installed.

 

Also still working on the heater (Photo 2).  Had the heater core tested and it's perfect, for some reason, so had it thoroughly cleaned and back in it goes.  Took the blower motor to a electric shop to get tested and maybe rebuilt.  Took my repro ID tag to an engraver shop to see if they can repro the original stamping.  I'm going to reuse the original CAUTION tag, even though it's a little ratty.  The repro one I bought is wrong in so many ways and the CAUTION lettering is in red instead of the proper black.  It takes just as much effort to do these tags right that it does to screw them up, yet they screw them up every time.  Got the heater box painted, but may still do a little touch up.  The lacquer spray paint I used shows even fine sanding lines, so may need some redoing.  I had to strip off much of he primer and apply body filler earlier in the job, as my first attempt ended up with too much pitting.  I'm waiting on some additional grommets before I can put the whole thing back together.

 

Still slowly working on the bumper and numbers plate assemblies, but these pieces are all rusted and damaged, so having to supplement a lot of it with new parts.  

100_5721.JPG

100_5725.JPG

  • Like 2
Link to post
Share on other sites
22 minutes ago, hursst said:

It takes just as much effort to do these tags right that it does to screw them up, yet they screw them up every time. 

 

 

 

I've always wondered about that.   I wondered a little that it might be a copyright/trademark issue but I think that's a little unlikely.   

 

Glad you found something that worked... that always helps progress.   Looking good!!

 

 

Link to post
Share on other sites

Got about 3" of snow today, which in Northern Virginia is a national emergency.  Most cowardly, untrained drivers in the world, so the gov't made me stay home today.  The good news was, I headed out to the garage.  

 

The heater work is on hold while I wait for parts, so today, I jumped into the rest of the steering column (Photo 1).  Steering column assembly is a mess.  The shaft itself is excellent, but the steering wheel is completely destroyed (I already bought a new one), and the optional adjustable steering column is corroded.  I was able to take the whole thing apart, eventually, but the separate adjustable shaft would not come out.  It looked warped or bent.  I ended up applying a lot of heat and some tactful hammer blows, and eventually it came out.  I soon discovered the issue.  Some cretin previous owner decided to try to take this thing apart, but they must have been severely mentally challenged, as they decided to try to unscrew the shaft, which 1) has spline in it and 2) has a metal key in it, to keep it from being pulled completely out.  So, they tried unscrewing it and somehow bent the whole thing (Photo 2).  Note that the keyway is bent to the left.  Idiots.  So, I have to buy a whole new shaft, which is $164 + tax from Moss.  Inside the shaft was a vintage Beech Nut gum wrapper from the 1960's (Photo 3).  Evidently this simpleton could not remove the adjustable steering shaft and chew gum at the same time.

 

Moss will be pleased with my next parts order.  My bank account will not be.

100_5727.JPG

100_5731.JPG

100_5732.JPG

  • Like 1
Link to post
Share on other sites
  • 2 weeks later...

Never been busier in my life.  Too many projects, not enough time! 

 

I've been trying to wrap up a lot of small projects on the car while I wait to get more into the body repairs.  I refinished the steering column (Photo 1) with new felt bushings and new telescoping upper shaft to replace the one that someone pretzeled.  Was not able to complete the rest of the upper telescoping pieces as they need to be re-chromed, so that will be about 2-3 more months.  Also working on the rear license plate bracket assembly.  Heavy pitting has held me back, as I thought I could fill the pits in with sand-able primer, but the pits were too deep, so I had to use some body filler (which I should have done to begin with, lesson learned), then had to do some wet sanding at the end.  I ended up switching paints and the original gloss black I used was too fine, revealing every detail.  I got some better paint that did a much better job of hiding fine scratches.  After redoing everything about 3 times, I'm just about there.  The rear license plate lamp assembly cover will have to be re-plated, so that will be a while until it's finished as well.  I took the base and rewired it (Photo 2), so now I can rebuild the whole assembly, minus the glass and cover.

 

Still working on the heater, but waiting on an ID plate engraver and the blower motor tester.  Have a few smalls left to redo, but it should be complete in about 3-4 weeks.

 

I'm also working on the rear bumper bracketry at the same time, pretty much finished with that, now starting the front.  Fairly easy stuff. 

 

I really need to get to a good stopping point, as I'm ready to detach the inner rockers.  I tried an air chisel to try to break the spot welds, but that didn't work as the chisel point is too thick and just warps the metal.  Of course the air chisel itself failed after only 10 minutes of use (yes, I oiled it beforehand).  It will be going back for a refund tomorrow.  I then purchased an Eastwood spotweld cutter air gun, which should get the top and bottom spot welds easily. It's in the mail now.   I think I will have to manually drill out every spot weld that holds the inner rocker panel to the door pillars and other places on the top sides, as I see no other way to do it without doing some heavy damage.  My door pillars are somehow solid, so I need to save those and the flanges that come off of them at the bottom.  This will be the hardest part of the car, but ready to get it done before the good weather starts and I get the rest of the body sandblasted and in primer to seal it before I start the real body work.

100_5745.JPG

100_5748.JPG

  • Like 4
Link to post
Share on other sites
  • 2 weeks later...

Back from some travels and a lot of work hours locally.  Was finally able to finish the rear numbers plate assembly.  Turned out well overall.  Still some minor pitting, but you can't see it when it's on the car, so good enough (Photo 1).  I have the chrome frame for the light headed to the chromer.  Re-wired the light as the old wires were disintegrated.

 

Otherwise, I'm finishing up on the heater box.  Taking a long time, as I still have the blower motor out at a shop, which seems to have been closed for quite a few days now, so not sure what's going on there.  Not out of business, just closed up.  I'll have to investigate further.  I got a repro "Smiths" ID plate, but it's pretty crappy.  I was not pleased with it.  I found a company in the UK that makes repros that are very close, so I ordered one of those and it's at an engraver now to get the numbers on it.  The rest of the parts are in primer and will be painted tomorrow.  Should have the whole thing done in a week or so, minus the missing blower motor.

 

Tomorrow, I'm going to continue trying to remove spotwelds from the inner rocker.  Just bought a spot weld remover gun/drill from Eastwood, so we'll see how it works.  Won't help on the thin tabs that come down from the door pillars and the attachments at front and rear of the rocker, but it should make short work of the upper and lower portions, where you can get the C-clamp portion of the drill assembly around the pinched areas.

100_5773.JPG

  • Like 2
Link to post
Share on other sites

Very productive weekend; hard to find nowadays.  I finished painting the rest of the heater parts (Photo 1).  Will assemble the heater, minus the blower motor as soon as I get the "Smiths" ID tag back from the engraver.  I also completed the front bumper brackets.  I'll put them on the car as a good storage location for now.  

 

Big milestone today, was able to remove about 65% of the passenger side inner rocker panel.  The Eastwood spot weld remover works very well, I'd highly recommend it.  Once you get the hang of it and set the depth of how deep you want to drill, it's a piece of cake.  This has already paid for itself.  That being said,  it's of minimal use in tight corners.  Here's what it did for the top portion (Photo 2).  And here's where I am currently (Photo 3).  There are still pieces attached under the door pillar that will require some more work, as I want to save the door pillar, as it's solid.  I will probably do some damage I don't want to do, but there isn't an easy way to get some of the flaps from the door pillars to the inner rocker easily.  I was also not able to do the section at the front door pillar and in front of it, as the car is supported up in the air under that section, so I'll have to make some adjustments so I can reach it when I get back to the job.  I now need to buy some new inner rockers from Moss to see how everything lines up.  The inner support panel is rough, but it looks salvageable.  I'll have to weld in a few patch panels at the bottom to make it look nice and have solid metal to spot weld on the rockers and attack the trim piece after the car is painted.

 

I will probably wait until I get the repro panels so I can compare what I currently have to the new rockers while the driver's side original rocker is still installed and take some measurements, then I'll probably wait to get the whole body blasted to get rid of the surface rust before I install the inner rockers.  I think once I get the body blasted, I'll officially be on the downhill portion of the restoration.  I'll be 3 years in in May.  A guy in my local MG club called me "anal retentive" as I am taking so long to do this resto and I'm a stickler for originality or at least accuracy.  Most of the club owners drivers, not show cars, which is great, as these cars should be driven.   This just motivates me more, as I'm going to shoot for the best MGA out there and hopefully win some AACA awards with it.  Don't worry, I'll be driving it, too, it won't be a trailer queen.  If it doesn't win anything, I don't care either, I'll still have a great MGA to enjoy that I built with sweat equity.

 

Happy St. Patrick's Day!!!

100_5786.JPG

100_5780.JPG

100_5787.JPG

  • Like 3
Link to post
Share on other sites

Got a lot completed this weekend.  Finally finished the heater (still missing one ID tag on top, though) (Photo 1).  Turned out well.  Compare to the "before" photo on my Feb 3rd post.

 

Ok, I have most of the small stuff I was working on completed, so now focusing only on the body, now that the warm weather it just about here.  I re-assessed my inner rocker panels again.  I think the large panel that is left is called a "castle panel" or something, but it's the only thing left preventing the car from being cut in half.  It looks like the upper 3/4 of the panel is in good shape, just has a lot of surface rust, but the lower 1/4 on both sides is a disaster.  So, I decided to save the top part, but cut off the bottom 1/4 of the entire panel (Photo 2).  I still have a section of the inner rocker I need to move at front, but I was able to work on the back part for now.  I first cut out the rear panel (there are actually 3 panels lapped and spot-welder together) and replaced it with fresh metal (Photo 3).  The section where the line is at right is actually depressed by about a 1/16" so that the main panel can go over top of it.  Turned out okay, but I'll have to be very careful about lining up the holes at the bottom for the long trim piece that goes along the bottom to cover up all the spot welds.

 

I next cut out the same portion for the the entire middle piece, which goes up to the front door pillar.  This piece is also lapped and spot welded with the front piece.    So far so good.  I'm going to hit Moss Motors in about 2 weeks to buy repro inner rockers to complete the repair.  Going to do one side at a time, so I can keep the other side intact for reference.

100_5796.JPG

100_5790.JPG

100_5793.JPG

  • Like 1
Link to post
Share on other sites
  • 2 weeks later...

It's getting harder and harder to find any time to work on the MGA, but I found some time today.  Having tons of long-term issues with my other cars, like a power steering system in my old Camaro that can never be repaired no matter how much effort, money, time I throw at it over a 6-year period.  People not knowing the correct bearing to use in my Plymouth water pump (has been rebuilt 4 times, yes, 4 times).  People "correcting" old parts without asking me (converting an adjustable generator to non-adjustable, which, of course, needs an adjustment), a parasitic drain on the battery of another car that no one can find through 3 shops and 5 years of effort.  I could have retired years ago if I never got involved with cars.  

 

Ok, for the MGA, I continued on the rockers.  I went to Moss Motors and got repro inner rockers and vertical rocker supports.  Here's the whole panel mocked up (Photo 1), but I found the top of the original panel to be okay, plus if I removed this panel, there'd be nothing between the front and back of the body and I don't want to have to get involved with jigs and flexed bodies, if I can help it.  I spent half the day cutting out the rest of the bad metal around the door pillars, which was incredibly difficult do to without destroying everything  I did some minor damage, but I should be able to make it look fairly nice and no one will see it anyway.  As long as it's structurally sound.  Here's the cut-out piece sized in (Photo 2).  Here it is about half-way welded in.  My welding is still not very good, plus it's tough to weld onto the formerly rusty and probably thinner original panels.  Lots of burn-through and some warping, but I think I got it on there fairly nicely in the end (Photo 4).  It will need a LOT of grinding, probably some pin-hole touch-ups and more grinding on the other side.  Then, some hammer and dolly work to get the warping straightened up.  

 

The next job will be the front section (these panels are composed of three separate panels that overlap).  The front part is more solid, so I will only have to cut out maybe the bottom 1 1/2" to get to good metal.  Once that's done, I can weld in the boxed inner rocker panel as one unit.  That can be all spot welded.  I have a friend who has a home-spot welder, but I think it takes a special voltage or plug, which I may not have.  Plus, for most of the panel, you can't get behind.  Eastwood makes a spotweld adapter for my welder.  You have to drill a hole in the first panel, then you can make the connection with the welder adapter that should be somewhat clean, so I will probably buy that for the main rocker and the outer rocker.  Once I get the passenger side done, I'll move on the the driver's side, which I can use now as a reference.

 

In the meantime, I just hit over 6 months of my engine being out at the machine shop.  I check in every two months and it's always "it's at the machine shop, they just finished this and just did that, should be ready soon.  I think 6 months is too long.  They originally said it would be ready around Feb 1st, when I first dropped it off.  Time for another visit, but this time, we're going to have to establish some deadlines, I'm getting a little fed up.  Also, I've had a better heater ID tag at the engraver and it's been there for about 3 weeks now. How this takes more than about 3 days is beyond me.   I never get any updates from any of these shops, the burden always falls on me to call them, they rarely or never call me.  Hmmm, really frustrating last few months with car repairs and repairing.

100_5806.JPG

100_5807.JPG

100_5808.JPG

100_5809.JPG

  • Like 1
Link to post
Share on other sites

It does seem like no one is as interested in your stuff as you are... and you have to call and call to find out if anything is going on.  After a while you begin to deduce that lies have been told because you know things don't take that long and even if they did, then they'd need to be billing you for that and you're not getting 6 months of billed time from the machine shop (at least, you better not!!!).  This was the primary motivator for me to try and do everything... and I think you've said a reason that you've done many times more on this restoration as well.  I'm sorry it isn't working out for you but you'll do more and more and it should go smoother and smoother.   Don't even get me started on the mechanics that can't find problems... you stand a better chance of educating yourself and fixing just about any mechanical issue with a car these days as you do finding someone that can fix something without a computer telling them how.

  • Like 3
Link to post
Share on other sites

Well, yet another setback.  I called the British car shop today about my engine.  It has been there for over six months.  I was greeted with "good, you got my message!"  I never got a message.  Supposedly I was called on Friday.  Good timing, but never got the message.  Anyway, long story short, my engine was farmed out to a machine shop (which is fine) for line-boring, cylinder boring, honing, magnaflux, or any other service the block needed.  The block was finished about 2 weeks ago, returned to the British car shop, who then discovered a crack at the rear of the block near the oil journal, or something like that.  The shop was very upset with the machine shop, as they should have caught this.  To repair the crack requires another specialist and will be about a 6-8 month wait, plus only a 50% chance of success and an 80% chance the crack will come back in the future.  The British car shop located another block that may fit the bill.  Luckily, my engine tag can be moved to another engine, as nothing is stamped in the block, so I'm not too upset.  Anyway, they need to now check out the "new" engine to see what it needs.  I'm supposedly at the top of the list, due to it being their error that they didn't catch it earlier, so the British shop is estimating 1 month more, if everything checks out okay, which means 3 months to me.  

 

I do think the British car shop is doing fairly well for me, although they are not keeping up with communication.  I don't know the exact issue with my old block and if the crack was simply missed during the magnaflux process, or it developed over the last 6 months, so I can't really get upset, just frustrated and disappointed.  I really wanted to get the engine in the car before spring, now it's looking like mid-summer at best.

 

At least I got in some more grinding on the welding after work.  I'm going to have to find a coarser grinding disk, it is taking forever.

  • Like 1
Link to post
Share on other sites

There have been some very good reports on other threads about stitching cracks. Matt Harwood's Lincoln K engine was just treated. It is a permanent fix if done skillfully, according to the posters.

  • Like 2
Link to post
Share on other sites

Hi,

My reports on the rebuild of my MGBV8, for the MG Car Club V8 Register, may help you with your welding and plug welding (spot welding with a MIG). There are a lot of reports but I did a index at the end to make finding things easier.

http://www.v8register.net/profileV8RebuildMacartney.htm

I have been following your posts with interest.

Mike

Link to post
Share on other sites

Left work early (or late, considering I had extra hours for the week) and did some more fREAL work on the MGA.  It's getting easier as I go since I'm learning along the way.  Today I bought some better grinding wheels and spent time grinding most of the welding on the rocker support mostly flat.  Opened up a lot of holes in some sections where my welding was not the best, but overall, not too bad, most of it turned out satisfactory.  Started on the front section by cutting out the bad portion (Photo 1).  The front was better protected, so didn't have to cut quite as high.  Good at that, as there is a support bracket welded toward the front on the other side, so I didn't have to mess with that.

 

The only sheet steel I can find is 24" long, and of course, I need about 26", so had to leave a gap which I'll fill later (Photo 2).  So far, treated the overlapping metal at the left end with weld-thru primer, as it overlaps the center piece, and cleaned up the rust where I'll be welding.  Right now, just held in there by a large magnet to get it set up.  Will probably weld it tomorrow.

 

After that, I'll weld in the gap, then grind it, then double back and weld up the holes that are left over from the bad welding from before, then grind it again.  I'll throw a good dose of weld-thru primer over the whole thing, then do a little hammer and dolly on the bottoms of the door pillars, as I had to fight with them to get out the rusted inner rocker.  After that, I'll prep the repro inner rocker.  Not sure how I'm going to spot weld it yet.  My friend never got back to me about how his home spot welder plugs in, so I'll probably just use the Eastwood spot weld adapter, which will unfortunately involve me drilling dozens of holes in the inner rocker in which to put the "spot welds."  Pleased with my progress since I've never done this before.

100_5810.JPG

100_5811.JPG

Link to post
Share on other sites

"Eastwood spot weld adapter, which will unfortunately involve me drilling dozens of holes in the inner rocker in which to put the spot welds." 

 

You can just weld into the holes using the standard torch without the adapter.

 

2075355728_023702-06-2016.thumb.JPG.f9cf37f00abd396ffa673e35f87bb28a.JPG

 

No need to drill all the holes you can use a hand or air punch to cut the 1/4" holes.

 

482379144_026705-06-2016.thumb.JPG.c62093fe18add501f2b3fdd8c6be9ecc.JPG

 

These pins are ideal for holding parts together for welding. I hope the above helps you.

Link to post
Share on other sites

Mike,

    You are right, but I'm not that good.  I'm going to try the adapter, it's not that pricey.  It sets up the right distance and makes everything vertical and uniform, so I'll try it out.  Those pins are a good idea, I may pick some of those up soon.  Right now, I have really easy surfaces to work with, so clamps and magnets work fairly well for now. 

 

    Thanks again for the tips, they are all very helpful and will improve my work and speed up the process.

  • Like 1
Link to post
Share on other sites

I don't know if you have come across these types of wire brush that are encapsulated in pressure moulded epoxy resin, this type of wire brush never clogs and will outlast conventional brushes. I bought one from Frost, in the UK, it was used on the MGB and Humberette restorations and still has useful life left in it. I use it in a reversible drill, when it doesn't work so well one way I reverse the drills rotation.

1391.png.9d06a077f35eceddc2f1380be3b7822f.png

Frosts encapsulated wire brush.

1392.thumb.jpg.041eafb142139c7bf9511f14fafdd7e1.jpg

This is another type I found on Amazon.

They seem expensive but they do last a very long time.

Regarding the spot weld adapter. I did try using one when I first had a MIG welder and found that I got better results without the adaptor.

Another tip - when starting to get used to MIG welding, make sure the metal you are welding is clean and free from rust, hence my suggestion on the above types of wire brush.

 

Link to post
Share on other sites

Mike, another great suggestion.  I've never heard of these before.  I blow thru wire wheels quite quickly, so I will definitely look into this.  I'm having much better luck with certain parts of the welding then with others, as some of metal is a little pitted and I'm sure I'm hitting some small spots that aren't as clean as I think.  Thanks again.

 

 

  • Like 1
Link to post
Share on other sites

Quick update, yesterday I finished welding all the patch panels to the bottom of the inner rocker vertical support (Photo 1).  The welding was very challenging for an amateur like myself.  The middle section had much more surface rust on the upper portion than did the front section.  I had a lot of burn thru where the metal was thinner on the upper half, so it was a battle to keep the heat low enough not to destroy all the metal, while keeping it hot enough to make a connection between panels.  Lots and lots of grinding, plugging pin holes, repeat.  The front section was relatively easy and I got better welds and minimal pin holes.  A sloppy job, indeed, but no one will see it.  I'll be cleaning up the inner side of the work more, as that needs to fit fairly flush against the frame rails of he chassis.

 

Today, I should be starting on grinding out what's left of the spot weld fragments on the panel, repairing a couple holes I made in the panel whilst chiseling, repairing a rust-out hole on one of the door pillar bases, and maybe getting time to wire wheel and metal treat the middle and weld-thru prime the portions where the inner rocker will be spot welded.  

100_5813.JPG

  • Like 3
Link to post
Share on other sites

It looks good and straight. Well done. The main 'trap for young players' in sill work is welding a slight sag into the structure which plays havoc with the door shut lines. It is very easy to get wrong, and difficult to rectify. I am constantly trial fitting the panels and door at that stage.

  • Like 2
Link to post
Share on other sites

"I am constantly trial fitting the panels and door at that stage."

 

Excellent advice. From my memory of replacing sills on an MGA, in the early 1980's, this was one of the hardest sill replacement jobs I had ever done.

Link to post
Share on other sites

I got my Eastwood spot weld adapter on Friday and was able to use it today. I was very pleased with it.  It said in the instructions that for my particular welder, I do not need to drill holes in one of the panels, which will save me hours of time.  I used the adapter kit to spot weld the two overlapping sections on the vertical rocker support panel and it worked quite well.  It took me a few tries to get the settings right, but by the second section, I was getting fairly consistent welds and full penetration.  Nothing nearly as nice as the factory, but again, no one will see these particular welds (Photo 1).  With a few minor adjustments, I should get some nice welds for the actual rocker panel, although right now, the welds are too wide.  Speaking of the rocker, I was able to remove the factory primer on the inner tabs and spray them with weld-thru primer, in preparation for welding them on.  Hopefully next weekend I can get the repro inner rocker fitted, if not actually welded on.  

 

As a side project, I started on the goal-post upper panel.  This is where the tops of the floor boards and the trans tunnel attach, then the panel itself bolts onto the main goal post (Photo 2).  I also started on the defroster tubes and vents that come out of the heater.  Here's the newly-painted versions of the vents and panel (Photo 3).  I'm zinc-plating the hardware and will be applying new damper felt.

 

My engraver keeps saying "I have other work, but give me 24 hours" for my Smiths heater tag.  He's given me this line 3 times now, still hasn't done the engraving after over a month.  I'll be picking it up tomorrow and taking my business elsewhere. 

 

No word on my engine, either.  I should hear something any time now, but I don't expect to hear anything unless I contact them.  I get a feeling from many shops that I deal with in general that customers are a burden and a low priority.  They have so many customers that it doesn't matter to them if they take their business elsewhere, there will always be another customer.  It's always up to me to contact these businesses to try to figure out when they will have things finished, they never contact me and they never come close to meeting their deadlines.  This is becoming quite a long restoration with many delays.  Glad to see the progress on everyone else's cars.

100_5833.JPG

100_5818.JPG

100_5832.JPG

  • Like 3
Link to post
Share on other sites

Only had to work 10 hours today, so took an hour to mess around in the garage.  Have to make the time.  Was able to rough-test fit the inner rocker panel today (Photo 1).  Seems like a reasonable fit so far, but still needs some minor adjustments.  The door pillar bottoms will need some more attention, they are a little bent up now from the work I had to to remove the original rockers (maybe the bottom 1/2", so not too bad).  Overall, pretty pleased.  I figure if I can do the inner and outer rockers myself I'll save a good $5k-$6k with the insane rates they charge nowadays.  Just hoping I get it right.  Will use the other side to measure everything and make sure it's as close as possible before I commit to welding anything.  I'll have to tack on the outer rocker and throw the doors back on, I suspect the repro outer rocker may need some adjustment for proper fit.

 

I fired the engraver yesterday.  No apology or anything, he just gave me my heater tag and I left.  I'm sorry I was a burden to him by trying to give him money to do him to do 15 minutes worth of work.  I found another guy up the street, so we'll see how he does.  He says 7 business days.

100_5837.JPG

  • Like 2
Link to post
Share on other sites
On 4/21/2019 at 7:05 PM, hursst said:

I get a feeling from many shops that I deal with in general that customers are a burden and a low priority.  They have so many customers that it doesn't matter to them if they take their business elsewhere, there will always be another customer.

 

 

Entirely aside from the cost factor, this is the major reason I determined that I had to be able to do almost everything myself. I simply would not have the patience to put up with the frustrations you're having added to the uncertainty of whether the job will even be acceptable.

  • Like 4
Link to post
Share on other sites

Been working 10-11 hour days (not on the MG, just regular boring job), even had to work two hours on Easter to catch up.  Really tired of it.  Only had to work 9 hours today so forced my way out to the garage to get most of the spot welding done on the inner rocker (Photo 1).  I completed 95% of it, roughly replicating where the factory spot welds were (Photo 2).  Had a few instances where I burned right thru both layers of metal and a few that didn't quite go thru both, so will have to do some grinding, filling, and double checking, but overall, still pleased with the spot weld adapter tool.  I made a small mistake, I should have shored up the attachment points under the door pillars first, but kind of forgot about it, so there needs to be some adjustments under the front pillar.  May have to cut a little and weld in a few small pieces to make it right.  A rookie mistake, but it's not a huge concern since none of this will be seen and it doesn't affect placement of any of the outer panels, so if it's a little sloppy, so be it.  I also test-fitted the outer rocker (Photo 3).  Actually seems to fit quite well for an aftermarket part.

 

I still have to spot weld the two far-end tabs on the inner rocker, then clean all the welds up a little, then tackle the door pillar attachments.  The more I think about it, I will probably cut out all the tabs at the bottom of both pillars and weld in new tabs, as what's left is quite bent up and rusty, plus I'll be able to fill in the gap I made under the front pillar.  Tired of getting so behind on the project, it's been almost 3 years.  I think I'll feel caught up when I can get the rockers finished, get the body blasted, and get it in etching primer so I can do the rest of the bodywork.

 

As a side project, I finished the firewall metal piece that attaches above the floorboards and below the goalpost.  Was able to restore all the parts and hardware, just added new felt gaskets (Photo 4).  Missing the rubber grommet for the steering column, but will get or make one soon..

 

Got an update on the engine, the new block seemed to have checked out quite well, but it will need to be bored .060 over.  The shop says the engine should be back from the machine shop in one month, which really means two months.  At that point, we can put all the ancillary parts on and get it on a test stand.  If that works out, it will end up being about a year.  If everything works out right, I can throw the engine on the chassis, then move the body towards the front of the garage and put the chassis in the back on the garage until it's ready for the body, giving me more room to work and easy access to moving the body from the garage.

100_5852.JPG

100_5853.JPG

100_5854.JPG

100_5855.JPG

Edited by hursst (see edit history)
  • Like 3
Link to post
Share on other sites

You seem to be getting the hang of this spot welding with the MIG welder. How do you get on with the weld thru primer. I have never managed to get on well with it. What make are you using? It's starting to look more like an bodyshell again. Keep up the good work.

Link to post
Share on other sites

Mike,

   Thanks for the encouragement. I hope to get some more productive days in over the next 2 weeks. 

 

    I haven't have any issues with the weld-thru primer, it seems to do its job.  I use the Eastwood brand.

 

  • Like 1
Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...