rapidride2 Posted October 4, 2012 Share Posted October 4, 2012 (edited) Hello, I have found a 52' Buick road master with a power steering set up. However it is a thousand + miles away. I am wanting to get this rare setup. however I need details on everything i should get. I'm assuming i need to get the crank pulley on the harmonic balancer, brackets pump. reservoir, lines etc. How does this dismantle from the steering column? Can I use my original manual steering column and bolt the power steering unit to mine? Does it unbolt from the steering tube? Anything else i need like a pitman arm etc????Also, will my gear selector linkage mechanisms on my non-power steering car work with this unit or do i need the set up from the power steering car (i hope not)Is a column (steering shaft) the same on a power steering car versus non-power steering car? (i really hope not)I am 38 so I don't know too much about this setup.. i just know it's rare and would be a great addition to my 52 riviera road master. Any help would be greatly appreciated. Edited October 4, 2012 by rapidride2 (see edit history) Link to comment Share on other sites More sharing options...
Erik Posted October 4, 2012 Share Posted October 4, 2012 (edited) You will need the complete steering-column and house as well. Also the gear-linkage to the dynaflow.I made the change a few tears ago and it was not all that difficult. The hardest part was replacing the steering-column and boxes as a unit. The power-steeringbox is built on top of the existing steeringbox.And you will love it when done Edited October 4, 2012 by Erik (see edit history) Link to comment Share on other sites More sharing options...
PONTIAC1953 Posted October 4, 2012 Share Posted October 4, 2012 you will need the complete built together steering coluum-power steering unit, it doesn't have a connection ragjoint that started being used in 56 or 57. the lower pullies perhaps the harmonic balancer, the pullies on the waterpump, the pitman arm, the trans linkage, the pump and it's mounting bracket, hardware, the hoses. charles coker, 1953 pontiac tech advisor. Link to comment Share on other sites More sharing options...
Guest martylum Posted October 4, 2012 Share Posted October 4, 2012 Hi-I'm in the middle of restoring 53 Buick 76X convertible and have removed the P/S components. You want to get everything you've listed including the whole steering column right up to the steering wheel and perhaps even the steering wheel to be sure you'll have everything needed. You also want to get the 2 mounting brackets and bolts which hold the box to the frame rail as they too might be different as well as the pittman arm.I have my pump and box at a hydraulic testing shop for testing as the car has lots of miles on it and I only want to install it once. If the box and pump don't have oil in them be more nervous about their condition. The box is quite heavy 70-80# and won't be cheap to ship.I installed a P/S setup on a 56 Buick from a 56 parts car-my how they cut the weight and simplified things in three years.Martin Lum53 Buick Link to comment Share on other sites More sharing options...
rapidride2 Posted October 4, 2012 Author Share Posted October 4, 2012 You will need the complete steering-column and house as well. Also the gear-linkage to the dynaflow.I made the change a few tears ago and it was not all that difficult. The hardest part was replacing the steering-column and boxes as a unit. The power-steeringbox is built on top of the existing steeringbox.And you will love it when doneDid you need the harmonic balancer, water pump pulley for the swap? I am assuming i could use my current steering wheel. i wonder if i could use my existing steering center link? Link to comment Share on other sites More sharing options...
MrEarl Posted October 4, 2012 Share Posted October 4, 2012 you may find this article helpfulSwapping from Manual to Power Steering 1 Link to comment Share on other sites More sharing options...
Erik Posted October 13, 2012 Share Posted October 13, 2012 Did you need the harmonic balancer, water pump pulley for the swap? I am assuming i could use my current steering wheel. i wonder if i could use my existing steering center link?Yes, the harmonic balancer for PS has two grooves. One for fan/waterpump and one for PS pump.The '52 setup was the original steering box with the PS built on top. From the pitman arm and out everything's the same, but as the steering shaft was shortend to accommodate for the PS, the whole column, gear linkage, brackets and bolts are different. Wheel, signal arm/mechanism, horn etc are the same.The short version for the swap is: Detatch pitman arm, gear linkage and steering colomn brackets etc. Swap steering colomns. Replace harmonic balancer. Mount PS pump. And now the tricky bit: Drain some cooling fluid and remove 2nd and 3rd left hand headbolt and fit the resevoir. You might consider replacing the head gasket while you are at it. Thighten ALL headbolts to spec. If you don't have a fancy tool you will need to remove the rocker assembly and from here to a new headgasket is ½ hour. Do the plumbing and bleed the pump according to the shop manual and Bob's your uncle. Link to comment Share on other sites More sharing options...
Guest honestb Posted May 19, 2016 Share Posted May 19, 2016 (edited) Hi have 52 Buick 50 Series Super Woodie Wagon .Want original manual steering set up for it.Steering wheel to steering box mounts and all. If you have one and are willing to sell.Or know where I can locate it please email me at belvinbryan@sbcglobal.net. Thanks Brian Edited May 19, 2016 by honestb add pic (see edit history) Link to comment Share on other sites More sharing options...
Guest Posted May 20, 2016 Share Posted May 20, 2016 (edited) Greetings Posted pix of this swap in process on my friends 50 Super convertible in the modified forum. No manual trans for Roadmaster 1952 that I've heard. The steering column is different even between automatic cars as it had to be shorter between the steering sector and the firewall becuz the power steering box is huge compared to manual. Interchange says PS sector, "common" 52-55, but steering shaft being intregal from box to wheel, with different lengths every model, makes interchange a cut and weld situation most times if not same model. Of course I could sell you a floor shifter, oops, never mind this is the "stocker" forum, all puns intended! The pulley on the balancer is riveted on from the factory, makes it intergal to the balancer small or large engine, the brackets from small engine aren't the same as those for the 320" Roadmaster engine.The "kit" we found is for the small engine cars, so the PS fluid resevoir is attached on top of the pump. The setup I have for 320 has a remote resevoir that mounts to the cylinder head bolts. The 320 pump uses a cast manifold bolted to the top of the pump for the extra hoses that come from the remote reservoir, used, I think, becuz the air cleaner was in the way of the reservoir that would otherwise be attached directly on top of pump on the small engine application. It interchanged bolt for bolt on the 50 Super. Rebuilt pump and sector done by Lares mfg. 800.00 and change, new hoses made by Pirtek Co. 151.00. Can't imagine what cross country shipping would cost$$$$$. Word of caution, if it's a long way away be certain you have absolutely everything you need in one shot, cuz those individual parts are pretty much unobtainium. I'd like to have a 320 pump bracket myself, anyone? Hope that helps. My experience, others may differ. Greg PS Whiteys' kid and his crew did a beautiful job restoring those parts(Lares that is)! Edited May 20, 2016 by Guest Dim bulb! (see edit history) Link to comment Share on other sites More sharing options...
Pilgrim65 Posted June 30, 2016 Share Posted June 30, 2016 Hi guys reading this with interest , have 53 special , but not driven it yet as waiting for delivery. it has no power steering , wondered if this will be difficult and how much of a job changing it would be . Obviously availability and cost of parts also major consideration . Any views welcome cheers pilgrim Link to comment Share on other sites More sharing options...
JohnD1956 Posted July 1, 2016 Share Posted July 1, 2016 Pilgrim, it is understandable that most folks want power steering today. Every vehicle made in recent years has it and if you've ever had to turn the wheel of a car where it did not work, you know it's very difficult. But standard steering in the 50's was not like that. Standard steering is not that hard to get used to. On the open road where the turning is minimal, it is hard to tell you do not have power steering. In turns, if you are moving the car while turning it is almost imperceptible that there is no power assist. Tight turns, or turns when parallel parking do require more effort but again, if the vehicle is moving, it's really not that much more. If you are stopped and trying to turn the wheel, then yes, it requires some effort. But how often will that happen? 2 Link to comment Share on other sites More sharing options...
Guest honestb Posted July 1, 2016 Share Posted July 1, 2016 Hi i am still looking for the manual set up for the 52 super.If you have them please post or email me at belvinbryan@sbcglobal.net thanks Brian Link to comment Share on other sites More sharing options...
MrEarl Posted July 3, 2016 Share Posted July 3, 2016 honestb , I'd suggest starting a new thread in the Buy/Sell forum for a manual set up. And perhaps add your location to your profile or signature. Link to comment Share on other sites More sharing options...
Guest honestb Posted July 3, 2016 Share Posted July 3, 2016 will do thanks Link to comment Share on other sites More sharing options...
Beemon Posted July 4, 2016 Share Posted July 4, 2016 On 7/1/2016 at 6:32 AM, JohnD1956 said: if you've ever had to turn the wheel of a car where it did not work, you know it's very difficult. It is extremely difficult, worse than manual steering. If you get a junkyard box, make sure to have it professionally rebuilt so there is a warranty and dependability. Link to comment Share on other sites More sharing options...
Mauro trevizan79 Posted April 3, 2022 Share Posted April 3, 2022 On 13/10/2012 at 14:50, Erik said: Sim, o balanceador harmônico para PS tem duas ranhuras. Um para ventilador/bomba de água e outro para bomba PS. A configuração de '52 era a caixa de direção original com o PS construído em cima. Do braço pitman e para fora, tudo é o mesmo, mas como o eixo de direção foi encurtado para acomodar o PS, toda a coluna, articulação da engrenagem, suportes e parafusos são diferentes. Roda, braço/mecanismo de sinal, buzina etc são os mesmos. A versão curta para a troca é: Desconecte o braço pitman, a articulação da engrenagem e os suportes das colunas de direção etc. Troque as colunas de direção. Substitua o balanceador harmônico. Monte a bomba PS. E agora a parte complicada: drene um pouco de fluido de resfriamento e remova o 2º e o 3º cabeçote esquerdo e encaixe o reservatório. Você pode considerar substituir a junta do cabeçote enquanto estiver nisso. Aperte TODOS os parafusos de cabeça de acordo com as especificações. Se você não tiver uma ferramenta sofisticada, precisará remover o conjunto do balancim e daqui para uma nova junta de cabeça é ½ hora. Faça o encanamento e sangre a bomba de acordo com o manual da loja e Bob é seu tio. look . do you have this double pulley for power steering. I have the original photo of a 1953 pontiac buick please . Link to comment Share on other sites More sharing options...
2carb40 Posted April 6, 2022 Share Posted April 6, 2022 No comprend? Pulley for Pontiac or Buick or just photo? Translation please. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now