36stude Posted November 6, 2008 Share Posted November 6, 2008 Im wondering if anyone here has ever removed doors off of a 1936 . If so did you remove the hinge screws ? Im a little concerned that I might not be able to replace them if I damage them . Or did you remove the door pins instead ? If so is there replacement pins? I have heard that if I install a hinge mounted mirror Ill need a longer pin anyways . Where does one get these pins ? Link to comment Share on other sites More sharing options...
SMB Posted November 6, 2008 Share Posted November 6, 2008 I removed the doors from my 37 which I assume is the same. I used penetrating fluid (50/50 mix of ATF and acetone), heat from a propane torch and an impact driver. I removed the hinge from the body. Several screws came out easily while most took a lot of patience - wiggling them back and forth and applying more lubricant. I haven't tried to remove the hinge from the door and if I can avoid it, will not. I believe there are replacement pins available. A knowledgeable friend told me that I will need to use some oversize pins in my hinges. I just assumed he knows where to get them.Overall, if you can accomplish what you want by just removing the pins I think that would be the best way to go. I'm sure pins could be made if they can't be found. If the pin is not turning when the door is opened and closed it may not need to be replaced.Isn't working on these old Studes a blast- always a new mystery to solve. Link to comment Share on other sites More sharing options...
36stude Posted November 7, 2008 Author Share Posted November 7, 2008 Your mix of ATF and acetone . Is that as good as PB blaster or other penetrants ? Thanks Link to comment Share on other sites More sharing options...
SMB Posted November 7, 2008 Share Posted November 7, 2008 I don't know. I read a comparison on Bob Johnstones Studebaker and Avanti website IIRC. It compared 5 penetrating fluids for effectiveness and cost. WD-40 was the least effective while the 50/50 mix of ATF and acetone was the most effective and the least expensive, so I tried it. Here is the information: "The April/May 2007 edition of Machinist's Workshop did a test of penetrating oils where they measured the force required to loosen rusty test devices. Buy the issue if you want to see how they did the test. The results reported were interesting. The lower the number of pounds the better.Penetrating oil . Average load .. Price per fluid ounceNone ................. 516 pounds .WD-40 .............. 238 pounds .. $0.25PB Blaster ......... 214 pounds .. $0.35Liquid Wrench ... 127 pounds .. $0.21Kano Kroil ........ 106 pounds .. $0.75ATF-Acetone mix.. 53 pounds .. $0.10The ATF-Acetone mix was a 50/50 mix (1 to 1 ratio)." Link to comment Share on other sites More sharing options...
jerry kaiser Posted November 7, 2008 Share Posted November 7, 2008 I have a beautiful pair of 37 Studebaker Fender LightsThey are reproductions but you can't tell them from NOSI would like to trade these for other things I need.Such as The large 37 Pesident wheel covers, Center over rider - bumper guard, clock for 37 President, Side mount spare cover the face cover not the outside ring.If you need a pair of fender lights and haveany of these things to trade email studeblu@triconet.orgor call Jerry at (520) 979-0065 or (520) 616-0434 Link to comment Share on other sites More sharing options...
keiser31 Posted November 8, 2008 Share Posted November 8, 2008 I have always found the hinge screws come out a lot easier if you use an impact driver to try and tighten them a little bit first. Then, taking them out is much easier. Link to comment Share on other sites More sharing options...
36stude Posted November 8, 2008 Author Share Posted November 8, 2008 I think my craftsman Impact only goes 1 way. Correct me if Im wrong Link to comment Share on other sites More sharing options...
SMB Posted November 8, 2008 Share Posted November 8, 2008 That would surprise me. All the ones I've seen have a knurled ring which when turned reverses the action. But I haven't seen that many. LOL Link to comment Share on other sites More sharing options...
keiser31 Posted November 10, 2008 Share Posted November 10, 2008 Should be reversible...if not, a large screwdriver with pressure from vise grips will do the same task sometimes. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now