Jump to content

Harry Connors

Members
  • Content Count

    169
  • Joined

  • Last visited

Everything posted by Harry Connors

  1. Thanks Bob if I understand it correctly this section of the site will not change or? Harry
  2. How do we use/enter the new website? Thanks Harry
  3. Paul My 48 Continental has a tank plug, I used a wand and carb cleaner and cleaned the tank out, of course after draining it. I left it in the car and just jacked one side and then the other to get the cleaner in all of the corners. All kinds of interesting stuff came out. I pulled the fuel hose on the tank and fuel pump, then using my air nozzle for the air compressor blew out the lines. It seems to have worked. Since I did not have any rust come out I am debating if I want to use the tank sealer/liner fluid or not. I did not find a filter on my tank, it does not mean that it did not have one
  4. John I sure could use one. Interesting is that both the one that came out of my 48 Continental and the spare instrument cluster both have glass and they both are busted/cracked. I will contact you off forum. Thanks Harry
  5. Hi Gene thanks for the tip but I am stationed in Germany and the only glass shop that I know of and took it to said they could not do it because the glass was for a car! No Lowes here I am afraid. I will keep trying the ads and eBay. Thanks Harry
  6. Folks, anyone have an extra to sell or know where I can obtain the glass for the instrument cluster? I need to finish up the dashboard. Thanks Harry
  7. Folks I was trying to remove the chrome trim around my instrument cluster (48 Continental) and busted the glass cover over the instruments. I have an extra instrument cluster that has a good glass but the instruments are not so nice. What is the correct way to take the glass out of the cluster? I now know that the chrome trim has metal retainers on the inside. I hate having to learn the hard way. Thanks Harry
  8. Abe that is interesting, but what is a fuel injected Stromberg 97? I thought that they were carburetors. A fuel injected V12 would really make our engines run. I too would be interested in details. Thanks Harry
  9. I finally got the right rocker panel to fit well almost. There is a slight angle that goes from the floor board to the door inlet on the panel. Does anyone have a suggestion on how to get that angle in after the rocker has been spot welded to the floor at the top. Fitting it to the bottom of the U shaped inter panel make the angle on the bottom and the door jams on the rocker panel. I tried to get the angle in before spotting the panel to the floor (floor was marked where the original fit). This has used up about 20 hours of my work time and I still do not have the panel on right. I am open to
  10. Thanks again to everyone especially Doug Johnson who cut the piece out of a car he was junking. I sandblasted the part, measured it and then cut that area of my trunk out. After fitting and welding, I do not even have to lead the area. I had a good day today. Just a little hammer and dolly work and some clean up with the grinder disc and it looks great. Thanks again Harry
  11. Thanks for the offer Lee but I now have three of the chrome end pieces. The one that came with the cable was the best so that is the one I will use. Interesting is that all three of mine were held on my a small screw not an allen head one. I am almost finished with the assembly of the dash with almost all new chrome parts, except for the rims on the clock and speedometer. I could not find them so I just cleaned them as best as I could. My original lock unit is as Peecher says, it has a cap on the back of the unit. I am going to check my steering column anyway and see if it has a hole for the l
  12. There is a unit almost like mine on eBay.com right now the number is 251010844955 Thanks Harry
  13. I purchased a new ignition lock off of eBay mainly for the nice chrome piece that you pull out after you turn the key on and before you push the starter button. This one looks just like the one that I took out of my 48 Continental Coupe EXCEPT that it has a thick cable going to a mount that the steering shaft fits into. When you turn the key on and pull the chrome piece out the end of the cable that is fitted with a solid plug is pulled out of the steering wheel shaft. I hope this makes sense. My question is: Is this a proper part for a 48 Continental or was it an option? It would make it a lo
  14. Thanks to all of you for the response and especially to Doug who is sending me the piece. I finished the welding and leading of the rear of the body and hope to have the right rocker panel on this weekend (due to the job I am limited to Saturday work time on the Lincoln). It may get finished after all. Thanks again Harry
  15. Jim I could use one, please contact me at connors@online.de Thanks Harry
  16. I just finished leading and doing the fine sanding of the rear of the Lincoln Continental Coupe and have most of the replacement of the right rocker panel finished. I have run into a road block on the replacement of the front floor panel, from the door post forward, to the firewall. Mine is gone on the right side along the side panel and I need one desperately so I can finish off the welding. Does anyone know of someone who will sell me the front part of a floorpan from the doorpost forward for the right side? I have tried Classic 2 Fabrication and Paul Bradley (waiting on answer as I am sure
  17. Thanks Douglas, I just sent you an email with a photograph of the piece. Harry
  18. I would like to thank everyone who answered me on and off of the forum and who sent me photographs of the floorboards and trunk area. You guys are really the best source of information on these cars there are. A new question, based on the photographs I received on the trunk area I spend some time with the body parts book and found a parts number for the plate i need 06H 5643252 Plate rear deck door striker is what it is called. Does anyone know of where I could get such a striker plate? Or if they have a continental that they are scrapping out that could have the plate cut out of? Since this i
  19. Thank you Tom, that explains everything I needed. Harry
  20. There are some on eBay right now, they were not very much. Harry
  21. Tom Thank you very much, the part of the trunk lip I was looking for is that part that has a plate protruding in the middle at the rear. Is that just a flat plate welded on for the lock tab to hook under? I welded in a u piece at that location as there was just a hole on my car. Thanks Harry
  22. Folks I am fishing for photographs again. I had to weld in a piece of the U channel where the rubber seal fits into on my trunk top. Of course it was right at the area that the locking piece on the trunk lid locks onto. Since I had about a six inch area that was rusted away I just made a U channel to weld in. It looks great but is there supposed to be a slot for the lock to secure the lid? I guess what I am trying to say is does anyone have a photograph of the top middle of the body at the rear in the middle of the trunk area? Thanks Harry
  23. Thanks to everyone who has answered the question on the floorboards I have written Paul Bradley to see if I can get a set from him. Thanks again Harry
  24. Got it Dennis and I have sent you some photographs of the insides. Harry
×
×
  • Create New...