n1gzd

Members
  • Content Count

    205
  • Joined

  • Last visited

Community Reputation

0 Neutral

About n1gzd

  • Rank
    Senior Member

Contact Methods

  • Website URL
    http://www.pangalacticconsortium.com/cars/cars.htm

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. That looks like the part on my '36 Plymouth. Rebecca
  2. My 1936 Plymouth has a cowling that hinges on each side of a center strip that runs from the top of the radiator to the top of the firewall. there is a metal piece that the center cowling strip slides into at both ends. I just figured out that I am missing a chrome piece that is supposed to fit on top of this and pin it down so that it stays in place. I don't think that anyone manufactures this. Does anyone who knows what I am talking about know where I can get these two pieces? I thought I would ask before I spend a lot of time trying to make them myself. Thanks, Rebecca
  3. broom handle is a good idea. I might use that if I can't figure out how these things from Roberts are supposed to be installed. Rebecca
  4. I went ahead ordered these but the guy from Roberts was unable to describe how they work so I will find out when I get them what they look like. Thanks for the tip. Rebecca
  5. (questions at the end after this background info) My the metal on my hood is worn and probably some day I need to rebuild parts of it. I have replaced the hinge hardware that it hooks on at (on the car at the front and rear of the hood). I gather that the owner of the car was supposed to just lay the open side of the hood over onto the other side. I don't want to do that (scratch the paint and stress the hinging surfaces even more) I have two S shaped hooks that I hang on the radiator support rods (given to my by the prior owner). This is not a great solution either because it hangs a little bit low and you have to be careful not to scratch the sides of the car with the corners of the hood. I have seen fords with a prop rod that is bolted across the support rods at right angles (about 7 inches from the firewall). This seems to work pretty well and keeps the hood corners away from the side of the car. I got one of these prop rods (the one from speedway) but it is way too short. I should have measured one before ordering it. Now I am planning on building my own. I have a couple of questions: 1) Has anyone else built their own? Can I see pictures. Did you go with one rod or two (our hood is longer than the Fords). 2) Has anyone redesigned the way their hood hooks onto the car? This is really not a very good design. It should have some kind of captive pin that acts as a hingepoint (and you would have to unscrew the hardware on the car in order to remove it). If so, can I hear about it. Thanks, Rebecca
  6. Thanks, I was not sure that solder would be strong enough but I am glad to hear that the bracket is attached by solder because it will take less heat to fix it. (don't want to damage the tank). I should be able to gently melt it with a propane torch. Rebecca
  7. Is the bracket that the radiator/hood support rod bolts to at the radiator end (two of them, one on each side of the top of the radiator) stuck by soldering or brazing? One of mine is lifting a bit and I need to fix it. I guess the trick is to do it without damaging the tank part of the top of the radiator. Thanks, Rebecca
  8. The later readily available motor mount did not fit (no clearance to install it because it has 4 studs instead of 2 studs and 2 bolts. After trying to instal that one in the end I ended up modifying the engine side instead so that the original style rubber mount would fit. I got an NOS one that was in pretty good shape and installed it. Rebecca
  9. I am replacing all of the ignition parts on my 36 coupe. It appears that my ignition coil could be orignial so I want to replace it so that I can eliminate a possible weak coil from some problems that I was having earlier (just want to start out with new ignition parts). I have what appears to be the original type coil that is mounted stuck into the firewall (and it might be the orignal one - it looks old). Bear with me, this is the first time I have encountered this type of firewall mounted ignition coil. http://www.pangalacticconsortium.com/cars/PlymouthGallery/imgpages/image019.html The coil ignition cable has a threaded connector on it (screws on, not plug). One coil power site is on the side of the coil in the engine area (forget if it is hot or ground). Inside the car under the panel there is what looks like conduit coming from the back of the coil and it runs to the ignition switch. I can only assume that this is the other side of the power to the coil that is switched through the ignition switch. Why did they do this, was it a security measure (hard to hot wire the car)? Anyway,here are some questions: I am guessing that there is a way to separate the coil from the firewall bracket and the metal conduit on the back. It was not obvious when I looked at it how it could disconnect and I did not want to break it. I pointed a flashlight on the back of the coil and all I saw was the conduit but in a catalog pic (andy bernbaum) I saw what looked like a connection for the other wire. <span style="font-weight: bold">Is there actually supposed to be two things on the back, ignition lock conduit and power wire?</span> The firewall mounted coil in both catalogs that I looked at is very expensive ($129.50 vs $39.50). <span style="font-weight: bold">I wonder if it would be possible to mount the cheaper kind in the hole where the original type goes and somehow snake the other power wire behind and leave the ignition lock conduit thing disconnected.</span> If the coil is the same diameter it might fit in the coil bracket and look kind of stock. Has anyone done that? I have noticed that the later cars have the coil mounted on the loom thing that routes the igntion cables. I really would rather keep mine in the stock location. <span style="font-weight: bold">Here is another question: When I removed my old ignition cables I could not find a way to separate the two sides of the ignition cable loom thing so I removed the contacts and boot from the ends of the cables.</span> I have some new cables but I don't want to take them apart. Is it actually possible to separate the two halfs of the loom thing or do you really need to build the cables on the car? Thanks, Rebecca
  10. while the radiator was out and I had the water pump off I gave the water distribution tube a little tug and it came out easily. With the grill on I was able to pull it out about 3/4 of the way. It looked like it was in such good condition that I just decide to push it back in and leave it. Rebecca
  11. thanks again. I will start by just inspecting it and seeing if it looks badly rusted and if it moves when I pull on it. Hopefully this weekend I can get to this. My front engine mount project has to come first. Rebecca
  12. I guess the question that I should have asked is: how long is the water distribution tube? That would have told me everthing that need to know. Of course, now that I have seen a nice picture of one on another board I also know what it looks like (including the length of it and a nice description of the fact that you can actually tilt it down a little when you are pulling it out such that it takes a little less room). Thanks. Rebecca
  13. Since I have never removed the water distribution tube I don't know how long it is. If it is as long as the block then it is obvious how to tell if there is room. That is all I needed to know. Good grief. Rebecca
  14. Is it possible to remove/install the water distribution tube without removing the grill? I have of course removed the radiator. By the way, I am having some trouble removing the water pump. Two studs and one bolt are removed. I just seems to be hung up on the bottom stud. Shall I just try harder or is there something that I did not know about? Thanks, Rebecca
  15. In my state it is legal to have no belts (if car did not come with them). In my other cars I just drilled the holes just behind the bench at about the width of a person. Rebecca