Old26Buick
-
Posts
417 -
Joined
-
Last visited
Content Type
Forums
Gallery
Events
Posts posted by Old26Buick
-
-
I have a 27 Standard engine and complete ru nninggear. I think the parts are differant. I think I have a 26 Master trans.
- 1
-
19tom40
I have found kits to convert to C-40 Ford auto without modify the frame. Also kit to change to open drive and also kit to beef up the rear wishbones.
-
-
I'm thinking on putting a auto trans and electric power steering in my stock 48 Ford Conv. Any idea what cost would be ?
-
I'm thinking on putting a auto trans and electric power steering in my stock 48 Ford Conv. Any idea what cost would be ?
-
Is this clutch like a 27 Standard. I rebuilt mine myself
-
when replacing with modern seal does lip go towards grease or away from it.
-
What is best way to remove rear hub on a 27 Buick standard. Felt seals are leaking. Going with newer grease seals. Thanks for any Help.
-
I have changed to down draft on my 26 and my27 Buicks, Never ran so good. Used a 41 Chev 1 barrell carb, Did away with vacumn tank, Electric fuel pump near tank and fuel pressure regulator on firewall used about 3 psi. Never have had to use the choke. Good luck
Steve
- 1
- 1
-
On 2/26/2021 at 10:15 AM, A.A.Ron said:
Steve, do you recall what adapter you used for the down draft? I have a 31 series that I am looking to do the same flip as well as a few other upgrades.
I made one out of a piece of steel. I drill a hole that was size of intake manifold. Used a 40 Chev carb with bigger opening. So used a larger drill and make a taper. I can email a drawing.
Steve
-
just using rattle can enamel
-
years ago I painted the plane blue which was a mistake as orginal colors weren't that bad.
-
I replace the dist on both my 27 and 27 Buicks. Used a 28 or latter dist and can get point cap, rotor and cond. from any parts place for around$45.
-
should have stated this is a pedal car
- 1
-
I bought a set from Bob for my 27 Buick and very good, fit well.
-
looking for correct blue and red for my pursuit airplane, I have found the silver paint Thanks
-
We are planning on attending with our 27 Buick Woodie. Is there a place to park truck and trailer ?
Steve and Margaret Smith
Falmouth, Me
-
Roger Barrett,
Thanks, just what I was looking for. I can get both seals which would be the best. Have replaced the felt about every 2-3 years even with fluid doen an inch. Going to check shaft for smoothness. Thanks again
Steve
Falmouth Me
1927 Buick Woodie wagon
-
Someplace I read where you could replace the felt seal with a modern oil seal. Mine still leaks after lowering gear oil level. Thanks for any help.
-
On both my 26 and 27 Buicks I used a end section of 28 gen. and used a 28 Dist. Actually you can use quite a few differant later GM dist.
Haven't had any trouble in over 10 years. Got all the parts from NAPA. Good luck
-
have had both my 26 and 27 Buick done at local muffler shop. Alot cheaper than sending away for kit.
- 1
- 1
-
I just installed new hood supports from Speedway. Fits 42-48 Ford only. Worth looking at them. Hood never shut so good and very little gap by firewall.
-
I just installed new hood supports from Speedway. Fits 42-48 Ford only. Worth looking at them. Hood never shut so good and very little gap by firewall.
-
TO 19tom40.
Actualy all I couild fine here was copper at O'Reillys $25. universal set Thanks.
Steve
1926 Buick Standard 20
in Buick - Pre War
Posted
I had a 26 Buick Standard and now a 27 standard Woodie wagon. On both Buicks I fliped the intake manifolds and used a 41 Chevy Carb. Never run so Good. Also put in a 28 Buick dist. with mechancial advance in side the dist. Can get all the parts at NAPA. Good Luck