Jump to content

1938McLaughlin

Members
  • Content Count

    55
  • Joined

  • Last visited

Community Reputation

0 Neutral

About 1938McLaughlin

  • Rank
    Member
  1. I have the following items for sale. Items removed from a 1966 Riviera. Radiator POSI diff. with 3:07 ring and pinion 1" intake risers - new axle shafts center console tilt steering column front hubs headlight assemblies Grill turn signal assemblies Dash cluster iwth electro cruise Heater and A/C assembly Alt. Rear brake drums Remote trunk release - including switch Contact Ed 519-648-3915 edz240@yahoo.ca
  2. I have the following items for sale. Items removed from a 1938 McLauglin BUICK Fuel Tank Radiator Ring and Pinion 4.44 ratio L & R axle shafts Steering column with Steering wheel ( not banjo type) Dash center trim piece - chrome Ash trays- pair Headlight switch Fog light switch Arm rests - front door Front brake drums ribbed - 6 bolt Mclaughlin Rear Brake drums ribbed - 6 bolt Mclaughlin Brake baking plates with hardware - front and rear - shoes are virtually new. accessory Grill guard interior door handles (2) - stainless repro. Pair 6V horns Hand brake lever assembly clutch and brake ped
  3. Any chance you have the Stainless Running board trim? Also door sill trim. thanks Ed
  4. That makes sense to me. Explains why the middle bolt holes are closer together on the side angle support pieces. And more importantly I just could not see getting a single piece large enough to cover the hole area, to go it at once. Excellent description Jeff. thanks Edward
  5. wanted. - Front bumper for a 1938 Buick Special - good condition (no damage) - Interior rear view mirror. thanks Edward
  6. I have a 1938 Special 4dr trunkback. Unfortunately the car was incomplete when I got it, everything in the trunk was missing. I need to come up with a pattern/ picture/ detailed description of the raised portion of the floor that sits above the spare tire. What type of material was it made of? thickness? Is it a single piece? ...if not, were does it join? How far to each side of the support does it go? Any and all help appreciated. thanks Edward
  7. The pair of "SPECIAL" emblems I have are Stainless steel wrapped around a steel backing plate. Background color is painted the same light silver gray as the painted portion of the side vents. Ed
  8. The Horn ring and center are for a '38, personally I would hang onto them until I had may hands on a better one. Sometimes you're lucky if you find just the steering wheel. "strange thin chrome 3/4 circle rings. not sure what theyre for." Not sure what diameter of circle they make. But I would guess they may be for the side covers for sidemounts.
  9. I question whether your overheating problem is truly cooling system related. Could be, but I going to pick at some other possibilities. You mentioned some squealing from either the water pump or generator. This could simply be a loose or aged belt. A belt if it gets really hot from slipping will glaze up get very smooth, further reducing its ability to grip/ spin the pulleys it is driving. There is a drain cock for coolant on the engine, located on the right side of cylinder water jacket at the rear. If coolant drains readily from here, and has no crud in it. I'd say your system is fine, and
  10. Just a couple ideas. First one I would be inclined to attempt, is running the exhaust from the drivers side along the original path, but instead of joined the right side continue it all the way back and have it exit on the passenger side. Then run the exhuast from the passenger side back and cross it over to the drivers side at the rear. That way the two pipes would end up being similar in length. Just don't make the diameter to big, you want to keep the velocity up The other option is to have a nicely made single system of adequite size made up (mandrel bent). Much of the stuff muffler shops
  11. Thriller I just got some new replacement engine mounts for my '66 riviera at Napa Part # 602-1026 Transmission mount n/a
  12. I am parting out a '66 Riviera. No engine or trans, I needed them. Black interior, bucket seats, trim panels. Doors, hood, trunk lid, rear bumper, grill headlights, posi rear end. Located near Kitchener, Ont. Canada contact Ed: edz240@rogers.com
  13. If I understand correctly, you've got flex pipe all the way back. Flex pipe has a huge amount of resistance/ restriction . It is not good for flow, a smooth pipe will flow much better. I suspect that all the wrinkles in the pipe change the sound considerably. Skip the cut-out, when you can afford it get a proper exhaust made for it.
  14. I believe you will find the the rocker arm shaft is pressed into the towers that support it. Might not be so simple to dissassemble.
  15. Sorry for scaring you in the previous post. Looked at your first pic again. I've put a green line where the line is to go. And yellow circles where the oil should come out from rocker. Take and remove the extra line from the first T and plug it. Then start the engine and see where the oil is flowing or not. Help diagnose what to do next.
×
×
  • Create New...