Jump to content


  • Content Count

  • Joined

  • Last visited

Everything posted by NASCARLady

  1. DKirk and DAVES89 -- Thank you both for additional information. I've done some additional searching. When I expanded my picture of the second dangling switch, I could see the shape of the switch more clearly. I was then able to look in a shop manual for an 89 Reatta (a year earlier than my daughters car) and found a picture of a door ajar switch (see attached). This looks like the dangling switch except mine appears to have the plastic piece with mounting screw tab broken off. PS: My daughter just visited so I was able to see if lifting the outside handle would wake up the dash -- It d
  2. KDirk -- Thanks for the explanation. Since the switch with the clip is intact, I should be able to clip it back on the cylinder. Now I have to determine where the second switch (in my last picture) goes. It would appear to be part of the latch mechanism. However, it looks like the plastic mounting is broken off. So maybe it was an integral part of the latch.
  3. Ronnie -- Thank you for the picture. It looks like the switch in my second picture includes the clip and should be reinserted to hold the cylinder. I'm not sure how to position the switch but maybe the rubber plunger on the switch is actuated when the key is turned clockwise to lock the door.
  4. Frogware -- Thank you for the picture -- that helps quite a bit. It's still not clear what holds the cylinder in its proper place --
  5. The drivers door key cylinder is hanging on my daughter's 1990 coupe Reatta due to her overzealous friend that used a slim jim to unlock. If you hold the cylinder in place the key will unlock both doors and will lock the drivers door. I took the door apart to find two switches that are hanging by their cables. One cable has a U-shaped bracket that looks like it would fit around the cylinder. The other switch looks like its mounting bracket is broken and looks like it should be attached to the latching mechanism. I also found a melted amber plastic piece that may have been holding the cylin
  6. Thanks much for all the help. The rest of the story ...... Took the car to the A/C shop and owner Grant [B&M Radiator in Fremont, CA] pulled about 1.4 lbs of R12 out. That's my bad because the new low pressure switch that I put in had the plastic thread. I was afraid that I would over tighten but I didn't discover that until the car had lost about 1 lb of R12. Grant took out the new low pressure switch and put in a new O-ring and re-installed. Grant evacuated the system and recharged. He disconnected the battery to reset codes. When I turned on the car the compressor did n
  7. OK, I'll take the car to the A/C shop and refill the freon. Chuck
  8. Thanks for the good suggestions. I ran two tests, each test starting with resetting codes by disconnecting the battery. Test 1 -- Low pressure switch in place Results -- Now seeing B448 code; compressor not running; B027 reads 20, B028 reads 20 Test 2 -- Low pressure switch disconnected and jumper across connector Results -- No B448 code; compressor is cycling with approx 5 seconds on and 5 seconds off. B027 cycling from 23 to 31 and then back down to 23. B028 cycling from plus 9 to minus 2 and then back up to plus 9 Do these measurements show that I
  9. Updated information -- Found that the fuse blowing resulted from the suppression diode was breaking down with higher heat. Replaced the diode and that problem was solved. Then noticed that compressor was not cycling and system was getting very cold. So I replaced the low pressure switch. But now the low pressure switch does not turn on so the compressor does not come on at all and the diagnostic throws the B448 code. So I removed the connector from the low pressure switch and jumpered the connector. This causes the compressor to come and stay on and their is no B448 code. Any sugges
  10. Thanks much for your help. I checked BD27 engine cold, reads 27. Then with engine running and AC off, reads 31. Then with AC on, reads 54. Then keep engine running and turned off AC, went to 33 but started inching up to 44 over about 3 minutes. Then turned on AC again, went back to 54 but soon after fuse blew. I'm wondering if the high side temp sensor is not working? Chuck
  11. Are there any suggestions on how I can monitor the BD27 in the 1990? Chuck
  12. Thanks for the quick replies. Within the family we have two Reatta's 1989 and 1990. The 1990 is having the A/C problem. I will check on the items that you have mentioned. One question -- The 1990 doesn't have the CRT (like the 1989) so how can we monitor the BD27? Also, the schematic shows a diode across the clutch coil to reduce the inductive kickback. Has anyone had a problem with that diode failing [shorting] at high temperature and causing the clutch fuse to blow? Notes say the diode is inside the connector on top of the clutch coil. Is it possible replace the diode without
  13. Yesterday I had an experienced A/C repair shop in San Jose, CA evacuate and recharge the R12 (it was only down 0.4 lbs from full at 2.375 lbs). The A/C worked fine for about an hour of driving [Note air temp is record heat wave at 96], then the 20 amp fuse #19 blew and compressor clutch stopped operating and Service A/C light came on. Any ideas of what could be causing this problem? Chuck [husband of NASCARLady
  14. C.F. Massie -- Thanks much for your great post on removing the door panel. Note: the strap bolts are 10 mm. C. Roedel
  15. Howard, Thanks for the quick response. I have to be out of town for a week so I will try upon return -- Leslie
  16. Thanks for the great posts on repairing the '89 window switch. One question -- I can't find the C clip to remove the shift handle. Please help --
  17. Jim, Thanks very much. In reading your message from a few months ago, it suggested that I clear the codes and then check the condition again. It worked! I had the problem of Very Low A/C Refrigerant cause the compressor to remain off. Replaced the low pressure switch, had the system evacuated and recharged, but the error message was still preventing compressor operation. The A/C shop wanted to replace the ECM, but I held off. Clearing the code solved the problem. By the way, the '89 shop manual page 1B1-4 Figure 3 incorrectly reverses the position of the low refrigerant pressure switch an
  • Create New...