-
Posts
126 -
Joined
-
Last visited
Content Type
Forums
Gallery
Events
Everything posted by KQQLCAT
-
1962 Olds Dynamic 88 source for grommets and fasteners
KQQLCAT replied to gregleck's topic in Oldsmobile - Technical
Fusik has this stuff. -
CAR IS SOLD
-
That block casting number when cleaned up should turn into 577476 I have 2 61 blocks and both are 577476.
-
-
So as I am reading both threads on the spacers they seem to be making one set at .325 (slosteve) and the other at .25 (JRivi64)Not sure what to do here. I will measure what I have since mine is a full size car even they list the same bushing. Pat
-
I am so glad I found this thread, I was giving up on buying new bushings till I read this. I have ordered the bushings listed here and will attempt this procedure. Before I make the spacers has anyone decided to sell them? Thanks Pat
-
Looking for a Carter AFB # 3645S
-
I will email you. Thanks
-
I am looking for a nice 63 Buick Wildcat hood with no rust.
-
What is the one Oldsmobile U wished U owned!
KQQLCAT replied to Steve Moskowitz's topic in Oldsmobile - General
#1 1957 Fiesta Wagon red and white Would be the one for me. #2 Would be a 1961 Starfire black with red interior. -
I have a shifter if your interested. Pat
-
I am looking for a trim piece for the drivers side front bumper that is next to the turn signal. I need the upper piece. Here's a picture. Part is # 14 on the 61 Olds picture. Thanks, I FOUND IT THANKS Pat<!-- google_ad_section_end --> <!-- / message --><!-- attachments -->
-
I am looking for a trim piece for the drivers side front bumper that is next to the turn signal. I need the upper piece. Here's a picture. Part is # 14 on the 61 Olds picture. Thanks, I FOUND IT THANKS Pat<!-- google_ad_section_end --> <!-- / message --><!-- attachments -->
-
I have been looking for rear control arm bushings for my 1961 Olds 88 and have not found anything at all. Looked at old moog parts books and they didn't list them. I looked at my Olds parts book and they sold the whole control arm. Is there a company out there that rebuilds them? Thanks, Pat
-
-
I found a 61 Starfire supplement manual on ebay and purchased it in hopes to get an illustration of this console. Pat
-
I have repaired all the cracks and reinforced those areas. Now I need to order the glove box from Fusik and get a picture of the diagram that shows how it goes together. Pat
-
First it has window switches and I have the filler pieces and 4 of the floor braces. I have a couple other braces that I don't know where they go. A X bracket and and a a piece I fabricated from a rusted out piece that I think goes on the X shaped piece. I have the wiring harness and tach also. I am looking for the piece that the electric windows goes in that would not have electric switch holes in it. It would be nice to look at a diagragm. Thanks Pat
-
I am looking for a copy of a parts brake down for a 61 or 62 Starfire console. My manuals don't include a Starfire. I am restoring a console I got out of a 62 Starfire. Anyhelp would be appreciated. Thank you, Pat<!-- google_ad_section_end --><!-- / message --><!-- sig -->
-
This Carburetor Shop is in St. Paul MN. I will try to readjust idle screws. How many turns out after engine starts to kill?
-
I have a 1962 Olds Rochestor 4GC that is giving me problems. A little history. I am converting my 61 Olds 88 394 from a two barrel to 4 barrel. It ran fine with the 2 barrel but I had to do a valve job and since I had all the parts to convert it and had it all apart I figured I would change it out. I had a local carb rebuilder (The Carburetor Shop) restore/rebuild this carb. It looks great but It has 2 problems. It has a major bog when I touch the accelerator and if I get into the secondaries and go to idle it has a real rough idle untill I pump the accelerator a couple times then it idles smooth again. I plan on taking this back to the rebuilder but I want some ideas to tell him to look at. Thanks for any advice you can give, Pat
-
I am puting on a 4 Barrl carb system on my 61 Olds Dynamic 88 394 and need to know how the vacuum lines are routed. It's from a 63 Olds 394. The throttle stop valve etc. Thanks Pat<!-- google_ad_section_end --><!-- / message --><!-- sig -->
-
I have a 4 barrel intake with a casting number of 587503 and a D1 on it. I was told it came off a 64 Jetstar 1. Does anyone know for sure? Thank you, Pat<!-- google_ad_section_end --><!-- google_ad_section_end -->