Dan Marx

TWO NOS pistons for sale 1- 1922 EJ 1-1923-24 EM

Looking for 1928 Essex super six 4 Door frame. Any chance there is one available? Dan Rembert, SC

This RBM switch has been sitting on the shelf a long time. Is this an after market switch or perhaps an OEM for some manufacturer? What's it fit? Thanks Dan

I need 2 lower window channels for a 1942 Ford truck. I am sure this was used for many years. I have posted a pix of it. Channel is 28.25 inches long with 4.5 inches between the carriers. Thanks Dan Marx

Looking for a Clevite reference for some old cam bearings to fit a 1960-64 GMC V-12 engine. Any help would be greatly appreciated. Dan Marx

one in great condition just sold for $27,00 at Barret Jackson, Las Vegas.

I have a '42 Ford ambulance that started life as a Panel Delivery. I need 3 exterior door handles. Dan 803-549-2187

Need three door handles that fit a 1942 Ford Panel Delivery. Contact Dan at dlmarxatbellsouthdotnet thanks.

I believe this door latch would have been used from the late thirties to late 40's in professional cars.

Tom The left hand side door latch is missing. The one I have works fine. Just need to locate the left one. Thanks for your time Dan

I am in urgent need to identify uses of this door latch, then I need to acquire one. This is on my 1942 Ford Ambulance right hand rear door. I need the left! This Ford ambulance was converted from a Ford Panel Delivery at the Siebert Shop. I am sure this was an off the shelf door latch, I can't imagine it being made special for this vehicle. Any help would be greatly appreciated. Perhaps there is some one who deals in door latches. Thanks Dan dlmarx@bellsouth.net

Starter Solenoid Switch, 1542, cover 1853343. Used on Cadillac 1936-41, and LaSalle 1937-40 This an NOS cover. The box was opened to photograph it. $30, postage included.

After a closer look, you are correct. it is 1873759. Thanks Dan

Thanks, really appreciate your time. Dan

Housing is not used. Nothing stamped on housing. The Delco Remy tag is blank. Dan

Exhausted all my sources, can any one help me identify the application of this distributor housing. Thanks Dan

Thanks

This is a pair of pistons for the following early Studebaker: Parts books says they fit 1922 EJ and 1923 and 24 EM .004 oversize with 11/16 diameter piston pin. Four ring type. Special thanks to StudeBoy for taking the time to ID the pistons. $50 plus $13.95 USPS medium flat rate postage for the pair. contact Dan at dlmarx at bellsouth dot net

Thanks. greatly appreciated. Dan

These were bought with a set of Light Six pistons, which have been sold. I am only assuming they could be Studebaker, they have a part number of 45550 printed on the top of one of the pistons. Diameter 3.125 in Height 3.380 in calculated compression height 1.938 in Thanks in advance for any help identifying these pistons.

Pistons have been sold. Thanks to all who responded.

OK, I have 5 TRW CR1325 connecting rods that have been reburbished. I cannot find a reference for these to confirm the application. They were previously marked 1955-59 Cadillac. However, the '59 caddy had a 390 ci engine. Any help identifying is greatly appreciated. Dan

I need the trim that goes from the wind shied, down thru the side of the dash and goes to the floor behind the kick panel. This trim held the wind lace and had the window extensions used to push the bottom of the window out attached to it. Thanks Dan Marx

Check '41-47 Chevrolet. Dan

Trying to find an application for this bushing. I know it is a leaf spring split rubber bushing, but I cannot find any application,. Harris Rubber 60100 Thanks