[1920's Wooden Wheel Rim clamps and Bolts]

Are any of these bolts 7/16 x2.5 long 14 tpi. I am looking for bolts for the front hubs on aq 1930 dodge u133 truck. The six in the right side of your picture look like they are the type i am looking for. Thanks  George Waters

[drag link springs]

Does anyone have a source for the springs that go inside of the drag link? I have tried all the normal sources with no success. These are 15/16 in diam. and just under 1 in. long. These are for a u133 1930 dodge 1 ton truck with the solid drag link. Thanks George

[hub bolts for 1930 u133 dodge truck wood spoke wheels]

I would need all 16 for the for the front and 16 for the rear. Thanks  George

[hub bolts for 1930 u133 dodge truck wood spoke wheels]

 

 

does anyone know where to purchase the hub bolts for this truck? I know that i could use common carriage bolts,but the heads look wrong. The fronts are 7/16 diameter and the rears are1/2. Thanks  George

[how to disassemble a u133 ball and trunion ujoint]

How do these come apart to clean and replace the seals. Mine have lot of dirt and old grease in that needs to removed. Any pictures of these units to show how theyare assembled? Thanks in advance George

[Information needed -Dodge Truck.]

Looks really nice Paul.

[4 cylinder manifolds]

Try  Rapparts 477 Autumn leaves road starlight pa 18461  ph 570 798 0390 . I was there a couple years ago and he had a bunch of them in the barn. I was looking for parts for my u133 truck but he didn't have much that i could use.  George

 

 

[It only took two years to find]

 

for thirty dodge panel. If you contact George Farrell at romar he may have a reproduction mirror mount like pictured. What is the length of the tube that holds the mirror I have the mirror and bracket for my u133 but not the correct tube.  George?

[rebuilding Hannum steering box for my 29 DB truck]

4 hours ago, stakeside said:

Thanks for pic. 
the internals appear the same. Just a different side plate. Mine has Only has 4 bolts on plate. . See pic #2 in previous post.

I have eliminated some play using slotted screw on side.

try loosening #29 then adjust #25 you may get rid of more play.  George

[rebuilding Hannum steering box for my 29 DB truck]

I have a 1930 u133 with a hannum 4  steering box. I had a local machinist put new bushings in for the output shaft the inner bearings were ok after cleaning. I don't have the truck running now,but hat is one thing that is fixed.  George

[Information needed -Dodge Truck.]

If you can send me message or cell I may have a couple of those moldings. I could send a picture to your cell from mine. Your truck has the same fenders headlights as mine. My radiator and shell look like the one stakeside posted.  George

[Information needed -Dodge Truck.]

Your truck looks very similar to my u133 1930 .Look on the rear header in the cab for a data plate which if it is like mine will have the model# and wheelbase on it.  George

[Dig it up in a creek]

Where are you located and what steel part is missing?  George

[Dig it up in a creek]

This is a 1930 u133 cab and dash.  The door has four hinges and the opera windows are the same as my truck.  George

 

 

[sealing brake fluid reservoir holes]

The can is for my u133 dodge truck. I have repaired the holes but i would like to add a bit of extra security.  George

[sealing brake fluid reservoir holes]

What type of sealer can be used to seal pinholes in a brake fluid can? Eastwood said that their gas tank sealer would not work. I may try epoxy finish resin. I have repaired the hole etc.but I know if not sealed it will lea Thankyou  Georgek again.