NailheadBob
Members-
Posts
1,016 -
Joined
-
Last visited
Content Type
Forums
Gallery
Events
Everything posted by NailheadBob
-
Possibly @Bloo might have some knowledge on this subject. Oldsmobile Crankshaft part listings: Group #0.646 Crankshaft part #409511 fits 1937 thru 1939 8 cyl, part #412625 fits 1940 & 1941 8 cyl, and part #416847 fits 1942 thru 1948 8 cyl. So my thinking is the hole in rear of crankshaft must be larger diameter (why different part numbers for crankshaft) to mate up flywheel/torus cover (compared to a stick shift car crankshaft) Cadillac torus cover from 1941 thru 1948 had 30 bolt holes Oldsmobile torus cover had a 40 hole gasket part #8600088 for 1940 & 1941, and 2nd type part #8600515 (30 hole from 1941 thru 1948) Later I will look at same for Pontiac master parts book at "pontiacsafari.com>mpc" Bob EDIT: Paul Marsh Hydra-Matic transmission service manual #HM-1001 (RED cover) shows torus cover with 30 bolt holes.
-
Listed in the 1950 Oldsmobile chassis parts book: Group #0.666 Flywheel H.T. part #8601426 fits 1940 thru 1947 * * if used on 1940 or 1941 w/40 bolt hole type fluid coupler cover must use 1942 type cover part #8601427 and gasket part #8602257 Group #0.683 Bell Housing part #414123 fits 1940 thru 1942 / part #419504 fits 1946 thru 1948 EXC 1948 - 98 / part #555378 fits 1948 -98 Bob EDIT: Parts manual shows for Flywheel, has either a 30 Bolt hole type fluid coupler cover OR 40 Bolt hole type fluid coupler cover
-
Once you have check above suggestions and if still have issue, Another item when checking is the nuts holding the wire harness connections on back side of amp gauge if maybe vibration has worked them a little loose? Bob
-
Group #5.149 Lever, Parking Brake (In Rear Brake) part #1310548 (Right) and part #1310549 (Left) and only fit 1939 (40-60) Series Bob
-
Try “Delco Joe” Joe Hudacek in Wisconsin 715-392-6169 #3142694 gasket, between core and valve fits 1959 thru 1962 looks like o’ring Bob EDIT: 1959 Buick lists 2 different heater control valves #3146294 for manual control on e-Bay #1193224 for automatic control on e-Bay
-
Those Dang workbenches 😂😂 Bob
-
Do you have the factory chassis service manual? Do you have factory air conditioning? If so look in the air conditioning section, in a 1963 chassis manual it starts on page 11-59 and goes to page 11-67 Bob
-
Ever seen a '57 with a Hydro-Vac booster?
NailheadBob replied to Pete Phillips's topic in Buick - Post War
Thank you Pete, I will let you know. Bob -
Ever seen a '57 with a Hydro-Vac booster?
NailheadBob replied to Pete Phillips's topic in Buick - Post War
I know this a very OLD post BUT, and I see the Group #4.901 part #918866 fits 1957 & 1958 Buicks (it is listed in the 1958 Buick Accessories manual/book). @Pete Phillips, is this still available? Cadillac used this from 1950 thru 1954 Group #4.5000 Brake Package, Power (HYDROVAC) part #1462266 1950-1953, and part #1462157 for 1954, I know part number is different from Buick (maybe because of attaching brackets and parts) BUT booster unit looks Identical.. Bob -
I love your change of colors, I will be over to help you do the color change APRIL FOOLS Bob
-
Chicagoland Chapter alumni at Lisle
NailheadBob replied to AK Buickman's topic in Buick Club of America News
Gary sent me a group photo from the Buick National 2022 in Lisle, IL. and I will attach it here, Pictured from left to right: Gary Klecka BCA #1955 (also known on this forum as @AK Buickman), Larry Kuczek BCA # 826 (Larry recently passed away), Glenn Anderson BCA 2474, Jim Flaherty BCA #529, and Larry Guetschow BCA #2094 (Larry is on this forum but I don't know his handle/forum name) These are all LONG time members of the Chicagoland Chapter of the BCA. Bob EDIT: Anyone who attended the 2022 BCA Nationals would understand the umbrellas (lot of rain on early Saturday to make judging very difficult) just ask @Pete Phillips OR @lancemb. -
I worked at a Firestone tire store way back, and the owners decided we were all going to use anti-seize on all wheel studs, we also repaired semi-truck/trailer, road grader tires, 2 days after implementing the NEW anti-seize policy we had out first semi-trailer tire flew off and hit another car, Wuuu that was bad. NO MORE USING anti-seize on wheel studs anymore. Bob
-
1975 Buick automatic power door lock module
NailheadBob replied to Philippe Racicot's topic in Buick - Buy/Sell
Could you post photo of part with plastic shell on it so I can send it to a NOS vendors. I will contact the Technical advisor for 1974 thru 1977 Riviera from the Buick club to get his thoughts and possible contact person that may have the module. Did you contact the Buick Farm to see if they had part? Bob -
F/S G.M BRAKE DRUMS FOR 1936 / 1948
NailheadBob replied to pkr's topic in General Motors Automobiles and Parts - Buy/Sell
Any numbers stamped in the drum anywhere? Bob -
Does horn ring seem too loose on 48 DeSoto Deluxe?
NailheadBob replied to marcapra's topic in Technical
The screws/bolts you cut off, did it have shoulder on the bolt and that dimension is longer? (if that makes sense to you) Bob -
1975 Buick automatic power door lock module
NailheadBob replied to Philippe Racicot's topic in Buick - Buy/Sell
Maybe this may help, from 1975 Buick Chassis and Body parts catalog (effective April 1983) Group #13.090U Harness, electric door lock wiring part #8915727 Harness, auto. elect.dr. locks (incl. logic box & relays) BUT no logic box or relays for electric door locks that I could find. Maybe you could only get this part (logic box with relays) in 1975 with the wiring harness? From 1976-1977 Buick Chassis and Body parts catalog (Effective June 1977) They do show Logic module and relay for body wiring harness (for C, E w/auto. dr. lock) Group #13.095 Circuit breaker-logic module-relay, body wiring/ Relay part #8917266 C, E w/auto. dr. lock (1976 my) AND Logic module part #8917247 C, E w/auto. dr. lock (76 & 77 my) Have you checked all circuits on your module #8917246-C with a OHM meter? I don't see any burnt/separated spots on the circuits BUT possible solder break (poor contact OR maybe got to hot and melted a little) 3rd terminal from left on second row of 7 terminals (Maybe re-solder if that is a break in contact) I don't see any reason this could not work from the photo I see. Have you checked all wiring inputs from your service manual wiring diagram to this module? If you would like you could ship me your logic module and I could inspect and test it for you, just pay the shipping both ways. Here is another source for a replacement part: car-part.com and add all your car information and then fill out a request form and they will contact you about the part you need. I hope this may help Bob -
Help With 1950 Buick Estate Wagon Vent Window Frame
NailheadBob replied to Kartman01's topic in Buick - Post War
Oops I will edit the part number Bob -
1948 Roadmaster Convertible: Outer door handle
NailheadBob replied to 48BuickRoadConv's topic in Buick - Post War
-
Group #4.115 Bolt, Long part #1335079 up to trans #F-100 on 40-50 series, and G-100 on 70 series. Bob
-
From January 2023 post on @old-tank same issue with E-Bugle: I know this is a old post BUT did you ever get this resolved? I have the same issue, I went back through all of 2023 and ALL were blurry and most had blank pages, I contacted Cornerstone and they were NO help, I asked for contact information of the 3rd party NO they would not give that to me. I also contacted Melanie Mauser from the (CCBCA) Chicagoland Chapter of the Buick Club, she was willing to listen and help me, but she also contacted cornerstone and again NO answers. NOW all the ebugles are gone for me, there is NO listing of any, so I will not be able to complain about the blurry ones anymore? I am able to view other club magazines? I am not the best on computers, but I used to be able to view the ebugle, I probably could get my 7 year old grandson to figure it out, but I should not have to. Maybe I will just drop out of the Buick club? ( I don't need more magazines as I have the Bugles back to 1983) I am getting very frustrated at this point. Today 03/18/2024 my issues with google chrome continue with the BCA E-Bugle and is growing with other on-line websites, I contacted Apple/MAC on-line support and they told me my MAC computer is obsolete (I purchased in late 2014) BUT walked me through an update, my operating system #OS x 10.1 needed to be updated and after the Apple/Mac update I now have operating system #OS x 10.13.6 now with this latest update I now can view all of the E-Bugles and are clear and legible. Hoorayyyyyy. Sooooo my operating system on my computer was the fault of all my issues, I posted this incase future BCA members have this issue and give them a area to look at first. @JohnD1956 was kind enough to reach out to me by P.M. to try to help me and I thank you John. Bob
-
Adding the nut and washer would be the easiest, or you could tap and add a larger treaded shaft with a reducer to the original threaded shaft. Just my 2cents Not a bad tool from J.C.Whitney in my opinion, they have a location about 45 minutes from me, and we used to go from time to time, but now it is open for on-line sales only. Bob
-
Upon further review, master part book shows that is a "LONG" bolt, look at photo maybe bolt just pushed rearward? Bob