certjeff1

Members
  • Content Count

    123
  • Joined

  • Last visited

Everything posted by certjeff1

  1. certjeff1

    Starter Drive

    That is Delco-Remy #16810. I do not have any of that part number. What I do have is a 16798 which is the same design with a different gear. It might be possible to take 2 to make 1 good gear assembly. But I cant guarantee it. Looking at yours I don't think it is rebuildable. Jeff
  2. If you cannot find the armature and field coils or if you do find them but want spares for the future contact International Winding Co in Chicago IL 1-800-323-7521 they will rewind the armature and hand wind a new set of field coils. I have been using them for years. Jeff
  3. If you cannot find a set contact International Winding Co in Chicago IL 1-800-323-7521. They will wind you a new set by hand. I have been using them for years. You will need to send them the field coils, pole shoes and field case. Jeff
  4. When I talk about grounds do you have any small body grounds in the system. Most likely from the factory you only have a main battery ground. You might need to add small 12ga body grounds to the system. Adding them where? That depends on where you have mounted the light assemblies. You might even need to add one to the firewall. Since that is where you mounted the flasher. The more electronic devices you add the more small grounds you need. What kit did you buy from Snyders?
  5. I wonder if another electrical item is stealing the ground. My experience is if something works electrically by itself and then goes into any sort of improper operation with other electrical items operating. One of the other items is stealing the affected items ground.
  6. Are these for Autolite starter #MAX-4016 with solenoid #SS-4104? I have all kinds of boxes of studs without part number or application. Is the thread pitch 3/8"-16 for the studs? What is the outside diameter of the moveable contact? Jeff
  7. Add me to the list of having never seen battery conditioner.
  8. This is a 6v negative ground system with the push button grounding to complete the circuit. The difference between the standard Ford solenoid and the Lincoln is the mounting base. The Lincoln has a 3 9/16" center to center. A standard Ford is about 2 1/4".
  9. I am restoring a Lincoln V12 starter and I am in need of the solenoid. The solenoid is #SS-4004.
  10. Well knowing all that history. That generator was used starting in 1940 and was rated at 35A. The passenger car for 1937 was GBW4803A or C which was 22A. There charge curves are different. With all the added electrical items it makes sense that they went with the later unit. The regulator is Delco Remy most likely from a Chevy with 1118201 part number. Homemade wiring harnesses always gives me cause for concern when trying to troubleshoot in my shop.
  11. Not only do you have the diode setup but that is a Delco Remy Regulator. Somebody has spent quite some time and money previously trying to fix the charging issue. Since you just bought the car I would start with removing the generator and regulator and having both items bench tested as a set.
  12. I know Buckeye auto electric builds them in 6v. I don't know if they have a bracket setup.
  13. I make kits for most applications, but am currently out of stock on the bracket pieces needed to make the correct setup you need. I will have them in later this month to early February. Wherever you get your kit I recommend that you get the CS130 type Delco and not the 10SI type Delco alternator. The CS130 type turns on at lower rpms and gives better low rpm output then the 10SI type. This is important since you are adding an electric fan and you have a low idle speed car. Fewer people sell the CS130 do to their higher cost but there is a big difference in their charge ability over the 10SI.
  14. Trini everything you mention as possible problems are true especially on old starters. Whether it is a solenoid problem or an internal starter motor problem. If you are smacking the motor and not the solenoid how can you say is a solenoid problem and vice versa. You are not eliminating the wiring or solenoid activation, button or ignition switch. One of the most infamous jobs we got our hands on was a 1978 Corvette that had 9 starters from 3 different shops installed on it. Each one was replaced to fix the original problem. All 3 shops were smacking the starter as a test. We got the car here used our remote start button bypassing the system and made the starter work every time. After doing some voltage drop tests we found several crusty connections in both the positive and negative circuits causing the issue. If you want to smack the starter to try and get one more start to get your vehicle home rather then have it towed by some unknown tow service I get it. But don't make that your best most accurate test. M-MMan what you had with your Lincoln does not surprise me as Dyneto did a similar thing with their starter/generator combination units made for 1915 model cars such as Packard and Franklin. If you take power away from the starter field coils you lose the ability to charge even though all 6 coils, 3 starter and 3 charge, are independent of each other.
  15. As a 3rd generation starter rebuilder with 36 years experience nothing makes me cringe more than the smack the starter with the hammer diagnostics. I will give you that extremely worn brushes or worn contacts in the switch as a possible issue depending upon where you smack the starter. But a dead spot in the armature cannot not and will not ever be picked up using this method of diagnostics. Remember the armature is suspended at each end by bushings and has the tension of brush springs to overcome so the amount of force you will need to strike the starter to create a shock wave to effect a dead spot or move the armature ever so slightly off the dead spot is off the charts. If you have a dead spot when the starter is cranking it will lope, meaning it will slow down and then speed up each time any of the 4 brushes hits the dead spot. Whenever I hold a class at my shop I show people what dead spots look like and how starters act with them. Usually they never smack a starter again. If your local shop has gone thru the starter and solenoid I would use a remote start button and separate battery and bypass the system and see if it does or does not work. If it does work then you can go after wiring issues. DO NOT use 12v to test these starters as they have a very unique solenoid and are very expensive on the NOS market. If it does not work and you take it back you will sound more knowledgeable about the system and it will give them less of an argument then if you tell them you simply smacked the starter.
  16. There are only 2 coils used in that starter. Generally speaking Delco-Remy used 2 in 6 cylinder cars and they used 4 in 8 cylinder cars. It wasn't until they went to 12v that all Delco-Remy starters used 4 coils.
  17. I am looking for the electrical part of the turn signal switch for a 1956 Oldsmobile 88 w/hydramatic trans. Delco part#1995801. Thanks Jeff
  18. I am looking for the electrical part of the turn signal switch for a 1956 Oldsmobile 88 w/hydramatic trans. Delco part#1995801 Thanks Jeff
  19. My experience is the vast majority of 6v conversions are do to slow cranking. I always ask the customer to trust me that I can fix the issue without converting to 12v or simply installing an 8v battery. Both of which can come with negative side effects. Things that I have found are wrong size cables as has been said earlier. Usually store bought premade 2ga cables in the bubble pack. 6v needs 2/0 or larger. The other issue with these cables are they usually use steel ring terminals and not copper. I tell people to take a magnet when cable shopping if either the clamp or ring stick to the magnet don't buy it. You should do the same if you have cables custom made. Grounds are always lacking on classic cars even from the factory. Electricity is a learning process even for the engineers. Look at modern cars and all of the grounds they use. So adding small battery to body or main battery to frame or block is always good. In some cases cable location as has been mentioned has improved or solved issues. We recently had a 61 Corvette with slow crank when hot. We moved the ground from the frame to the starter mounting bolt and the issue was solved. Within the starter some issues are worn bushings and thrust washers. Causing the armature to not run true. Also within the starter on fresh rebuilds can be brushes that have the wrong copper to carbon ratio. 12v brushes use more copper then carbon. 6v usually are the other way. And 12v brushes in most cases are similar in size and mount and to save money a rebuilder that does not see many 6v starters will use what they have rather then invest for 1 sale the right part. Brushes that have copper wire leads like Ford and Autolite used if the lead on the brush is undersized it can cause issues. Ford used the same brush in both 6v and 12v but the ones 6v ones used the larger lead. The ones made today use the smaller gauge size. The last cause I have found is that the regulator has not been properly set and is undercharging the battery. 6v needs to charge at least 7.0v if not slightly higher based on your driving. Meaning slow speed, short trips need higher. Longer trip higher speed lower end.
  20. Yes we have several hundred of each of those brushes. Give me a call during the week. 1-440-439-1100. Jeff
  21. Looking at a wiring diagram the brake light switch sends power to the turn signal switch and then out to the brake lights. Almost all manufacturers do it this way. It keeps the front turn lights separate so they don't turn one when the brakes are applied. I would say turn signal switch.
  22. Delco-Remy part numbers. Solenoid #'s 1118187 or 1119965. Plunger with linkage #1912055. I can dig thru my stuff if you cant find them elsewhere. You can PM me.
  23. certjeff1

    Battery polarity

    6 volt positive ground
  24. Ok so the part that melts is the plastic insulator for the movable contact. Since the car has been converted to 12v I would leave the original solenoid alone. Get a solenoid for a 1953-1956 Buick along with the plunger and linkage. This will be a 12v setup and they are more readily available then the solenoid you are currently using. Once you get that then you can run tests to see what is causing the problem.
  25. Matt is absolutely right you have to go looking for the cause. Most 6v cars get converted do to complaints of poor or slow cranking speeds. Not all of these problems are the starters fault nor are they the fault of 6v electrical systems. A great many are do to other issues in the system, like cables as an example. The slow cranking speed gets fixed while the cause gets masked by the 12v conversion. It isn't until months or even years or ownership change that the real cause gets fixed. Whatever you decide to do with the starter is up to you. But you need to figure out what is causing your problem.