demon452

You are correct with that assumping. The radiator mounting bracket is different from an a.c. to none A.c. car. . the tabs are for the lower mount that the shroud goes into. Going to need rubber bushings for them. You are going to have to buy an a.c. radiator top mount or possibly modify your existing 1 to work. Also they repop the shrouds I believe they are made from fiberglass. No clue on the quality of the fit. Here is a link for 1 on ebay. https://www.ebay.com/itm/1963-1964-1965-Buick-Riviera-Radiator-Bracket-Top-Upper-Mount-for-AC-Fan-Shroud/232484286245?fits=Year%3A1964|Model%3ARiviera|Make%3ABuick&hash=item362124af25:g:5LAAAOSwfVpYpV8G

I 2nd the bilsteins. Worth the extra cost IMO.

Here is the link to the Dallas riviera. What's with seat covers? https://dallas.craigslist.org/ndf/cto/d/blue-ridge-1964-buick-riviera/6806524675.html

64 riviera on BAT, not mine. Pretty low optioned car. https://bringatrailer.com/listing/1964-buick-riviera-10/

Much appreciated. Thanks, Steve

Does anyone have a wix dual quad air filter part number?Went to orileys and they only one they showed was for the single 4bbl air cleaner.

Well I found the center piece. Was laying on my floor somehow. Anyhow another question. Does anyone reproduce the dash cluster U style seal that goes between the cluster and steering column? If not what have you guys used (meaning size of u seal). Thanks again

Looking for the plastic piece for the turn signal indicator. When i started to reassemble everything I noticed the center is missing. Is that center piece a separate unit or is it 1 piece of plastic (center/indicators)? Thanks

Thanks for helping me find the "Loch Ness Monster" Gene. Received them yesterday. Look good.

Thanks, I actually did plan on putting some ribbon sealer I had left over from the windshield install.

Looks to be a little chilly where she is.

Perfect. I had my doubts about factory. Although it seems to be on the trim that holds the door seal in as well. Thanks, Steve

Anyone? Just added another pic. 2nd pic is the trim I am talking about. Thanks

Could be a possiably. Have to pull the inlet from the tank to fuel pump.See if you feel any suction from the fuel pump. If not there's your problem. If you do may have to trace your rubber lines see if any are broke even on top of the tank connecting to your fuel line. Could be sucking air. Steve

I understand they were a dealer installed option. I just have never seen 1 in that location. I have seen them vary slightly just not that far back. Yes I understand if mounted the same location as the drivers its kinda pointless. But then again I don't have the specs as to where the dealer was supposed to locate them. Unless it was just up to the individual dealer. Also this car does NOT have ac . So the better route would be vintage air. Or cheaper/less headache in the long run.

I go with the tire manufacturer psi (on side of the tire) Not what's in the manual. I highly doubt you are running the factory tires that came on the car when new. As far as misfire kinda tough without driving it. Possiably a low float level or weak fuel pump. Points, ignition etc.. Could be multi things.

Car looks clean from the 1 pic. The passenger side mirror is not factory. Also the location is to far back compared to where the drivers side is. What options does the car have. The 425 was considered a standard engine in 64.

So while installing my dash I noticed the windshield was a little loose. Anyhow I pulled it out to reseal. Now my question is the trim that goes on the A pillar has some sealant? (See pic grey stuff) Is this from the factory or some half ass attempt to repair a window leak? Also if not from the factory was this piece clean or was there some ribbon sealer (black in pic)or something on it to seal? Thanks

Sale pending. Thanks

What is pictured is all I have. Thanks, Steve

I decided I am never going to use these. So up for sale. Now buick seat belts.Never installed some light scratches from handling. $115 shipped. These are just the buckle side. I will accept paypal but have to pay family/friends.

Picked up this banner a mth or so back. Framed it in plexiglass.

Picked up this 64 buick banner a mth or so back. Framed it in plexiglass.

I am actually pretty Suprised you removed all the glue/adhesive with acetone. I tried acetone, mek etc.. The only way I could get it all completely removed was aircraft stripper and a razor blade. Anyhow I used 3M Super 77 . 3m makes multiple adhesives some are better than others. I spray both pieces until tacky then set the vieneer on. I used welding clamps and wood to get equal pressure everywhere. Method is on you, just make sure it is held in place somehow until dried.

How about Howard's lifters? https://www.howardscams.com/hydraulic-roller-retro-fit-street-lifters-buick-400-425-455-howards-cams-91460-2