john hess
-
Posts
498 -
Joined
-
Last visited
Content Type
Forums
Gallery
Events
Posts posted by john hess
-
-
car is sold.... someone got a nice project to finish.... beat me to it.!!!.... good luck on your project... keep us posted... John
-
2
-
1
-
-
car is sold. someone got a good deal on a nice project...
-
the truck.... women cost waaaaay more..... still have my first truck... 🤫
-
2
-
-
if I make the trip... most certainly... this car needs to be finished....
-
2
-
-
I agree.... seems priced right for progress/condition if as described... yes, need to see doors fenders trunk... bumpers ?.... nice project for someone..... had I not just completed my 53 4 door, I would be driving to have a look-see....
-
1
-
-
do you have a bore scope to look inside the tube when installed in the block ? maybe see what's going on at the rear...... just thinkin...
-
actually used a piece of rope, piece of vacuum line, wire ties and the tape...... yea, red/green would be proud.!!
-
1
-
-
couldn't post video.. too big.... but it worked......
-
1
-
-
yea...... well it got me off the road and to autozone!!!!!!... single use only.......
-
1
-
2
-
-
thanks 55er.. they were in the barn.... very nice shape... very minor crease in each one.... should be an easy fix..... close to Hershey if anyone is interested... can deliver to hershey.
-
fender skirts for sale but don't know what they fit... 8.5 inches x 29.5 inches
-
should be here by Thursday....
-
1
-
-
yes,..... had I gone the 'make your own' route, I also would have gone a few thousand undersize also...
-
1
-
-
I now have 3 transmissions.... 1 original.. needs disassembled and cleaned... tailcone bushing disintegrated..... 1 complete and in carcurrently... and 1 almost complete spare for future rebuild.... so I'm sure the tool I 1334 will be put to good use..... thanks guys
-
1
-
-
hi bloo, just found and ordered it... probably just as well.... machining 1 from my guy would take longer.... thinking I would like to have this completed for ETC September meet.
-
1
-
-
revisited tool guy site and resubmitted on ebay listing..... showed available,... so... it's on its way..... thanks again...... John
-
1
-
-
yes, thank you..... buick series 40 is the same, as buick supplied all syncromesh for pontiac.... I will try to contact them..... John
-
thanks nailheadbob.... but I just missed it...... says sold..... guess I'll keep looking.......
-
no serial #....... may be HOT......🤭🤫
-
1
-
-
unknown year......
-
"mine.. not for sale".... my first car... not running, needs tires, good interior, no radio.......engine inoperable......
-
1
-
-
not quite sure on your automatic bellhousing, but my standard, the downpipe bracket bolts to 3rd hole, not 2nd where I'm holding it....
-
not the best , but shows bracket bolted to oil pan, and clamp on draft tube.....
-
1
-
-
downpipe bracket for automatic transmission.... like yours...
draft tube bracket .... this goes under one bolt on oil pan, tab pointing up..... locates draft tube at proper angle..... gets clamped to lower part of the tube....
-
1
-
Timing advance
in Pontiac Flathead Owners
Posted
mark. . looks like your wires are off one position.... pull your #4 wire out of the distributor..... leave disconnected..... pull #1 wire and install.... next, #6, put in #1 hole... move each wire one hole... #4 will be your last wire.... reset distributor to correct position with a timing light.... should correct your misalignment..