GasWorksGarage
Members-
Posts
177 -
Joined
-
Last visited
Content Type
Forums
Gallery
Events
Everything posted by GasWorksGarage
-
57 Chrysler Imperial brake light issue
GasWorksGarage replied to GasWorksGarage's topic in Technical
bulbs are fine -
57 Chrysler Imperial brake light issue
GasWorksGarage replied to GasWorksGarage's topic in Technical
Here is what I have thus far, When I turn on the right signal it stays on as normal until the steering wheel is moved then it cancels. When I rock the switch for the left signal it will not stay on I have to hold the switch in the left position. So I believe that the switch under the steering wheel is bad at least. I have to find the relay and test it. I want to thank all for your input. and thanks to m-mman for the diagram. Keep the info flowing..... -
57 Chrysler Imperial brake light issue
GasWorksGarage replied to GasWorksGarage's topic in Technical
-
57 Chrysler Imperial brake light issue
GasWorksGarage replied to GasWorksGarage's topic in Technical
well I took the turn signal switch out. Its a rocker switch that only has 2 wires on it. -
57 Chrysler Imperial brake light issue
GasWorksGarage replied to GasWorksGarage's topic in Technical
thanks all -
57 Chrysler Imperial brake light issue
GasWorksGarage replied to GasWorksGarage's topic in Technical
Bob, how does the turn signal switch effect the brake lights? Thanks. -
we have a 57 Imperial with no brake lights. running light and turn signals work although the right signal flashes faster than the left but all the bulbs work. there is power into the brake light switch and when you hit the peddle there is power coming out. Any suggestions? Thanks in advance.
-
needing info on Kelly Springfield truck
GasWorksGarage replied to GasWorksGarage's topic in General Discussion
-
Hello, we are trying to determine the year of the truck. we have a truck number of 76086. Can anyone ID this? Thanks
-
orde new filter and gasket from Macs. Thanks all!
-
thanks all. I appreciate the in put. I will be changing the filter as the o ring gasket is leaking.
-
hello, we have a 56 Meter Victoria 292 v8. Can some ID this and tell me where I might find some seals as its leaking. Thanks in advance
-
right at the junction in the disturber
-
Thanks all, I didn't do the conversion and the original parts are not here it is a Pentronics. I found a broken wire it was very hard to see. Runs fine.
-
Hello, we got a 52 Chevrolet in and it has the electronic conversation points kit. We are not getting any spark. Ran fine when we got it, I am hoping someone on here has experience with it, anyway how do I go about testing this unit? Thanks
-
its the small 3 speed
-
Hello, my question is, can the seal around the shaft that goes into the side of the transmission be changed without tearing the transmission apart? Thanks in advance
-
perfect! Thanks
-
Hello, I am in need of the firing order of the 287, actually what I need to know is which terminal on the distributor is #1. Its location to the hold down clip? Thanks
-
1920 Packard Truck
GasWorksGarage replied to Dan Petricca's topic in Automobiles and Parts - Buy/Sell
I have spoke to Dave a few times. He was able to send me some literature but no parts and doesn't know anyone. -
1920 Packard Truck
GasWorksGarage replied to Dan Petricca's topic in Automobiles and Parts - Buy/Sell
I have the engine back together, but I am in need of a starter. Any leads? -
does anyone know where I can find he vin #?
-
Well we were told when we got it that it was a 16. as stated on the title. But Thanks to this forum, we might have been had. Here is a picture of the engine plate.
-
Jon, I got it off. The following numbers are on the side U5 22363 The U5 appear to be cast into the body and the rest stamped.
-
hello, we have a Kelly truck with a 4 cylinder Continental engine in it. The engine has a zenith carb with a governor on it. Does anyone have any information on this engine truck or setup? I need to rebuild the carb. (see photos ) Thanks in advance.