Jump to content

AB-Buff

Members
  • Posts

    191
  • Joined

  • Last visited

Everything posted by AB-Buff

  1. Excellent, great idea. You’re right a pump is a pump. Let us know what you find out!
  2. I'm pretty sure that's not "K" Lincoln... Zephyr v12 different animal
  3. While you have that apart take a picture of the impeller of the one you’re dissecting and the one that you in yours. I’d like to see if there’s any difference in the two. I think Ray mentioned there were three or four different types of impellers (L & K) I’m wondering if they look similar and are not interchangeable?
  4. Matt, thinking out loud I’m wondering if when you get your water pump back if you could put it in a 5 gallon bucket (or bigger) an put the drive end of the pump up and somehow drive that with a drill press motor or even half-inch drive drill just to see if it will pump water. It should circulate some water even at a low shaft speed… I’d love to know what the person thought was possibly wrong with your pump when they’re finished with it. Don’t give up on it, you are almost there. I think it’s going to be a good running car.
  5. Just a couple of photos of the little car show Pacific Grove 2021
  6. Well last month I drove the Lincoln from Tracy to Soquel California and back about a 300 mile round-trip ran great. Then the following Monday I ended up going on a Good Guys run to Sacramento to see a couple of car collections and a tour of Sherm’s customs chrome. Very interesting, the car collections were great. Here is a link to the Kettle Ranch LOC picnic. https://www.americanbantam.com/Lincoln-/2021-LOC-Kuettel-Ranch-Soquel/n-Q8VbHC
  7. I think what you see is when the engine gets so hot the water boils and is forced into the radiator it cools and starts to thermosiphon. There are a few cars do not use water pumps at all and they’re based on a hot water rises cold water doesn’t so it circulates. And this thing is generating a lot of heat so it’s a rather violent event. After a long trip in mine sometimes I’ll pull into the driveway put a fan in front of the radiator in a short time it will cool down because it thermosiphon‘s until the shutters close. Then I don’t have to put a hot car in the shop. Backflushing it wouldn’t hurt but I don’t think there’s anything in it. Matt’s cleaned that puppy pretty good. That engine is going to run fantastic when he’s finished. It’s kind of like Murphy’s Law anything that can happen well and he is just going through a learning experience. But he’s going to know it inside and out.
  8. Matt Talk to Lee at the Brassworks in Paso Robles CA. It's not as expensive as you would think, very reasonable. Heck maybe he can do one for me at the same time and get a bulk discount 🙂 If yo decide to send it there, let me know I may take mine also, be happy to help if I can! Lynn PS he has done them for Lincoln before. Also they are about 3 hors away from me so I can go there if need be
  9. Matt I should mention your oil pressure with than new pump is fantastic. I would like to see if it stays the same in the car. Mine with a fresh oil change (5-40) is 30 psi cold, hot running down the hwy is around 28 psi. After 300 miles it's around 26 psi at hwy speed. 10 psi idling at 450 -500 rpm. All this measured with the gauge that came in the car so I have no idea how close it is, sometime I'll slip a gauge in somewhere to check it.
  10. Hi sorry I have been sidetracked doing other things and haven’t been on the site as much as I probably should have been. But the answer is yes I can start mine up and run it and it doesn’t overheat. However my radiator has been modified and that I have to use a 4 pound pressure cap. If I don’t it will start puking water out like Matt’s and eventually when it gets to a gallon and a half to 2 gallons down it’ll start warming up. I may have discussed this earlier but when my radiator is full and you start it up it needs an air space so it will expel enough water to get that air space. The trouble is after it has that air space and warms up again it will expel more water because of where the overflow tube is located. It’s on the filler neck and water is rushing by it all the time, originally it was at the top of the tank. So if Matt’s radiator has been modified like mine he’ll have to run a 4 pound cap. My plan is, this fall to take it out and take it to the Brassworks in California and have them build me one that will either run with an air space and no pressure or a good 4 pound Radiator that I don’t have to worry about. That’s to be determined. So Matt if your radiator filler cap has the vent right underneath it, put a 4 pound cap on it. Because you will never ever keep water in that radiator without it. The original radiator had a copper tube that came up through the bottom of the top tank and stopped at the very peak of the top inside. It didn’t see any water there at all so it could let air out and in without taking water with it. Hope that makes sense Also there is a lug that was used to fasten a chain to the To keep you from losing the cap inside the filler neck I fill my water level up a quarter inch below that lug and it seems to be good. I might add I drove this to the Lincoln picnic at the Ketel ranch that was about a 300 mile round-trip. It did great. Also last Monday I ended up taking it to a tour of a few car collections in Sacramento, drove it up interstate 5 at 70 miles an hour and back and didn’t have any issues. Yes it has a high speed rear end in it so it was only around 2100 to 2200 RPMs
  11. Matt i’m just remembering you had Lock and Stitch work on that block. You obviously sent the whole engine to them. Did you have the water elbows off at all? Could they have possibly stuffed a rag in it to keep water from leaking on their bench or in their area? Did you check any of that? Also I’m still thinking that you were just not priming the pump I think at this point I would surgically drill a hole for an 8 inch pipe tap, make a nice plug that just fits the ID of that centrifugal pump and not sticking up too far so it looks nice and slowly fill that radiator with that plug out, when water comes out of the top of that pump put that plug in and fill it up. But first check to see if they happen to stick anything in that engine. It’s possible some worker bee stuffed a rag in it to keep water from leaking out of it I don’t know. Just a thought. Easy to do without tearing anything down. if you look at the sketch of that water pump there’s literally 8 inches of air space above the inlet and the outlet. I’ve got a swimming pool and I can let water into my centrifugal pump and it takes it quite a while before it picks up water and flushes the air out , takes a lot longer than you think. L
  12. I keep going over this in my mind and I am inclined to think you are just not getting water flow. All those things you mentioned above in your last post might cause concern. I don’t think you can put the water pump impeller on backwards in that you would not be able to install it into the housing I think it would hit. When you had your water pump off, the elbows on each side of your engine that the water flows through to feed the cylinder blocks, did you happen to look through or push anything through that tube that crosses through your crankcase that water pass from one side to the other? Maybe there is a blockage there? Also on the driver side, that elbow has a fitting on it, somebody added that I’m not sure what that fitting does may be water heater? But I would make sure there’s no blockage there. Also I still think your water pump it is not priming correctly. Like I told you before mine was a booger and for some reason when I filled it through the radiator in allowing the water to flow through radiator first direction that it managed to flush out that bubble quickly. When you do that you cannot have the water lines pinched off anywhere, The engine needs to vent through the upper hoses. I don’t think one tooth on your cam either direction would cause it to heat that fast, if you were running down the road pulling a long grade or something like that I could see it happening. But not in the timeframe that you’re overheating. I believe it’s a flow issue. Somewhere you have a blockage or that pump is just not priming. Also Ed and one of his posts mentioned that at one time his water pump sucked the oil out of the grease cup and it sucked air into his water system. You have a grease cup on your water pump it’s not supposed to. it’s supposed to have a grease zert with a cap to keep it from siphoning. In the meantime take it off and put a plug in it just to see.
  13. Matt just when you think you’ve got everything perfect and ready to go some thing else pops its head up and you have to deal with it. Happens all the time. Right now the hood grill and Radiator are out of the Lincoln. It developed a leak on the passenger side, a previous mechanic decided to put a bolt that holds the hood hole down clamp to the radiator side on with a bolt that’s a half inch too long and it went into the radiator. Hopefully my guy can fix it reasonably fast and reasonably inexpensive. But crap happens. More than you want. Lynn I thought this was a pretty cool picture so I thought I’d post it.
  14. Pretty sure the park lights don't stay on while the headlights are on. I didn't see any thing in your diagram that lead me to think they would. Cole Hersee used to sell an push pull 4 position switch that would work good We use them in the Bantams. Off. park. low and high L
  15. Matt The headlight switch is a little hard to find as is all the piece parts to work it. My 34 was missing all of it also and it took a couple of years to locate all the pieces. Like you said, run it like you have it and just keep an eye out for the parts. You may never change it out but the next guy might. I tried to find a sketch of all the parts on the PC and could not, I will look far a hard copy and scan it for you. Model A switch is a different configuration inside. L 1934-35 headlight switch, maybe through 39?
  16. Hi Alan. It’s a fun one. But just like Matt hardwoods. Lots of years of neglect in semi Standard maintenance. At least in the last few years. But we’re sorting it all out and having fun with it. How is your project coming? Lynn
  17. I had just talked with one of the VPs of the LOC. He said the club is planning on next year. I’m guessing it’s going to be in conjunction with Ford, probably a big event. They are planning a very nice event this year but I don’t think it’s the 100. I’ve been planning on going next year. When Matt wrote it was this year I panicked. I need to find a trailer to use to get my Lincoln there and back. I don’t have an extra $27,000 in the bank to buy a new one, wish I did. Anyway this year‘s festivities look great, But I think the official 100th is next year.
  18. Matt I have been hearing conflicting stories on when the LOC will celebrate the hundredth anniversary. Everybody I talk to now says it is in 2022. 100 years from when Ford bought it from Leland. Anyway maybe there is another hundredth celebration somewhere you’re talking about? Lynn
  19. I’ve got a friend restoring a 33K a Roadster right now. I’ll check with him to see if he’s aware of the shop manual, he’s pretty up on that type of stuff. I’ll get back with you. Still want to see a photo of that car! L I just checked with him. He knows of nothing. Would love to know if there is one.
  20. I posted this once in under trucks. I thought I’d try here. Back in the 70s I owned this truck partially restored and sold it. Looking for the owner of it now, if anybody knows the whereabouts please let me know. I have historical information about it. Lynn
  21. Hi Berry. The book of instructions (owners manual) is a little difficult to find I would recommend searching eBay, may take months to find. But David Clement in the Lincoln Owners Club has them. They are a little pricey. But it’s a very good book to have. Also through the Lincoln Owners Club there is a set of service manuals that covers from 1931 through 39K and some Zephyr. They are also worth getting. I can’t remember what the price was or who to get them from but that information I believe was in every fork and blade issue. Post some pictures of your Lincoln. We’d love to see it. Lynn
  22. No, I use the material I had laying around here. I’m almost embarrassed to tell you what it is but it works fantastic. I cut a piece of it up threw it in some gasoline for a couple of weeks to see if it would dissolved and it didn’t. It’s actually a roofing material called tiger paw. It’s advertised to last 20 years in the sun by itself. It worked fantastic for the diaphragm. If you want a piece I can send you some. It’s not rocket science it’s just a diaphragm and as long as the gasoline won’t eat it up and it doesn’t leak vacuum and it functions properly. It’ll work. L took me a while to grind a photo of the diaphragm
  23. Matt after you get this engine running (hopefully soon) put a vacuum gauge on the port just below the carburetor On the manifold and see what it is. Then when you install it in the car check it again. You may end up having to go through your brake system. There’s a couple of vacuum diaphragms that can go away in time. One is the adjustment that you have on your steering column there’s a diaphragm in there that can develop a leak and then there is what I call an actuator switch controlled by the brake pedal. When you press the brake on it pulls a rod which allows vacuum to go through your selector switch on the steering column to the brake booster underneath the car. When I got mine somebody had rebuilt the booster but they did not mess with the selector switch on the steering column or the actuator switch off of the brake pedal. Both diaphragms had holes in them. The car still ran well but I was losing vacuum. selector, mounts to steering column bad diaphragm actuator mounts to break linkage
×
×
  • Create New...