Jump to content


  • Content Count

  • Joined

  • Last visited

Community Reputation

44 Excellent

About 64Rivvy

  • Rank
    100+ Posts

Recent Profile Visitors

675 profile views
  1. Thanks Pat. Will check that out. That huge gap where it's sagging is def bothering me but Ive wasted enough time on this and had to move forward. Any ideas on where I could find one of those?
  2. I finally got some time to get this done. It took a while longer bc i decided to tape and respray the black trim and ball vent black paint. I also resprayed the silver on the actual plastic plastic bc i must have scratched it up again. A few pointers for anyone doing this and installing a replacement glove door or reinstalling you old door. 1. Cover the entire front of the glove box door with blue or green painters tape when reinstalling. You can only get the dash door in by sliding in from the back and there is no way not to scratch it. Luckily I was paying attention
  3. I can't tells where the actual glove box (black felt box) and the glove box door might overlap and if I assemble the glove box and door outside of the car or i have to screw it you mounts on the dash support inside the car all at once. The screws originally in there were a mishmash with some missing so that's not helping either. There is also an extra oval metal support and I can't remember if there are just one or two of those. The finned aluminum is so delicate and the plastic is brittle so I only want to do it once before stuff starts cracking. I will figure out if theres no re
  4. Bump on this. Hoping to do this later today or tomorrow so hoping I get lucky, otherwise will hack it together.
  5. Makes sense. Thanks for confirming. Will do that before I put the dash back in. Now if I can just figure out the right way to get the glove box and and glovebox door back on.
  6. Do you have the shop manuals? They will help a lot but you might still have questions and people here can help. Are you looking for someone to reassemble it for you nearby, or for help on how to do it yourself? A little unclear in your ask.
  7. I'm trying to put my pass dash panel glovebox and glovebox door back together. I bought it would be straightforward and never took any pics originally when i disassembled it a few years ago. Does anyone have an assembly diagram for this? I went through each of my shop manuals but couldn't find anything on it.
  8. I was going through my 64 Riviera shop manual looking for glove box assembly instructions today and came across this below. Does anyone know of these special magical washers of which the manual speaks?
  9. Rockinrividad, Is this showing that you put felt on both the front edge of the vent housing like my pic number 1 above, and then also on the inner lip of the air vent? I tried the felt on just the air vent inner lip initially and it made no difference, but I didn't think that maybe the felt would go in both places. If that's the correct way I can take it apart and add it to the lip on the air vent tube bc i haven't reinstalled the dash panel yet.
  10. To actually remove the ball vents you need to remove the dash panels and there are bolts and screws that hold the assembly in place. The felt strips i got i think we're for a chevelle and i got them from someplace like inline tube or classic industries. I had passenger side dash panel off bc i replaced the evaporator. I plan to replace the driver's side without removing the panel.
  11. Thanks guys. I did this last night using the felt location in my first pic. I ended up using rubber cement instead of contact cement to give me more time to position it. Took a little longer but came out well. I reassembled it and will post a finished pic later today when i get a few min.
  12. I'm going to roll the dice and go with the option the first pic if no one confirms. Trying to get it all back together.
  13. My ball vents had no original felt left so not sure how they go. Which of the locations below is correct. Does the felt go all the way up to the edge, or further back like the second pic. I am planning to just adhere it with contact cement.
  14. I got mine from opgi. I would check with clarks to see if they still sell it as they may have a better source or better quality foam. Opgi foam was pretty good, just would recommend your upholsterer bolster the sides and edges for a more oem rounded puffy look if you like that look.
  • Create New...