Rufcar

Have any dates been set for 2022 yet? Especially Nationals or Grand Nationals. Tkx Jim F

There are 2 pair used, 1 pair on each side of the hinge. 4 total pieces.

will this work?

When I did my 65 this yr I took an older piece of hose to my federated auto supply and bought about 25ft. I ran it through the car and it worked perfect.

Ed that was installed on my 65 gs when I got it but it didn't work. I found for me the only way was to turn the key to on do 5 light pumps and the car started right up.any other way took 10 15 cranks while pumping all the time. I removed the elect pump system. But I see it works fine for you.

2 manyhobbies, great job on that piece. I needed the rear deck body supports which are behind the rear bumper but I chose to old pieces I bought from Rivi central in calif once I blasted off the light surface rust they were like new. I cut and fit the pieces as needed. They appeared similar to what you just made too.again nice job.

It's white metal so pre fit it after prep of hood and of the trim as you may need to adjust before you final paint. Don't ask how I know. Jim

This is mirror only I never had an additional base as I chromed mine. The mirror is good and no bubbles in chrome. 70 plus shipping

pics of BUICK shroud and non a/c jamb fillers w/o rubbers.

parts request pics and info In the arm rest pic the lower is the good solid black the upper is the saddle w/vinyl removed for pattern. I purchased a pair from a fellow ROA for 50 each and used the best original in my 65. .

ill get the pics of arm rest to you tomorrow Tom. 2 pics of seats before I replaced them. I carefully pulled off the hog rings and roller up seat covers in the box they new ones came in. Just offer what you think they are worth and once you give me your zip I can check on shipping on Monday if your have interest. Tkx Jim

Here is list of items left some new mostly used as I bought a lot of parts and some in bulk. If you have interest I will send you a pic of that item and make an offer plus shipping. 1965 Buick Riviera GS spare parts 1 pr door jamb fillers for a non A/C car no rubber stops Used saddle front seats delux interior. Drivers side torn pass side good. 1 pr arm rests. 1 black perfect 1 saddle needs vinyl Rear frame to chassis rubbers and spacers and bolts 1 pr each 2 a/c heater dash units 2 sets of heater cables 1 new trunk gasket rubber 1 used a/c compressor 2 rear bumper chrome bezels can be re-plated 1 radio filler/control back plate 1 used gas pedal 15 wide flange factory door panel screws 1 headlight bell crack and joint parts. 1 set new power steering hoses 1 nice original complete headlight harness 2 cowl vent screens factory 1 nice original outside mirror and interior trim and clip 1 18” x 24” laminated wiring diagrams new 1 original right side upper trunk cardboard trims (1 clip) 1 lower front bumper core 1 pair rear exterior cast chrome trims on rear roof pillars. Good cores some bubbles 1 nice original hood spear, 2 lower stainless trims 1-14” 1-27” 1 pr of original door sills 1 chrome raised letters “Buick” fan shroud 1 66 fluted wheel cap with wick cat center, the center not good and 1 65 center nice but apart.

Rivdog. I found that once you have access you can use a Flux brush and and some lithium grease you can reach and fell your way into all the tracks and then by moving the window up and down you can oil the rollers. With the new grease and oil and moving the window up and down this should greatly improve the operation.

What I did was cut some vinyl in strip approx. 10" wide and spray glued it along the edges and onto the deteriorating hard foam edges. That gave me a sound edge so any metal won't rub through and allowed the original foam to remain. I did add some softer 1" foam to the center area and a 5" block of foam to under the outer edge of the sunken drivers seat, as that spring was broken. The Clarks vinyl is very firm with a super firm material sewn in so be carful. I am happy with my results but it could be too firm for some.

Ed o believe your talking about seat buttons and the poster us talking about seat bottoms.?

Great find great deal. Congrads. You can buy some r12 cans on ebay sometimes without a license. I have several times. You can usually find some with the filler attachments included. This,way you can fill yourself if you want or a ac service center can use your cans. Jim

I also chose to use bolts and washers as it appears the assembly manual shows some type of push pins. I could be wrong but either way I wanted it to be sturdy as the rubber is old.

as usual good eye Ed. The wood almost looks like formica too! That's the same price I got for mine yesterday.

This is supposedly an all original car. Brought 38,500 plus commissions: http://www.auctionsamerica.com/events/feature-lots.cfm?SaleCode=AF15&ID=r0159&Order=price&feature=&collection=&grouping=&category=\ there was also this 63: http://www.auctionsamerica.com/events/feature-lots.cfm?SaleCode=AF15&ID=r0572&Order=price&feature=&collection=&grouping=&category= there were 2 - 64s one did not make reserve at 30 the other at 20.

Its more of a 20+/- page pamphlet from Mr. Mooney to members of the ROA.

FYI, CAR WAS SOLD TODAY FRI OFF EBAY, AT FULL ASKING PRICE! THE NEW OWNER WILL GET ONE GREAT CAR. THANKS TO EVERYONE HERE ALL YEAR WITH ALL MY RESTORATION QUESTIONS. YOU ARE ALL ONE GREAT GROUP! THANKS AGAIN. JIM FACINELLI

If you have the headlight book on 65s available free as a member here it shows every detail about the headlights and every connector.

Had the transmission done. Did the bottom seal twice runs perfect can burn the tires off the line until it shifts to 2nd.

I have way too many cars and have decided to sell my recently completed GS on ebay. http://www.ebay.com/itm/Buick-Riviera-Gran-Sport-/252080916262?forcerrptr=true&hash=item3ab1318726&item=252080916262

Def a 65 front attached to a 64 rear. Or vise versa.