Jump to content

Bill Jewell

Members
  • Posts

    70
  • Joined

  • Last visited

Everything posted by Bill Jewell

  1. Hello, What is involved in installing a rebuilt clutch and throw-out bearing in a 1930 Franklin 145? Thanks! Bill
  2. Can one of you kind folks tell me what the fluid capacity is for a 1930 Franklin Transmission? Also, what is the proper weight that should be used for the transmission fluid? Thanks for the help! Bill
  3. Don, As far as a replacement for your sheared off screw, you can get two replacement screws at Langs Old Car Parts (www.modeltford.com). Their part number is 5023-4-5. I know these are for a Ford Model T, but they are exact replacements and work fine. My 1930 starters (I have two) do not have the two shims that you show in the picture. Regards, Bill Jewell
  4. Mike, What is the condition of your bendix and how much do you want for it? Can you please send a couple of photos? Thanks Bill
  5. I have a back-up starter (Delco Remy 723-C) for my 1930 Franklin that I need to replace the gear on the bendix. Could someone please advise how to go about replacing the gear? Thanks! Bill
  6. Hello, I have a 1930 Franklin that appears to have the starter stuck to the flywheel. I have been running and driving it recently and now the starter appears to be stuck. Any suggestions on getting it loose? thanks! Bill
  7. I need to buy some Intake and Exhaust Manifold Gaskets for my 1930 Franklin. Anyone know of a good source? Thanks! Bill
  8. Gentlemen, I have a spare starter for my 1930 Franklin that I need to repair or replace the entire bendix mechanism on. Would the Model T bendix set work on my Franklin if I installed the larger spring? Would any other modifications be required? Thanks for the help! Bill
  9. Hello, I have a 1930 Franklin that I need to check for leaks in my Intake manifold and Exhaust manifold. Since the engine heats up so quickly, what is the best way to search for leaks on these two manifolds? Thanks for your help! Bill
  10. Hello, I am attempting to adjust the valves on my 1930 Franklin and have run into an issue that I have not seen before. I adusted the valves for cylinders 1, 4, and 2. When I got to cylinder 6 I am finding that i cannot get the gap to open for the exhaust valve. The "rocker arm" / walking beam will not lift off of the top of the valve no matter how much I turn the screw. I hand cranked the engine a few times and I am seeing the exhaust valve open and close. Am I doing something wrong or is there a problem with the valve or walking beam? Thanks for any help or advise! Have a Great Thanksgiving! Bill Jewell Arlington, Texas (cell) 817-739-8565
  11. what is the total length of a brake shoe return spring for a 32 Auburn? Thanks!!
  12. Gordon, I just need a spring with a hook on each end. The round end was some type of modification made many years ago. Thanks Bill Jewell 817-739-8565
  13. Hello, I am in need of a 9 inch long brake shoe return spring. The "spring" part should be around 4 inches long. Please let me know if you have one or know of a possible source. Thanks! Bill email: Oldradios@aol.com
  14. Sorry, Meant to say... Let me know if you have one or know of a source. Thanks! Bill Jewell
  15. Hello, I am in need of a Brake Shoe Return Spring for a 1930 Franklin. Please let me have one or know of a possible source. A reproduction is fine. Thanks! Bill Jewell email: Oldradios@aol.com
  16. Hello, I have a 1930 Franklin that I just discovered has a broken Brake Drum Spring (the spring that pulls the brake shoes inward, away from the drum). The spring is fairly heavy and is approximately 9 1/8 inch long. I need one fairly quickly and would appreciate any help that you could provide locating one. I have attached a photo of my broken spring. Thanks! Bill Jewell Arlington, Texas email: Oldradios@aol.com
  17. Hello, I just had my Stromberg U-3 carb rebuilt for my 1930 Franklin and need to know what the float setting should be. I measured the fuel pressure and it is 6 PSI when the engine is running. Thanks for the help! Bill
  18. Hello, I have a Franklin rear axle gear with the number 125275 stamped into it. What year Franklin would this be off of? Thanks for the help! Bill
  19. Hello, I am looking for a 1930's Fog Light Switch. Looking for the "push - pull" type and want one that says Fog or Fog Light on the front of knob. I want the type that mounts through a hole in the dash, not the under dash mounting. Thanks for the help! Bill
  20. Hi Lisa, Have you heard from Paul Fitzpatrick recently? He is rebuilding a Stromberg U-3 carburetor for me and I have not heard from him for over 2 months. I have tried to email him and call him and get no response. Thanks! Bill Jewell 817-739-8565
  21. Hello, Has anyone heard from Paul Fitzpatrick recently? He is rebuilding a Stromberg U-3 carburetor for me and I have not heard from him for quite some time. Thanks! Bill Jewell 817-739-8565
  22. I am looking for a replacement door latch spring for my 1930 Franklin Club Sedan. I went to close the door on it a couple of days ago and realized the door latch was not working properly. I removed the latch mechanism from the door and realized the large spring is broken. Any thoughts on where I might locate a replacement? Thanks! Bill Jewell Arlington, Texas
  23. Hello, I need to make a Fuemer cover plate for a missing fuemer on my Stromberg U-3 carburetor. I just wanted to see if someone could offer suggestions. Thank you for any help you can provide! Regards, Bill
  24. Hello, I am looking for a Delco Remy 723-C Starter. Please drop me an email if you have one or know of a lead on one. Email: Oldradios@aol.com Thanks! Bill
×
×
  • Create New...